renegade-project/linux-next
2
0
Fork 0
mirror of https://github.com/edk2-porting/linux-next.git synced 2024-12-28 23:23:55 +08:00
Code
828d055fd0
linux-next/drivers/net/ibm_emac/Kconfig

71 lines
1.5 KiB
Plaintext
Raw Normal View History

Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 11:56:01 +08:00
config IBM_EMAC
tristate "PowerPC 4xx on-chip Ethernet support"
depends on 4xx && !PPC_MERGE
help
This driver supports the PowerPC 4xx EMAC family of on-chip
Ethernet controllers.
config IBM_EMAC_RXB
int "Number of receive buffers"
depends on IBM_EMAC
default "128"
config IBM_EMAC_TXB
int "Number of transmit buffers"
depends on IBM_EMAC
default "64"
config IBM_EMAC_POLL_WEIGHT
int "MAL NAPI polling weight"
depends on IBM_EMAC
default "32"
config IBM_EMAC_RX_COPY_THRESHOLD
int "RX skb copy threshold (bytes)"
depends on IBM_EMAC
default "256"
config IBM_EMAC_RX_SKB_HEADROOM
int "Additional RX skb headroom (bytes)"
depends on IBM_EMAC
default "0"
help
Additional receive skb headroom. Note, that driver
will always reserve at least 2 bytes to make IP header
aligned, so usually there is no need to add any additional
headroom.
If unsure, set to 0.
config IBM_EMAC_PHY_RX_CLK_FIX
bool "PHY Rx clock workaround"
depends on IBM_EMAC && (405EP || 440GX || 440EP || 440GR)
help
Enable this if EMAC attached to a PHY which doesn't generate
RX clock if there is no link, if this is the case, you will
see "TX disable timeout" or "RX disable timeout" in the system
log.
If unsure, say N.
config IBM_EMAC_DEBUG
bool "Debugging"
depends on IBM_EMAC
default n
config IBM_EMAC_ZMII
bool
depends on IBM_EMAC && (NP405H || NP405L || 44x)
default y
config IBM_EMAC_RGMII
bool
depends on IBM_EMAC && 440GX
default y
config IBM_EMAC_TAH
bool
depends on IBM_EMAC && 440GX
default y
Copy Permalink