2
0
mirror of https://github.com/edk2-porting/linux-next.git synced 2024-12-23 12:43:55 +08:00
linux-next/drivers/spi/spi_fsl_spi.c

1193 lines
28 KiB
C
Raw Normal View History

/*
* Freescale SPI controller driver.
*
* Maintainer: Kumar Gala
*
* Copyright (C) 2006 Polycom, Inc.
* Copyright 2010 Freescale Semiconductor, Inc.
*
* CPM SPI and QE buffer descriptors mode support:
* Copyright (c) 2009 MontaVista Software, Inc.
* Author: Anton Vorontsov <avorontsov@ru.mvista.com>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*/
#include <linux/module.h>
#include <linux/types.h>
#include <linux/kernel.h>
#include <linux/interrupt.h>
#include <linux/delay.h>
#include <linux/irq.h>
#include <linux/spi/spi.h>
#include <linux/spi/spi_bitbang.h>
#include <linux/platform_device.h>
#include <linux/fsl_devices.h>
#include <linux/dma-mapping.h>
#include <linux/mm.h>
#include <linux/mutex.h>
#include <linux/of.h>
#include <linux/of_platform.h>
#include <linux/gpio.h>
#include <linux/of_gpio.h>
#include <sysdev/fsl_soc.h>
#include <asm/cpm.h>
#include <asm/qe.h>
#include "spi_fsl_lib.h"
/* CPM1 and CPM2 are mutually exclusive. */
#ifdef CONFIG_CPM1
#include <asm/cpm1.h>
#define CPM_SPI_CMD mk_cr_cmd(CPM_CR_CH_SPI, 0)
#else
#include <asm/cpm2.h>
#define CPM_SPI_CMD mk_cr_cmd(CPM_CR_SPI_PAGE, CPM_CR_SPI_SBLOCK, 0, 0)
#endif
/* SPI Controller registers */
struct fsl_spi_reg {
u8 res1[0x20];
__be32 mode;
__be32 event;
__be32 mask;
__be32 command;
__be32 transmit;
__be32 receive;
};
/* SPI Controller mode register definitions */
#define SPMODE_LOOP (1 << 30)
#define SPMODE_CI_INACTIVEHIGH (1 << 29)
#define SPMODE_CP_BEGIN_EDGECLK (1 << 28)
#define SPMODE_DIV16 (1 << 27)
#define SPMODE_REV (1 << 26)
#define SPMODE_MS (1 << 25)
#define SPMODE_ENABLE (1 << 24)
#define SPMODE_LEN(x) ((x) << 20)
#define SPMODE_PM(x) ((x) << 16)
#define SPMODE_OP (1 << 14)
#define SPMODE_CG(x) ((x) << 7)
/*
* Default for SPI Mode:
* SPI MODE 0 (inactive low, phase middle, MSB, 8-bit length, slow clk
*/
#define SPMODE_INIT_VAL (SPMODE_CI_INACTIVEHIGH | SPMODE_DIV16 | SPMODE_REV | \
SPMODE_MS | SPMODE_LEN(7) | SPMODE_PM(0xf))
/* SPIE register values */
#define SPIE_NE 0x00000200 /* Not empty */
#define SPIE_NF 0x00000100 /* Not full */
/* SPIM register values */
#define SPIM_NE 0x00000200 /* Not empty */
#define SPIM_NF 0x00000100 /* Not full */
#define SPIE_TXB 0x00000200 /* Last char is written to tx fifo */
#define SPIE_RXB 0x00000100 /* Last char is written to rx buf */
/* SPCOM register values */
#define SPCOM_STR (1 << 23) /* Start transmit */
#define SPI_PRAM_SIZE 0x100
#define SPI_MRBLR ((unsigned int)PAGE_SIZE)
static void *fsl_dummy_rx;
static DEFINE_MUTEX(fsl_dummy_rx_lock);
static int fsl_dummy_rx_refcnt;
static void fsl_spi_change_mode(struct spi_device *spi)
{
struct mpc8xxx_spi *mspi = spi_master_get_devdata(spi->master);
struct spi_mpc8xxx_cs *cs = spi->controller_state;
struct fsl_spi_reg *reg_base = mspi->reg_base;
__be32 __iomem *mode = &reg_base->mode;
unsigned long flags;
if (cs->hw_mode == mpc8xxx_spi_read_reg(mode))
return;
/* Turn off IRQs locally to minimize time that SPI is disabled. */
local_irq_save(flags);
/* Turn off SPI unit prior changing mode */
mpc8xxx_spi_write_reg(mode, cs->hw_mode & ~SPMODE_ENABLE);
/* When in CPM mode, we need to reinit tx and rx. */
if (mspi->flags & SPI_CPM_MODE) {
if (mspi->flags & SPI_QE) {
qe_issue_cmd(QE_INIT_TX_RX, mspi->subblock,
QE_CR_PROTOCOL_UNSPECIFIED, 0);
} else {
cpm_command(CPM_SPI_CMD, CPM_CR_INIT_TRX);
if (mspi->flags & SPI_CPM1) {
out_be16(&mspi->pram->rbptr,
in_be16(&mspi->pram->rbase));
out_be16(&mspi->pram->tbptr,
in_be16(&mspi->pram->tbase));
}
}
}
mpc8xxx_spi_write_reg(mode, cs->hw_mode);
local_irq_restore(flags);
}
static void fsl_spi_chipselect(struct spi_device *spi, int value)
{
struct mpc8xxx_spi *mpc8xxx_spi = spi_master_get_devdata(spi->master);
struct fsl_spi_platform_data *pdata = spi->dev.parent->platform_data;
bool pol = spi->mode & SPI_CS_HIGH;
struct spi_mpc8xxx_cs *cs = spi->controller_state;
if (value == BITBANG_CS_INACTIVE) {
if (pdata->cs_control)
pdata->cs_control(spi, !pol);
}
if (value == BITBANG_CS_ACTIVE) {
mpc8xxx_spi->rx_shift = cs->rx_shift;
mpc8xxx_spi->tx_shift = cs->tx_shift;
mpc8xxx_spi->get_rx = cs->get_rx;
mpc8xxx_spi->get_tx = cs->get_tx;
fsl_spi_change_mode(spi);
if (pdata->cs_control)
pdata->cs_control(spi, pol);
}
}
static int mspi_apply_cpu_mode_quirks(struct spi_mpc8xxx_cs *cs,
struct spi_device *spi,
struct mpc8xxx_spi *mpc8xxx_spi,
int bits_per_word)
{
cs->rx_shift = 0;
cs->tx_shift = 0;
if (bits_per_word <= 8) {
cs->get_rx = mpc8xxx_spi_rx_buf_u8;
cs->get_tx = mpc8xxx_spi_tx_buf_u8;
if (mpc8xxx_spi->flags & SPI_QE_CPU_MODE) {
cs->rx_shift = 16;
cs->tx_shift = 24;
}
} else if (bits_per_word <= 16) {
cs->get_rx = mpc8xxx_spi_rx_buf_u16;
cs->get_tx = mpc8xxx_spi_tx_buf_u16;
if (mpc8xxx_spi->flags & SPI_QE_CPU_MODE) {
cs->rx_shift = 16;
cs->tx_shift = 16;
}
} else if (bits_per_word <= 32) {
cs->get_rx = mpc8xxx_spi_rx_buf_u32;
cs->get_tx = mpc8xxx_spi_tx_buf_u32;
} else
return -EINVAL;
if (mpc8xxx_spi->flags & SPI_QE_CPU_MODE &&
spi->mode & SPI_LSB_FIRST) {
cs->tx_shift = 0;
if (bits_per_word <= 8)
cs->rx_shift = 8;
else
cs->rx_shift = 0;
}
mpc8xxx_spi->rx_shift = cs->rx_shift;
mpc8xxx_spi->tx_shift = cs->tx_shift;
mpc8xxx_spi->get_rx = cs->get_rx;
mpc8xxx_spi->get_tx = cs->get_tx;
return bits_per_word;
}
static int mspi_apply_qe_mode_quirks(struct spi_mpc8xxx_cs *cs,
struct spi_device *spi,
int bits_per_word)
{
/* QE uses Little Endian for words > 8
* so transform all words > 8 into 8 bits
* Unfortnatly that doesn't work for LSB so
* reject these for now */
/* Note: 32 bits word, LSB works iff
* tfcr/rfcr is set to CPMFCR_GBL */
if (spi->mode & SPI_LSB_FIRST &&
bits_per_word > 8)
return -EINVAL;
if (bits_per_word > 8)
return 8; /* pretend its 8 bits */
return bits_per_word;
}
static int fsl_spi_setup_transfer(struct spi_device *spi,
struct spi_transfer *t)
{
struct mpc8xxx_spi *mpc8xxx_spi;
int bits_per_word = 0;
u8 pm;
u32 hz = 0;
struct spi_mpc8xxx_cs *cs = spi->controller_state;
mpc8xxx_spi = spi_master_get_devdata(spi->master);
if (t) {
bits_per_word = t->bits_per_word;
hz = t->speed_hz;
}
/* spi_transfer level calls that work per-word */
if (!bits_per_word)
bits_per_word = spi->bits_per_word;
/* Make sure its a bit width we support [4..16, 32] */
if ((bits_per_word < 4)
|| ((bits_per_word > 16) && (bits_per_word != 32)))
return -EINVAL;
if (!hz)
hz = spi->max_speed_hz;
if (!(mpc8xxx_spi->flags & SPI_CPM_MODE))
bits_per_word = mspi_apply_cpu_mode_quirks(cs, spi,
mpc8xxx_spi,
bits_per_word);
else if (mpc8xxx_spi->flags & SPI_QE)
bits_per_word = mspi_apply_qe_mode_quirks(cs, spi,
bits_per_word);
if (bits_per_word < 0)
return bits_per_word;
if (bits_per_word == 32)
bits_per_word = 0;
else
bits_per_word = bits_per_word - 1;
/* mask out bits we are going to set */
cs->hw_mode &= ~(SPMODE_LEN(0xF) | SPMODE_DIV16
| SPMODE_PM(0xF));
cs->hw_mode |= SPMODE_LEN(bits_per_word);
if ((mpc8xxx_spi->spibrg / hz) > 64) {
cs->hw_mode |= SPMODE_DIV16;
spi: Correct SPI clock frequency setting in spi_mpc8xxx Correct SPI clock frequency division factor rounding, preventing clock rates higher than the maximum specified clock frequency being used. When specifying spi-max-frequency = <10000000> in the device tree, the resulting frequency was 11.1 MHz, with spibrg being 133333332. According to the freescale data sheet [1], the spi clock rate is spiclk = spibrg / (4 * (pm+1)) The existing code calculated pm = mpc8xxx_spi->spibrg / (hz * 4); pm--; resulting in pm = (int) (3.3333) - 1 = 2, resulting in spiclk = 133333332/(4*(2+1)) = 11111111 With the fix, pm = (mpc8xxx_spi->spibrg - 1) / (hz * 4) + 1; pm--; resulting in pm = (int) (4.3333) - 1 = 3, resulting in spiclk = 133333332/(4*(3+1)) = 8333333 Without the fix, for every desired SPI frequency that is not exactly derivable from spibrg, pm will be too small due to rounding down, resulting in a too high SPI clock, so we need a pm which is one higher. For values that are exactly derivable, spibrg will be dividable by (hz*4) without remainder, and (int) ((spibrg-1)/(hz*4)) will be one lower than (int) (spibrg)/(hz*4), which is compensated by adding 1. For these values, the fixed version calculates the same pm as the unfixed version. For all values that are not exactly derivable, spibrg will be not dividable by (hz*4) without remainder, and (int) ((spibrg-1)/(hz*4)) will be the same as (int) (spibrg)/(hz*4), and the calculated pm will be one higher than calculated by the unfixed version. References: [1] http://www.freescale.com/files/32bit/doc/ref_manual/MPC8315ERM.pdf, page 22-10 -> 1398 Signed-off-by: Ernst Schwab <eschwab@online.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-02-17 12:02:57 +08:00
pm = (mpc8xxx_spi->spibrg - 1) / (hz * 64) + 1;
WARN_ONCE(pm > 16, "%s: Requested speed is too low: %d Hz. "
"Will use %d Hz instead.\n", dev_name(&spi->dev),
hz, mpc8xxx_spi->spibrg / 1024);
if (pm > 16)
pm = 16;
} else {
spi: Correct SPI clock frequency setting in spi_mpc8xxx Correct SPI clock frequency division factor rounding, preventing clock rates higher than the maximum specified clock frequency being used. When specifying spi-max-frequency = <10000000> in the device tree, the resulting frequency was 11.1 MHz, with spibrg being 133333332. According to the freescale data sheet [1], the spi clock rate is spiclk = spibrg / (4 * (pm+1)) The existing code calculated pm = mpc8xxx_spi->spibrg / (hz * 4); pm--; resulting in pm = (int) (3.3333) - 1 = 2, resulting in spiclk = 133333332/(4*(2+1)) = 11111111 With the fix, pm = (mpc8xxx_spi->spibrg - 1) / (hz * 4) + 1; pm--; resulting in pm = (int) (4.3333) - 1 = 3, resulting in spiclk = 133333332/(4*(3+1)) = 8333333 Without the fix, for every desired SPI frequency that is not exactly derivable from spibrg, pm will be too small due to rounding down, resulting in a too high SPI clock, so we need a pm which is one higher. For values that are exactly derivable, spibrg will be dividable by (hz*4) without remainder, and (int) ((spibrg-1)/(hz*4)) will be one lower than (int) (spibrg)/(hz*4), which is compensated by adding 1. For these values, the fixed version calculates the same pm as the unfixed version. For all values that are not exactly derivable, spibrg will be not dividable by (hz*4) without remainder, and (int) ((spibrg-1)/(hz*4)) will be the same as (int) (spibrg)/(hz*4), and the calculated pm will be one higher than calculated by the unfixed version. References: [1] http://www.freescale.com/files/32bit/doc/ref_manual/MPC8315ERM.pdf, page 22-10 -> 1398 Signed-off-by: Ernst Schwab <eschwab@online.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-02-17 12:02:57 +08:00
pm = (mpc8xxx_spi->spibrg - 1) / (hz * 4) + 1;
}
if (pm)
pm--;
cs->hw_mode |= SPMODE_PM(pm);
fsl_spi_change_mode(spi);
return 0;
}
static void fsl_spi_cpm_bufs_start(struct mpc8xxx_spi *mspi)
{
struct cpm_buf_desc __iomem *tx_bd = mspi->tx_bd;
struct cpm_buf_desc __iomem *rx_bd = mspi->rx_bd;
unsigned int xfer_len = min(mspi->count, SPI_MRBLR);
unsigned int xfer_ofs;
struct fsl_spi_reg *reg_base = mspi->reg_base;
xfer_ofs = mspi->xfer_in_progress->len - mspi->count;
if (mspi->rx_dma == mspi->dma_dummy_rx)
out_be32(&rx_bd->cbd_bufaddr, mspi->rx_dma);
else
out_be32(&rx_bd->cbd_bufaddr, mspi->rx_dma + xfer_ofs);
out_be16(&rx_bd->cbd_datlen, 0);
out_be16(&rx_bd->cbd_sc, BD_SC_EMPTY | BD_SC_INTRPT | BD_SC_WRAP);
if (mspi->tx_dma == mspi->dma_dummy_tx)
out_be32(&tx_bd->cbd_bufaddr, mspi->tx_dma);
else
out_be32(&tx_bd->cbd_bufaddr, mspi->tx_dma + xfer_ofs);
out_be16(&tx_bd->cbd_datlen, xfer_len);
out_be16(&tx_bd->cbd_sc, BD_SC_READY | BD_SC_INTRPT | BD_SC_WRAP |
BD_SC_LAST);
/* start transfer */
mpc8xxx_spi_write_reg(&reg_base->command, SPCOM_STR);
}
static int fsl_spi_cpm_bufs(struct mpc8xxx_spi *mspi,
struct spi_transfer *t, bool is_dma_mapped)
{
struct device *dev = mspi->dev;
struct fsl_spi_reg *reg_base = mspi->reg_base;
if (is_dma_mapped) {
mspi->map_tx_dma = 0;
mspi->map_rx_dma = 0;
} else {
mspi->map_tx_dma = 1;
mspi->map_rx_dma = 1;
}
if (!t->tx_buf) {
mspi->tx_dma = mspi->dma_dummy_tx;
mspi->map_tx_dma = 0;
}
if (!t->rx_buf) {
mspi->rx_dma = mspi->dma_dummy_rx;
mspi->map_rx_dma = 0;
}
if (mspi->map_tx_dma) {
void *nonconst_tx = (void *)mspi->tx; /* shut up gcc */
mspi->tx_dma = dma_map_single(dev, nonconst_tx, t->len,
DMA_TO_DEVICE);
if (dma_mapping_error(dev, mspi->tx_dma)) {
dev_err(dev, "unable to map tx dma\n");
return -ENOMEM;
}
} else if (t->tx_buf) {
mspi->tx_dma = t->tx_dma;
}
if (mspi->map_rx_dma) {
mspi->rx_dma = dma_map_single(dev, mspi->rx, t->len,
DMA_FROM_DEVICE);
if (dma_mapping_error(dev, mspi->rx_dma)) {
dev_err(dev, "unable to map rx dma\n");
goto err_rx_dma;
}
} else if (t->rx_buf) {
mspi->rx_dma = t->rx_dma;
}
/* enable rx ints */
mpc8xxx_spi_write_reg(&reg_base->mask, SPIE_RXB);
mspi->xfer_in_progress = t;
mspi->count = t->len;
/* start CPM transfers */
fsl_spi_cpm_bufs_start(mspi);
return 0;
err_rx_dma:
if (mspi->map_tx_dma)
dma_unmap_single(dev, mspi->tx_dma, t->len, DMA_TO_DEVICE);
return -ENOMEM;
}
static void fsl_spi_cpm_bufs_complete(struct mpc8xxx_spi *mspi)
{
struct device *dev = mspi->dev;
struct spi_transfer *t = mspi->xfer_in_progress;
if (mspi->map_tx_dma)
dma_unmap_single(dev, mspi->tx_dma, t->len, DMA_TO_DEVICE);
if (mspi->map_rx_dma)
dma_unmap_single(dev, mspi->rx_dma, t->len, DMA_FROM_DEVICE);
mspi->xfer_in_progress = NULL;
}
static int fsl_spi_cpu_bufs(struct mpc8xxx_spi *mspi,
struct spi_transfer *t, unsigned int len)
{
u32 word;
struct fsl_spi_reg *reg_base = mspi->reg_base;
mspi->count = len;
/* enable rx ints */
mpc8xxx_spi_write_reg(&reg_base->mask, SPIM_NE);
/* transmit word */
word = mspi->get_tx(mspi);
mpc8xxx_spi_write_reg(&reg_base->transmit, word);
return 0;
}
static int fsl_spi_bufs(struct spi_device *spi, struct spi_transfer *t,
bool is_dma_mapped)
{
struct mpc8xxx_spi *mpc8xxx_spi = spi_master_get_devdata(spi->master);
struct fsl_spi_reg *reg_base;
unsigned int len = t->len;
u8 bits_per_word;
int ret;
reg_base = mpc8xxx_spi->reg_base;
bits_per_word = spi->bits_per_word;
if (t->bits_per_word)
bits_per_word = t->bits_per_word;
if (bits_per_word > 8) {
/* invalid length? */
if (len & 1)
return -EINVAL;
len /= 2;
}
if (bits_per_word > 16) {
/* invalid length? */
if (len & 1)
return -EINVAL;
len /= 2;
}
mpc8xxx_spi->tx = t->tx_buf;
mpc8xxx_spi->rx = t->rx_buf;
INIT_COMPLETION(mpc8xxx_spi->done);
if (mpc8xxx_spi->flags & SPI_CPM_MODE)
ret = fsl_spi_cpm_bufs(mpc8xxx_spi, t, is_dma_mapped);
else
ret = fsl_spi_cpu_bufs(mpc8xxx_spi, t, len);
if (ret)
return ret;
wait_for_completion(&mpc8xxx_spi->done);
/* disable rx ints */
mpc8xxx_spi_write_reg(&reg_base->mask, 0);
if (mpc8xxx_spi->flags & SPI_CPM_MODE)
fsl_spi_cpm_bufs_complete(mpc8xxx_spi);
return mpc8xxx_spi->count;
}
static void fsl_spi_do_one_msg(struct spi_message *m)
{
struct spi_device *spi = m->spi;
struct spi_transfer *t;
unsigned int cs_change;
const int nsecs = 50;
int status;
cs_change = 1;
status = 0;
list_for_each_entry(t, &m->transfers, transfer_list) {
if (t->bits_per_word || t->speed_hz) {
/* Don't allow changes if CS is active */
status = -EINVAL;
if (cs_change)
status = fsl_spi_setup_transfer(spi, t);
if (status < 0)
break;
}
if (cs_change) {
fsl_spi_chipselect(spi, BITBANG_CS_ACTIVE);
ndelay(nsecs);
}
cs_change = t->cs_change;
if (t->len)
status = fsl_spi_bufs(spi, t, m->is_dma_mapped);
if (status) {
status = -EMSGSIZE;
break;
}
m->actual_length += t->len;
if (t->delay_usecs)
udelay(t->delay_usecs);
if (cs_change) {
ndelay(nsecs);
fsl_spi_chipselect(spi, BITBANG_CS_INACTIVE);
ndelay(nsecs);
}
}
m->status = status;
m->complete(m->context);
if (status || !cs_change) {
ndelay(nsecs);
fsl_spi_chipselect(spi, BITBANG_CS_INACTIVE);
}
fsl_spi_setup_transfer(spi, NULL);
}
static int fsl_spi_setup(struct spi_device *spi)
{
struct mpc8xxx_spi *mpc8xxx_spi;
struct fsl_spi_reg *reg_base;
int retval;
u32 hw_mode;
struct spi_mpc8xxx_cs *cs = spi->controller_state;
if (!spi->max_speed_hz)
return -EINVAL;
if (!cs) {
cs = kzalloc(sizeof *cs, GFP_KERNEL);
if (!cs)
return -ENOMEM;
spi->controller_state = cs;
}
mpc8xxx_spi = spi_master_get_devdata(spi->master);
reg_base = mpc8xxx_spi->reg_base;
hw_mode = cs->hw_mode; /* Save original settings */
cs->hw_mode = mpc8xxx_spi_read_reg(&reg_base->mode);
/* mask out bits we are going to set */
cs->hw_mode &= ~(SPMODE_CP_BEGIN_EDGECLK | SPMODE_CI_INACTIVEHIGH
| SPMODE_REV | SPMODE_LOOP);
if (spi->mode & SPI_CPHA)
cs->hw_mode |= SPMODE_CP_BEGIN_EDGECLK;
if (spi->mode & SPI_CPOL)
cs->hw_mode |= SPMODE_CI_INACTIVEHIGH;
if (!(spi->mode & SPI_LSB_FIRST))
cs->hw_mode |= SPMODE_REV;
if (spi->mode & SPI_LOOP)
cs->hw_mode |= SPMODE_LOOP;
retval = fsl_spi_setup_transfer(spi, NULL);
if (retval < 0) {
cs->hw_mode = hw_mode; /* Restore settings */
return retval;
}
return 0;
}
static void fsl_spi_cpm_irq(struct mpc8xxx_spi *mspi, u32 events)
{
u16 len;
struct fsl_spi_reg *reg_base = mspi->reg_base;
dev_dbg(mspi->dev, "%s: bd datlen %d, count %d\n", __func__,
in_be16(&mspi->rx_bd->cbd_datlen), mspi->count);
len = in_be16(&mspi->rx_bd->cbd_datlen);
if (len > mspi->count) {
WARN_ON(1);
len = mspi->count;
}
/* Clear the events */
mpc8xxx_spi_write_reg(&reg_base->event, events);
mspi->count -= len;
if (mspi->count)
fsl_spi_cpm_bufs_start(mspi);
else
complete(&mspi->done);
}
static void fsl_spi_cpu_irq(struct mpc8xxx_spi *mspi, u32 events)
{
struct fsl_spi_reg *reg_base = mspi->reg_base;
/* We need handle RX first */
if (events & SPIE_NE) {
u32 rx_data = mpc8xxx_spi_read_reg(&reg_base->receive);
if (mspi->rx)
mspi->get_rx(rx_data, mspi);
}
if ((events & SPIE_NF) == 0)
/* spin until TX is done */
while (((events =
mpc8xxx_spi_read_reg(&reg_base->event)) &
SPIE_NF) == 0)
spi_mpc83xx: fix checkpatch issues Checkpatch is spitting errors when seeing the rename patch, so fix the errors prior to moving. Following errors and warnings were fixed: WARNING: Use #include <linux/io.h> instead of <asm/io.h> #1027: FILE: drivers/spi/spi_mpc8xxx.c:37: +#include <asm/io.h> ERROR: "foo * bar" should be "foo *bar" #1111: FILE: drivers/spi/spi_mpc8xxx.c:121: +static inline void mpc83xx_spi_write_reg(__be32 __iomem * reg, u32 val) ERROR: "foo * bar" should be "foo *bar" #1116: FILE: drivers/spi/spi_mpc8xxx.c:126: +static inline u32 mpc83xx_spi_read_reg(__be32 __iomem * reg) ERROR: "foo * bar" should be "foo *bar" #1125: FILE: drivers/spi/spi_mpc8xxx.c:135: + type * rx = mpc83xx_spi->rx; \ ERROR: "foo * bar" should be "foo *bar" #1135: FILE: drivers/spi/spi_mpc8xxx.c:145: + const type * tx = mpc83xx_spi->tx; \ WARNING: suspect code indent for conditional statements (16, 25) #1504: FILE: drivers/spi/spi_mpc8xxx.c:514: + while (((event = [...] + cpu_relax(); Following warnings were left over, since fixing them will hurt the readability. We'd better fix them by lowering the indentation level by splitting mpc83xx_spi_work function into two parts. WARNING: line over 80 characters #1371: FILE: drivers/spi/spi_mpc8xxx.c:381: + status = mpc83xx_spi_setup_transfer(spi, t); WARNING: line over 80 characters #1392: FILE: drivers/spi/spi_mpc8xxx.c:402: + mpc83xx_spi_chipselect(spi, BITBANG_CS_INACTIVE); Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: Kumar Gala <galak@gate.crashing.org> Cc: David Brownell <david-b@pacbell.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-19 07:49:05 +08:00
cpu_relax();
/* Clear the events */
mpc8xxx_spi_write_reg(&reg_base->event, events);
mspi->count -= 1;
if (mspi->count) {
u32 word = mspi->get_tx(mspi);
mpc8xxx_spi_write_reg(&reg_base->transmit, word);
} else {
complete(&mspi->done);
}
}
static irqreturn_t fsl_spi_irq(s32 irq, void *context_data)
{
struct mpc8xxx_spi *mspi = context_data;
irqreturn_t ret = IRQ_NONE;
u32 events;
struct fsl_spi_reg *reg_base = mspi->reg_base;
/* Get interrupt events(tx/rx) */
events = mpc8xxx_spi_read_reg(&reg_base->event);
if (events)
ret = IRQ_HANDLED;
dev_dbg(mspi->dev, "%s: events %x\n", __func__, events);
if (mspi->flags & SPI_CPM_MODE)
fsl_spi_cpm_irq(mspi, events);
else
fsl_spi_cpu_irq(mspi, events);
return ret;
}
static void *fsl_spi_alloc_dummy_rx(void)
{
mutex_lock(&fsl_dummy_rx_lock);
if (!fsl_dummy_rx)
fsl_dummy_rx = kmalloc(SPI_MRBLR, GFP_KERNEL);
if (fsl_dummy_rx)
fsl_dummy_rx_refcnt++;
mutex_unlock(&fsl_dummy_rx_lock);
return fsl_dummy_rx;
}
static void fsl_spi_free_dummy_rx(void)
{
mutex_lock(&fsl_dummy_rx_lock);
switch (fsl_dummy_rx_refcnt) {
case 0:
WARN_ON(1);
break;
case 1:
kfree(fsl_dummy_rx);
fsl_dummy_rx = NULL;
/* fall through */
default:
fsl_dummy_rx_refcnt--;
break;
}
mutex_unlock(&fsl_dummy_rx_lock);
}
static unsigned long fsl_spi_cpm_get_pram(struct mpc8xxx_spi *mspi)
{
struct device *dev = mspi->dev;
struct device_node *np = dev->of_node;
const u32 *iprop;
int size;
unsigned long spi_base_ofs;
unsigned long pram_ofs = -ENOMEM;
/* Can't use of_address_to_resource(), QE muram isn't at 0. */
iprop = of_get_property(np, "reg", &size);
/* QE with a fixed pram location? */
if (mspi->flags & SPI_QE && iprop && size == sizeof(*iprop) * 4)
return cpm_muram_alloc_fixed(iprop[2], SPI_PRAM_SIZE);
/* QE but with a dynamic pram location? */
if (mspi->flags & SPI_QE) {
pram_ofs = cpm_muram_alloc(SPI_PRAM_SIZE, 64);
qe_issue_cmd(QE_ASSIGN_PAGE_TO_DEVICE, mspi->subblock,
QE_CR_PROTOCOL_UNSPECIFIED, pram_ofs);
return pram_ofs;
}
/* CPM1 and CPM2 pram must be at a fixed addr. */
if (!iprop || size != sizeof(*iprop) * 4)
return -ENOMEM;
spi_base_ofs = cpm_muram_alloc_fixed(iprop[2], 2);
if (IS_ERR_VALUE(spi_base_ofs))
return -ENOMEM;
if (mspi->flags & SPI_CPM2) {
pram_ofs = cpm_muram_alloc(SPI_PRAM_SIZE, 64);
if (!IS_ERR_VALUE(pram_ofs)) {
u16 __iomem *spi_base = cpm_muram_addr(spi_base_ofs);
out_be16(spi_base, pram_ofs);
}
} else {
struct spi_pram __iomem *pram = cpm_muram_addr(spi_base_ofs);
u16 rpbase = in_be16(&pram->rpbase);
/* Microcode relocation patch applied? */
if (rpbase)
pram_ofs = rpbase;
else
return spi_base_ofs;
}
cpm_muram_free(spi_base_ofs);
return pram_ofs;
}
static int fsl_spi_cpm_init(struct mpc8xxx_spi *mspi)
{
struct device *dev = mspi->dev;
struct device_node *np = dev->of_node;
const u32 *iprop;
int size;
unsigned long pram_ofs;
unsigned long bds_ofs;
if (!(mspi->flags & SPI_CPM_MODE))
return 0;
if (!fsl_spi_alloc_dummy_rx())
return -ENOMEM;
if (mspi->flags & SPI_QE) {
iprop = of_get_property(np, "cell-index", &size);
if (iprop && size == sizeof(*iprop))
mspi->subblock = *iprop;
switch (mspi->subblock) {
default:
dev_warn(dev, "cell-index unspecified, assuming SPI1");
/* fall through */
case 0:
mspi->subblock = QE_CR_SUBBLOCK_SPI1;
break;
case 1:
mspi->subblock = QE_CR_SUBBLOCK_SPI2;
break;
}
}
pram_ofs = fsl_spi_cpm_get_pram(mspi);
if (IS_ERR_VALUE(pram_ofs)) {
dev_err(dev, "can't allocate spi parameter ram\n");
goto err_pram;
}
bds_ofs = cpm_muram_alloc(sizeof(*mspi->tx_bd) +
sizeof(*mspi->rx_bd), 8);
if (IS_ERR_VALUE(bds_ofs)) {
dev_err(dev, "can't allocate bds\n");
goto err_bds;
}
mspi->dma_dummy_tx = dma_map_single(dev, empty_zero_page, PAGE_SIZE,
DMA_TO_DEVICE);
if (dma_mapping_error(dev, mspi->dma_dummy_tx)) {
dev_err(dev, "unable to map dummy tx buffer\n");
goto err_dummy_tx;
}
mspi->dma_dummy_rx = dma_map_single(dev, fsl_dummy_rx, SPI_MRBLR,
DMA_FROM_DEVICE);
if (dma_mapping_error(dev, mspi->dma_dummy_rx)) {
dev_err(dev, "unable to map dummy rx buffer\n");
goto err_dummy_rx;
}
mspi->pram = cpm_muram_addr(pram_ofs);
mspi->tx_bd = cpm_muram_addr(bds_ofs);
mspi->rx_bd = cpm_muram_addr(bds_ofs + sizeof(*mspi->tx_bd));
/* Initialize parameter ram. */
out_be16(&mspi->pram->tbase, cpm_muram_offset(mspi->tx_bd));
out_be16(&mspi->pram->rbase, cpm_muram_offset(mspi->rx_bd));
out_8(&mspi->pram->tfcr, CPMFCR_EB | CPMFCR_GBL);
out_8(&mspi->pram->rfcr, CPMFCR_EB | CPMFCR_GBL);
out_be16(&mspi->pram->mrblr, SPI_MRBLR);
out_be32(&mspi->pram->rstate, 0);
out_be32(&mspi->pram->rdp, 0);
out_be16(&mspi->pram->rbptr, 0);
out_be16(&mspi->pram->rbc, 0);
out_be32(&mspi->pram->rxtmp, 0);
out_be32(&mspi->pram->tstate, 0);
out_be32(&mspi->pram->tdp, 0);
out_be16(&mspi->pram->tbptr, 0);
out_be16(&mspi->pram->tbc, 0);
out_be32(&mspi->pram->txtmp, 0);
return 0;
err_dummy_rx:
dma_unmap_single(dev, mspi->dma_dummy_tx, PAGE_SIZE, DMA_TO_DEVICE);
err_dummy_tx:
cpm_muram_free(bds_ofs);
err_bds:
cpm_muram_free(pram_ofs);
err_pram:
fsl_spi_free_dummy_rx();
return -ENOMEM;
}
static void fsl_spi_cpm_free(struct mpc8xxx_spi *mspi)
{
struct device *dev = mspi->dev;
dma_unmap_single(dev, mspi->dma_dummy_rx, SPI_MRBLR, DMA_FROM_DEVICE);
dma_unmap_single(dev, mspi->dma_dummy_tx, PAGE_SIZE, DMA_TO_DEVICE);
cpm_muram_free(cpm_muram_offset(mspi->tx_bd));
cpm_muram_free(cpm_muram_offset(mspi->pram));
fsl_spi_free_dummy_rx();
}
static void fsl_spi_remove(struct mpc8xxx_spi *mspi)
{
iounmap(mspi->reg_base);
fsl_spi_cpm_free(mspi);
}
static struct spi_master * __devinit fsl_spi_probe(struct device *dev,
struct resource *mem, unsigned int irq)
{
struct fsl_spi_platform_data *pdata = dev->platform_data;
struct spi_master *master;
struct mpc8xxx_spi *mpc8xxx_spi;
struct fsl_spi_reg *reg_base;
u32 regval;
int ret = 0;
master = spi_alloc_master(dev, sizeof(struct mpc8xxx_spi));
if (master == NULL) {
ret = -ENOMEM;
goto err;
}
dev_set_drvdata(dev, master);
ret = mpc8xxx_spi_probe(dev, mem, irq);
if (ret)
goto err_probe;
master->setup = fsl_spi_setup;
mpc8xxx_spi = spi_master_get_devdata(master);
mpc8xxx_spi->spi_do_one_msg = fsl_spi_do_one_msg;
mpc8xxx_spi->spi_remove = fsl_spi_remove;
ret = fsl_spi_cpm_init(mpc8xxx_spi);
if (ret)
goto err_cpm_init;
if (mpc8xxx_spi->flags & SPI_QE_CPU_MODE) {
mpc8xxx_spi->rx_shift = 16;
mpc8xxx_spi->tx_shift = 24;
}
mpc8xxx_spi->reg_base = ioremap(mem->start, resource_size(mem));
if (mpc8xxx_spi->reg_base == NULL) {
ret = -ENOMEM;
goto err_ioremap;
}
/* Register for SPI Interrupt */
ret = request_irq(mpc8xxx_spi->irq, fsl_spi_irq,
0, "fsl_spi", mpc8xxx_spi);
if (ret != 0)
goto free_irq;
reg_base = mpc8xxx_spi->reg_base;
/* SPI controller initializations */
mpc8xxx_spi_write_reg(&reg_base->mode, 0);
mpc8xxx_spi_write_reg(&reg_base->mask, 0);
mpc8xxx_spi_write_reg(&reg_base->command, 0);
mpc8xxx_spi_write_reg(&reg_base->event, 0xffffffff);
/* Enable SPI interface */
regval = pdata->initial_spmode | SPMODE_INIT_VAL | SPMODE_ENABLE;
if (mpc8xxx_spi->flags & SPI_QE_CPU_MODE)
regval |= SPMODE_OP;
mpc8xxx_spi_write_reg(&reg_base->mode, regval);
ret = spi_register_master(master);
if (ret < 0)
goto unreg_master;
dev_info(dev, "at 0x%p (irq = %d), %s mode\n", reg_base,
mpc8xxx_spi->irq, mpc8xxx_spi_strmode(mpc8xxx_spi->flags));
return master;
unreg_master:
free_irq(mpc8xxx_spi->irq, mpc8xxx_spi);
free_irq:
iounmap(mpc8xxx_spi->reg_base);
err_ioremap:
fsl_spi_cpm_free(mpc8xxx_spi);
err_cpm_init:
err_probe:
spi_master_put(master);
err:
return ERR_PTR(ret);
}
static void fsl_spi_cs_control(struct spi_device *spi, bool on)
{
struct device *dev = spi->dev.parent;
struct mpc8xxx_spi_probe_info *pinfo = to_of_pinfo(dev->platform_data);
u16 cs = spi->chip_select;
int gpio = pinfo->gpios[cs];
bool alow = pinfo->alow_flags[cs];
gpio_set_value(gpio, on ^ alow);
}
static int of_fsl_spi_get_chipselects(struct device *dev)
{
struct device_node *np = dev->of_node;
struct fsl_spi_platform_data *pdata = dev->platform_data;
struct mpc8xxx_spi_probe_info *pinfo = to_of_pinfo(pdata);
unsigned int ngpios;
int i = 0;
int ret;
ngpios = of_gpio_count(np);
if (!ngpios) {
/*
* SPI w/o chip-select line. One SPI device is still permitted
* though.
*/
pdata->max_chipselect = 1;
return 0;
}
pinfo->gpios = kmalloc(ngpios * sizeof(*pinfo->gpios), GFP_KERNEL);
if (!pinfo->gpios)
return -ENOMEM;
memset(pinfo->gpios, -1, ngpios * sizeof(*pinfo->gpios));
pinfo->alow_flags = kzalloc(ngpios * sizeof(*pinfo->alow_flags),
GFP_KERNEL);
if (!pinfo->alow_flags) {
ret = -ENOMEM;
goto err_alloc_flags;
}
for (; i < ngpios; i++) {
int gpio;
enum of_gpio_flags flags;
gpio = of_get_gpio_flags(np, i, &flags);
if (!gpio_is_valid(gpio)) {
dev_err(dev, "invalid gpio #%d: %d\n", i, gpio);
ret = gpio;
goto err_loop;
}
ret = gpio_request(gpio, dev_name(dev));
if (ret) {
dev_err(dev, "can't request gpio #%d: %d\n", i, ret);
goto err_loop;
}
pinfo->gpios[i] = gpio;
pinfo->alow_flags[i] = flags & OF_GPIO_ACTIVE_LOW;
ret = gpio_direction_output(pinfo->gpios[i],
pinfo->alow_flags[i]);
if (ret) {
dev_err(dev, "can't set output direction for gpio "
"#%d: %d\n", i, ret);
goto err_loop;
}
}
pdata->max_chipselect = ngpios;
pdata->cs_control = fsl_spi_cs_control;
return 0;
err_loop:
while (i >= 0) {
if (gpio_is_valid(pinfo->gpios[i]))
gpio_free(pinfo->gpios[i]);
i--;
}
kfree(pinfo->alow_flags);
pinfo->alow_flags = NULL;
err_alloc_flags:
kfree(pinfo->gpios);
pinfo->gpios = NULL;
return ret;
}
static int of_fsl_spi_free_chipselects(struct device *dev)
{
struct fsl_spi_platform_data *pdata = dev->platform_data;
struct mpc8xxx_spi_probe_info *pinfo = to_of_pinfo(pdata);
int i;
if (!pinfo->gpios)
return 0;
for (i = 0; i < pdata->max_chipselect; i++) {
if (gpio_is_valid(pinfo->gpios[i]))
gpio_free(pinfo->gpios[i]);
}
kfree(pinfo->gpios);
kfree(pinfo->alow_flags);
return 0;
}
static int __devinit of_fsl_spi_probe(struct platform_device *ofdev)
{
struct device *dev = &ofdev->dev;
struct device_node *np = ofdev->dev.of_node;
struct spi_master *master;
struct resource mem;
struct resource irq;
int ret = -ENOMEM;
ret = of_mpc8xxx_spi_probe(ofdev);
if (ret)
return ret;
ret = of_fsl_spi_get_chipselects(dev);
if (ret)
goto err;
ret = of_address_to_resource(np, 0, &mem);
if (ret)
goto err;
ret = of_irq_to_resource(np, 0, &irq);
if (!ret) {
ret = -EINVAL;
goto err;
}
master = fsl_spi_probe(dev, &mem, irq.start);
if (IS_ERR(master)) {
ret = PTR_ERR(master);
goto err;
}
return 0;
err:
of_fsl_spi_free_chipselects(dev);
return ret;
}
static int __devexit of_fsl_spi_remove(struct platform_device *ofdev)
{
int ret;
ret = mpc8xxx_spi_remove(&ofdev->dev);
if (ret)
return ret;
of_fsl_spi_free_chipselects(&ofdev->dev);
return 0;
}
static const struct of_device_id of_fsl_spi_match[] = {
{ .compatible = "fsl,spi" },
{}
};
MODULE_DEVICE_TABLE(of, of_fsl_spi_match);
static struct platform_driver of_fsl_spi_driver = {
.driver = {
.name = "fsl_spi",
.owner = THIS_MODULE,
.of_match_table = of_fsl_spi_match,
},
.probe = of_fsl_spi_probe,
.remove = __devexit_p(of_fsl_spi_remove),
};
#ifdef CONFIG_MPC832x_RDB
/*
* XXX XXX XXX
* This is "legacy" platform driver, was used by the MPC8323E-RDB boards
* only. The driver should go away soon, since newer MPC8323E-RDB's device
* tree can work with OpenFirmware driver. But for now we support old trees
* as well.
*/
static int __devinit plat_mpc8xxx_spi_probe(struct platform_device *pdev)
{
struct resource *mem;
int irq;
struct spi_master *master;
if (!pdev->dev.platform_data)
return -EINVAL;
mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!mem)
return -EINVAL;
irq = platform_get_irq(pdev, 0);
if (irq <= 0)
return -EINVAL;
master = fsl_spi_probe(&pdev->dev, mem, irq);
if (IS_ERR(master))
return PTR_ERR(master);
return 0;
}
static int __devexit plat_mpc8xxx_spi_remove(struct platform_device *pdev)
{
return mpc8xxx_spi_remove(&pdev->dev);
}
MODULE_ALIAS("platform:mpc8xxx_spi");
static struct platform_driver mpc8xxx_spi_driver = {
.probe = plat_mpc8xxx_spi_probe,
.remove = __devexit_p(plat_mpc8xxx_spi_remove),
.driver = {
.name = "mpc8xxx_spi",
.owner = THIS_MODULE,
},
};
static bool legacy_driver_failed;
static void __init legacy_driver_register(void)
{
legacy_driver_failed = platform_driver_register(&mpc8xxx_spi_driver);
}
static void __exit legacy_driver_unregister(void)
{
if (legacy_driver_failed)
return;
platform_driver_unregister(&mpc8xxx_spi_driver);
}
#else
static void __init legacy_driver_register(void) {}
static void __exit legacy_driver_unregister(void) {}
#endif /* CONFIG_MPC832x_RDB */
static int __init fsl_spi_init(void)
{
legacy_driver_register();
return platform_driver_register(&of_fsl_spi_driver);
}
module_init(fsl_spi_init);
static void __exit fsl_spi_exit(void)
{
platform_driver_unregister(&of_fsl_spi_driver);
legacy_driver_unregister();
}
module_exit(fsl_spi_exit);
MODULE_AUTHOR("Kumar Gala");
MODULE_DESCRIPTION("Simple Freescale SPI Driver");
MODULE_LICENSE("GPL");