2
0
mirror of https://github.com/edk2-porting/linux-next.git synced 2024-12-28 15:13:55 +08:00
linux-next/arch/arm/mach-ixp4xx/common.c

685 lines
16 KiB
C
Raw Normal View History

/*
* arch/arm/mach-ixp4xx/common.c
*
* Generic code shared across all IXP4XX platforms
*
* Maintainer: Deepak Saxena <dsaxena@plexity.net>
*
* Copyright 2002 (c) Intel Corporation
* Copyright 2003-2004 (c) MontaVista, Software, Inc.
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
#include <linux/kernel.h>
#include <linux/mm.h>
#include <linux/init.h>
#include <linux/serial.h>
#include <linux/tty.h>
#include <linux/platform_device.h>
#include <linux/serial_core.h>
#include <linux/interrupt.h>
#include <linux/bitops.h>
#include <linux/time.h>
#include <linux/clocksource.h>
#include <linux/clockchips.h>
#include <linux/io.h>
#include <linux/export.h>
#include <linux/gpio/driver.h>
#include <linux/cpu.h>
#include <linux/pci.h>
#include <linux/sched_clock.h>
#include <mach/udc.h>
#include <mach/hardware.h>
#include <mach/io.h>
#include <linux/uaccess.h>
#include <asm/pgtable.h>
#include <asm/page.h>
#include <asm/irq.h>
#include <asm/system_misc.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
#include <asm/mach/time.h>
#define IXP4XX_TIMER_FREQ 66666000
ARM: ixp4xx: fix timer latch calculation In commit f0402f9b4711 ("ARM: ixp4xx: stop using <mach/timex.h>") I didn't intend to implement a functional change, but as Olof noticed I failed---at least a bit. Before this commit the following was used to determine the latch value used: #define IXP4XX_TIMER_FREQ 66666000 #define CLOCK_TICK_RATE \ (((IXP4XX_TIMER_FREQ / HZ & ~IXP4XX_OST_RELOAD_MASK) + 1) * HZ) #define LATCH ((CLOCK_TICK_RATE + HZ/2) / HZ) The complicated calculation was done "b/c the timer register ignores the bottom 2 bits of the LATCH value." With HZ=100 CLOCK_TICK_RATE used to calculate to 66666100 and so LATCH to 666661. In ixp4xx_set_mode the term LATCH & ~IXP4XX_OST_RELOAD_MASK was used to write to the relevant register (with IXP4XX_OST_RELOAD_MASK being 3) and so effectively 666660 was used. In commit f0402f9b4711 I translated that to: #define IXP4XX_TIMER_FREQ 66666000 #define IXP4XX_LATCH DIV_ROUND_CLOSEST(IXP4XX_TIMER_FREQ, HZ) which results in the same register writes, but still doesn't bear in mind that the two least significant bits cannot be specified (which is relevant only when HZ or IXP4XX_TIMER_FREQ are changed). Instead of reverting back to the old approach use a more obvious and also more correct way to calculate LATCH. (Regarding the more correct claim: With IXP4XX_TIMER_FREQ == 66665999, the old code resulted in LATCH = 666657 corresponding to a cycle time of 0.009999940149400597 seconds (error: -6.0e-8 s) while the new approach results in LATCH = 666660 and so a cycle time of 0.010000000150001503 seconds (error: 1.5e-10 s).) Fixes: f0402f9b4711 ("ARM: ixp4xx: stop using <mach/timex.h>") Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
2014-02-03 18:31:19 +08:00
/*
* The timer register doesn't allow to specify the two least significant bits of
* the timeout value and assumes them being zero. So make sure IXP4XX_LATCH is
* the best value with the two least significant bits unset.
*/
#define IXP4XX_LATCH DIV_ROUND_CLOSEST(IXP4XX_TIMER_FREQ, \
(IXP4XX_OST_RELOAD_MASK + 1) * HZ) * \
(IXP4XX_OST_RELOAD_MASK + 1)
static void __init ixp4xx_clocksource_init(void);
static void __init ixp4xx_clockevent_init(void);
static struct clock_event_device clockevent_ixp4xx;
/*************************************************************************
* IXP4xx chipset I/O mapping
*************************************************************************/
static struct map_desc ixp4xx_io_desc[] __initdata = {
{ /* UART, Interrupt ctrl, GPIO, timers, NPEs, MACs, USB .... */
.virtual = (unsigned long)IXP4XX_PERIPHERAL_BASE_VIRT,
.pfn = __phys_to_pfn(IXP4XX_PERIPHERAL_BASE_PHYS),
.length = IXP4XX_PERIPHERAL_REGION_SIZE,
.type = MT_DEVICE
}, { /* Expansion Bus Config Registers */
.virtual = (unsigned long)IXP4XX_EXP_CFG_BASE_VIRT,
.pfn = __phys_to_pfn(IXP4XX_EXP_CFG_BASE_PHYS),
.length = IXP4XX_EXP_CFG_REGION_SIZE,
.type = MT_DEVICE
}, { /* PCI Registers */
.virtual = (unsigned long)IXP4XX_PCI_CFG_BASE_VIRT,
.pfn = __phys_to_pfn(IXP4XX_PCI_CFG_BASE_PHYS),
.length = IXP4XX_PCI_CFG_REGION_SIZE,
.type = MT_DEVICE
}, { /* Queue Manager */
.virtual = (unsigned long)IXP4XX_QMGR_BASE_VIRT,
.pfn = __phys_to_pfn(IXP4XX_QMGR_BASE_PHYS),
.length = IXP4XX_QMGR_REGION_SIZE,
.type = MT_DEVICE
},
};
void __init ixp4xx_map_io(void)
{
iotable_init(ixp4xx_io_desc, ARRAY_SIZE(ixp4xx_io_desc));
}
/*
* GPIO-functions
*/
/*
* The following converted to the real HW bits the gpio_line_config
*/
/* GPIO pin types */
#define IXP4XX_GPIO_OUT 0x1
#define IXP4XX_GPIO_IN 0x2
/* GPIO signal types */
#define IXP4XX_GPIO_LOW 0
#define IXP4XX_GPIO_HIGH 1
/* GPIO Clocks */
#define IXP4XX_GPIO_CLK_0 14
#define IXP4XX_GPIO_CLK_1 15
static void gpio_line_config(u8 line, u32 direction)
{
if (direction == IXP4XX_GPIO_IN)
*IXP4XX_GPIO_GPOER |= (1 << line);
else
*IXP4XX_GPIO_GPOER &= ~(1 << line);
}
static void gpio_line_get(u8 line, int *value)
{
*value = (*IXP4XX_GPIO_GPINR >> line) & 0x1;
}
static void gpio_line_set(u8 line, int value)
{
if (value == IXP4XX_GPIO_HIGH)
*IXP4XX_GPIO_GPOUTR |= (1 << line);
else if (value == IXP4XX_GPIO_LOW)
*IXP4XX_GPIO_GPOUTR &= ~(1 << line);
}
/*************************************************************************
* IXP4xx chipset IRQ handling
*
* TODO: GPIO IRQs should be marked invalid until the user of the IRQ
* (be it PCI or something else) configures that GPIO line
* as an IRQ.
**************************************************************************/
enum ixp4xx_irq_type {
IXP4XX_IRQ_LEVEL, IXP4XX_IRQ_EDGE
};
/* Each bit represents an IRQ: 1: edge-triggered, 0: level triggered */
static unsigned long long ixp4xx_irq_edge = 0;
/*
* IRQ -> GPIO mapping table
*/
static signed char irq2gpio[32] = {
-1, -1, -1, -1, -1, -1, 0, 1,
-1, -1, -1, -1, -1, -1, -1, -1,
-1, -1, -1, 2, 3, 4, 5, 6,
7, 8, 9, 10, 11, 12, -1, -1,
};
static int ixp4xx_gpio_to_irq(struct gpio_chip *chip, unsigned gpio)
{
int irq;
for (irq = 0; irq < 32; irq++) {
if (irq2gpio[irq] == gpio)
return irq;
}
return -EINVAL;
}
static int ixp4xx_set_irq_type(struct irq_data *d, unsigned int type)
{
int line = irq2gpio[d->irq];
u32 int_style;
enum ixp4xx_irq_type irq_type;
volatile u32 *int_reg;
/*
* Only for GPIO IRQs
*/
if (line < 0)
return -EINVAL;
switch (type){
case IRQ_TYPE_EDGE_BOTH:
int_style = IXP4XX_GPIO_STYLE_TRANSITIONAL;
irq_type = IXP4XX_IRQ_EDGE;
break;
case IRQ_TYPE_EDGE_RISING:
int_style = IXP4XX_GPIO_STYLE_RISING_EDGE;
irq_type = IXP4XX_IRQ_EDGE;
break;
case IRQ_TYPE_EDGE_FALLING:
int_style = IXP4XX_GPIO_STYLE_FALLING_EDGE;
irq_type = IXP4XX_IRQ_EDGE;
break;
case IRQ_TYPE_LEVEL_HIGH:
int_style = IXP4XX_GPIO_STYLE_ACTIVE_HIGH;
irq_type = IXP4XX_IRQ_LEVEL;
break;
case IRQ_TYPE_LEVEL_LOW:
int_style = IXP4XX_GPIO_STYLE_ACTIVE_LOW;
irq_type = IXP4XX_IRQ_LEVEL;
break;
default:
return -EINVAL;
}
if (irq_type == IXP4XX_IRQ_EDGE)
ixp4xx_irq_edge |= (1 << d->irq);
else
ixp4xx_irq_edge &= ~(1 << d->irq);
if (line >= 8) { /* pins 8-15 */
line -= 8;
int_reg = IXP4XX_GPIO_GPIT2R;
} else { /* pins 0-7 */
int_reg = IXP4XX_GPIO_GPIT1R;
}
/* Clear the style for the appropriate pin */
*int_reg &= ~(IXP4XX_GPIO_STYLE_CLEAR <<
(line * IXP4XX_GPIO_STYLE_SIZE));
*IXP4XX_GPIO_GPISR = (1 << line);
/* Set the new style */
*int_reg |= (int_style << (line * IXP4XX_GPIO_STYLE_SIZE));
/* Configure the line as an input */
gpio_line_config(irq2gpio[d->irq], IXP4XX_GPIO_IN);
return 0;
}
static void ixp4xx_irq_mask(struct irq_data *d)
{
if ((cpu_is_ixp46x() || cpu_is_ixp43x()) && d->irq >= 32)
*IXP4XX_ICMR2 &= ~(1 << (d->irq - 32));
else
*IXP4XX_ICMR &= ~(1 << d->irq);
}
static void ixp4xx_irq_ack(struct irq_data *d)
{
int line = (d->irq < 32) ? irq2gpio[d->irq] : -1;
if (line >= 0)
*IXP4XX_GPIO_GPISR = (1 << line);
}
/*
* Level triggered interrupts on GPIO lines can only be cleared when the
* interrupt condition disappears.
*/
static void ixp4xx_irq_unmask(struct irq_data *d)
{
if (!(ixp4xx_irq_edge & (1 << d->irq)))
ixp4xx_irq_ack(d);
if ((cpu_is_ixp46x() || cpu_is_ixp43x()) && d->irq >= 32)
*IXP4XX_ICMR2 |= (1 << (d->irq - 32));
else
*IXP4XX_ICMR |= (1 << d->irq);
}
static struct irq_chip ixp4xx_irq_chip = {
.name = "IXP4xx",
.irq_ack = ixp4xx_irq_ack,
.irq_mask = ixp4xx_irq_mask,
.irq_unmask = ixp4xx_irq_unmask,
.irq_set_type = ixp4xx_set_irq_type,
};
void __init ixp4xx_init_irq(void)
{
int i = 0;
/*
* ixp4xx does not implement the XScale PWRMODE register
* so it must not call cpu_do_idle().
*/
cpu_idle_poll_ctrl(true);
/* Route all sources to IRQ instead of FIQ */
*IXP4XX_ICLR = 0x0;
/* Disable all interrupt */
*IXP4XX_ICMR = 0x0;
if (cpu_is_ixp46x() || cpu_is_ixp43x()) {
/* Route upper 32 sources to IRQ instead of FIQ */
*IXP4XX_ICLR2 = 0x00;
/* Disable upper 32 interrupts */
*IXP4XX_ICMR2 = 0x00;
}
/* Default to all level triggered */
for(i = 0; i < NR_IRQS; i++) {
irq_set_chip_and_handler(i, &ixp4xx_irq_chip,
handle_level_irq);
ARM: kill off set_irq_flags usage set_irq_flags is ARM specific with custom flags which have genirq equivalents. Convert drivers to use the genirq interfaces directly, so we can kill off set_irq_flags. The translation of flags is as follows: IRQF_VALID -> !IRQ_NOREQUEST IRQF_PROBE -> !IRQ_NOPROBE IRQF_NOAUTOEN -> IRQ_NOAUTOEN For IRQs managed by an irqdomain, the irqdomain core code handles clearing and setting IRQ_NOREQUEST already, so there is no need to do this in .map() functions and we can simply remove the set_irq_flags calls. Some users also modify IRQ_NOPROBE and this has been maintained although it is not clear that is really needed. There appears to be a great deal of blind copy and paste of this code. Signed-off-by: Rob Herring <robh@kernel.org> Cc: Russell King <linux@arm.linux.org.uk> Cc: Sekhar Nori <nsekhar@ti.com> Cc: Kevin Hilman <khilman@deeprootsystems.com> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Cc: Gregory Clement <gregory.clement@free-electrons.com> Acked-by: Hans Ulli Kroll <ulli.kroll@googlemail.com> Acked-by: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <kernel@pengutronix.de> Cc: Imre Kaloz <kaloz@openwrt.org> Acked-by: Krzysztof Halasa <khalasa@piap.pl> Cc: Greg Ungerer <gerg@uclinux.org> Cc: Roland Stigge <stigge@antcom.de> Cc: Tony Lindgren <tony@atomide.com> Cc: Daniel Mack <daniel@zonque.org> Cc: Haojian Zhuang <haojian.zhuang@gmail.com> Cc: Robert Jarzmik <robert.jarzmik@free.fr> Cc: Simtec Linux Team <linux@simtec.co.uk> Cc: Kukjin Kim <kgene@kernel.org> Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com> Acked-by: Wan ZongShun <mcuos.com@gmail.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-omap@vger.kernel.org Cc: linux-samsung-soc@vger.kernel.org Tested-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
2015-07-28 04:55:13 +08:00
irq_clear_status_flags(i, IRQ_NOREQUEST);
}
}
/*************************************************************************
* IXP4xx timer tick
* We use OS timer1 on the CPU for the timer tick and the timestamp
* counter as a source of real clock ticks to account for missed jiffies.
*************************************************************************/
static irqreturn_t ixp4xx_timer_interrupt(int irq, void *dev_id)
{
struct clock_event_device *evt = dev_id;
/* Clear Pending Interrupt by writing '1' to it */
*IXP4XX_OSST = IXP4XX_OSST_TIMER_1_PEND;
evt->event_handler(evt);
return IRQ_HANDLED;
}
static struct irqaction ixp4xx_timer_irq = {
.name = "timer1",
.flags = IRQF_TIMER | IRQF_IRQPOLL,
.handler = ixp4xx_timer_interrupt,
.dev_id = &clockevent_ixp4xx,
};
void __init ixp4xx_timer_init(void)
{
/* Reset/disable counter */
*IXP4XX_OSRT1 = 0;
/* Clear Pending Interrupt by writing '1' to it */
*IXP4XX_OSST = IXP4XX_OSST_TIMER_1_PEND;
/* Reset time-stamp counter */
*IXP4XX_OSTS = 0;
/* Connect the interrupt handler and enable the interrupt */
setup_irq(IRQ_IXP4XX_TIMER1, &ixp4xx_timer_irq);
ixp4xx_clocksource_init();
ixp4xx_clockevent_init();
}
static struct pxa2xx_udc_mach_info ixp4xx_udc_info;
void __init ixp4xx_set_udc_info(struct pxa2xx_udc_mach_info *info)
{
memcpy(&ixp4xx_udc_info, info, sizeof *info);
}
static struct resource ixp4xx_udc_resources[] = {
[0] = {
.start = 0xc800b000,
.end = 0xc800bfff,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = IRQ_IXP4XX_USB,
.end = IRQ_IXP4XX_USB,
.flags = IORESOURCE_IRQ,
},
};
/*
* USB device controller. The IXP4xx uses the same controller as PXA25X,
* so we just use the same device.
*/
static struct platform_device ixp4xx_udc_device = {
.name = "pxa25x-udc",
.id = -1,
.num_resources = 2,
.resource = ixp4xx_udc_resources,
.dev = {
.platform_data = &ixp4xx_udc_info,
},
};
static struct platform_device *ixp4xx_devices[] __initdata = {
&ixp4xx_udc_device,
};
static struct resource ixp46x_i2c_resources[] = {
[0] = {
.start = 0xc8011000,
.end = 0xc801101c,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = IRQ_IXP4XX_I2C,
.end = IRQ_IXP4XX_I2C,
.flags = IORESOURCE_IRQ
}
};
/*
* I2C controller. The IXP46x uses the same block as the IOP3xx, so
* we just use the same device name.
*/
static struct platform_device ixp46x_i2c_controller = {
.name = "IOP3xx-I2C",
.id = 0,
.num_resources = 2,
.resource = ixp46x_i2c_resources
};
static struct platform_device *ixp46x_devices[] __initdata = {
&ixp46x_i2c_controller
};
unsigned long ixp4xx_exp_bus_size;
EXPORT_SYMBOL(ixp4xx_exp_bus_size);
static int ixp4xx_gpio_direction_input(struct gpio_chip *chip, unsigned gpio)
{
gpio_line_config(gpio, IXP4XX_GPIO_IN);
return 0;
}
static int ixp4xx_gpio_direction_output(struct gpio_chip *chip, unsigned gpio,
int level)
{
gpio_line_set(gpio, level);
gpio_line_config(gpio, IXP4XX_GPIO_OUT);
return 0;
}
static int ixp4xx_gpio_get_value(struct gpio_chip *chip, unsigned gpio)
{
int value;
gpio_line_get(gpio, &value);
return value;
}
static void ixp4xx_gpio_set_value(struct gpio_chip *chip, unsigned gpio,
int value)
{
gpio_line_set(gpio, value);
}
static struct gpio_chip ixp4xx_gpio_chip = {
.label = "IXP4XX_GPIO_CHIP",
.direction_input = ixp4xx_gpio_direction_input,
.direction_output = ixp4xx_gpio_direction_output,
.get = ixp4xx_gpio_get_value,
.set = ixp4xx_gpio_set_value,
.to_irq = ixp4xx_gpio_to_irq,
.base = 0,
.ngpio = 16,
};
void __init ixp4xx_sys_init(void)
{
ixp4xx_exp_bus_size = SZ_16M;
platform_add_devices(ixp4xx_devices, ARRAY_SIZE(ixp4xx_devices));
gpiochip_add_data(&ixp4xx_gpio_chip, NULL);
if (cpu_is_ixp46x()) {
int region;
platform_add_devices(ixp46x_devices,
ARRAY_SIZE(ixp46x_devices));
for (region = 0; region < 7; region++) {
if((*(IXP4XX_EXP_REG(0x4 * region)) & 0x200)) {
ixp4xx_exp_bus_size = SZ_32M;
break;
}
}
}
printk("IXP4xx: Using %luMiB expansion bus window size\n",
ixp4xx_exp_bus_size >> 20);
}
/*
* sched_clock()
*/
static u64 notrace ixp4xx_read_sched_clock(void)
{
ARM: 7205/2: sched_clock: allow sched_clock to be selected at runtime sched_clock() is yet another blocker on the road to the single image. This patch implements an idea by Russell King: http://www.spinics.net/lists/linux-omap/msg49561.html Instead of asking the platform to implement both sched_clock() itself and the rollover callback, simply register a read() function, and let the ARM code care about sched_clock() itself, the conversion to ns and the rollover. sched_clock() uses this read() function as an indirection to the platform code. If the platform doesn't provide a read(), the code falls back to the jiffy counter (just like the default sched_clock). This allow some simplifications and possibly some footprint gain when multiple platforms are compiled in. Among the drawbacks, the removal of the *_fixed_sched_clock optimization which could negatively impact some platforms (sa1100, tegra, versatile and omap). Tested on 11MPCore, OMAP4 and Tegra. Cc: Imre Kaloz <kaloz@openwrt.org> Cc: Eric Miao <eric.y.miao@gmail.com> Cc: Colin Cross <ccross@android.com> Cc: Erik Gilling <konkers@android.com> Cc: Olof Johansson <olof@lixom.net> Cc: Sascha Hauer <kernel@pengutronix.de> Cc: Alessandro Rubini <rubini@unipv.it> Cc: STEricsson <STEricsson_nomadik_linux@list.st.com> Cc: Lennert Buytenhek <kernel@wantstofly.org> Cc: Ben Dooks <ben-linux@fluff.org> Tested-by: Jamie Iles <jamie@jamieiles.com> Tested-by: Tony Lindgren <tony@atomide.com> Tested-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Nicolas Pitre <nico@linaro.org> Acked-by: Krzysztof Halasa <khc@pm.waw.pl> Acked-by: Kukjin Kim <kgene.kim@samsung.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-12-15 19:19:23 +08:00
return *IXP4XX_OSTS;
}
/*
* clocksource
*/
static u64 ixp4xx_clocksource_read(struct clocksource *c)
{
return *IXP4XX_OSTS;
}
unsigned long ixp4xx_timer_freq = IXP4XX_TIMER_FREQ;
IXP42x HSS support for setting internal clock rate HSS usually uses external clocks, so it's not a big deal. Internal clock is used for direct DTE-DTE connections and when the DCE doesn't provide it's own clock. This also depends on the oscillator frequency. Intel seems to have calculated the clock register settings for 33.33 MHz (66.66 MHz timer base). Their settings seem quite suboptimal both in terms of average frequency (60 ppm is unacceptable for G.703 applications, their primary intended usage(?)) and jitter. Many (most?) platforms use a 33.333 MHz oscillator, a 10 ppm difference from Intel's base. Instead of creating static tables, I've created a procedure to program the HSS clock register. The register consists of 3 parts (A, B, C). The average frequency (= bit rate) is: 66.66x MHz / (A + (B + 1) / (C + 1)) The procedure aims at the closest average frequency, possibly at the cost of increased jitter. Nobody would be able to directly drive an unbufferred transmitter with a HSS anyway, and the frequency error is what it really counts. I've verified the above with an oscilloscope on IXP425. It seems IXP46x and possibly IXP43x use a bit different clock generation algorithm - it looks like the avg frequency is: (on IXP465) 66.66x MHz / (A + B / (C + 1)). Also they use much greater precomputed A and B - on IXP425 it would simply result in more jitter, but I don't know how does it work on IXP46x (perhaps 3 least significant bits aren't used?). Anyway it looks that they were aiming for exactly +60 ppm or -60 ppm, while <1 ppm is typically possible (with a synchronized clock, of course). The attached patch makes it possible to set almost any bit rate (my IXP425 533 MHz quits at > 22 Mb/s if a single port is used, and the minimum is ca. 65 Kb/s). This is independent of MVIP (multi-E1/T1 on one HSS) mode. Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-05 11:59:49 +08:00
EXPORT_SYMBOL(ixp4xx_timer_freq);
static void __init ixp4xx_clocksource_init(void)
{
sched_clock_register(ixp4xx_read_sched_clock, 32, ixp4xx_timer_freq);
clocksource_mmio_init(NULL, "OSTS", ixp4xx_timer_freq, 200, 32,
ixp4xx_clocksource_read);
}
/*
* clockevents
*/
static int ixp4xx_set_next_event(unsigned long evt,
struct clock_event_device *unused)
{
unsigned long opts = *IXP4XX_OSRT1 & IXP4XX_OST_RELOAD_MASK;
*IXP4XX_OSRT1 = (evt & ~IXP4XX_OST_RELOAD_MASK) | opts;
return 0;
}
static int ixp4xx_shutdown(struct clock_event_device *evt)
{
unsigned long opts = *IXP4XX_OSRT1 & IXP4XX_OST_RELOAD_MASK;
unsigned long osrt = *IXP4XX_OSRT1 & ~IXP4XX_OST_RELOAD_MASK;
opts &= ~IXP4XX_OST_ENABLE;
*IXP4XX_OSRT1 = osrt | opts;
return 0;
}
static int ixp4xx_set_oneshot(struct clock_event_device *evt)
{
unsigned long opts = IXP4XX_OST_ENABLE | IXP4XX_OST_ONE_SHOT;
unsigned long osrt = 0;
/* period set by 'set next_event' */
*IXP4XX_OSRT1 = osrt | opts;
return 0;
}
static int ixp4xx_set_periodic(struct clock_event_device *evt)
{
unsigned long opts = IXP4XX_OST_ENABLE;
unsigned long osrt = IXP4XX_LATCH & ~IXP4XX_OST_RELOAD_MASK;
*IXP4XX_OSRT1 = osrt | opts;
return 0;
}
static int ixp4xx_resume(struct clock_event_device *evt)
{
unsigned long opts = *IXP4XX_OSRT1 & IXP4XX_OST_RELOAD_MASK;
unsigned long osrt = *IXP4XX_OSRT1 & ~IXP4XX_OST_RELOAD_MASK;
opts |= IXP4XX_OST_ENABLE;
*IXP4XX_OSRT1 = osrt | opts;
return 0;
}
static struct clock_event_device clockevent_ixp4xx = {
.name = "ixp4xx timer1",
.features = CLOCK_EVT_FEAT_PERIODIC |
CLOCK_EVT_FEAT_ONESHOT,
.rating = 200,
.set_state_shutdown = ixp4xx_shutdown,
.set_state_periodic = ixp4xx_set_periodic,
.set_state_oneshot = ixp4xx_set_oneshot,
.tick_resume = ixp4xx_resume,
.set_next_event = ixp4xx_set_next_event,
};
static void __init ixp4xx_clockevent_init(void)
{
clockevent_ixp4xx.cpumask = cpumask_of(0);
clockevents_config_and_register(&clockevent_ixp4xx, IXP4XX_TIMER_FREQ,
0xf, 0xfffffffe);
}
void ixp4xx_restart(enum reboot_mode mode, const char *cmd)
{
if (mode == REBOOT_SOFT) {
/* Jump into ROM at address 0 */
soft_restart(0);
} else {
/* Use on-chip reset capability */
/* set the "key" register to enable access to
* "timer" and "enable" registers
*/
*IXP4XX_OSWK = IXP4XX_WDT_KEY;
/* write 0 to the timer register for an immediate reset */
*IXP4XX_OSWT = 0;
*IXP4XX_OSWE = IXP4XX_WDT_RESET_ENABLE | IXP4XX_WDT_COUNT_ENABLE;
}
}
#ifdef CONFIG_PCI
static int ixp4xx_needs_bounce(struct device *dev, dma_addr_t dma_addr, size_t size)
{
return (dma_addr + size) > SZ_64M;
}
static int ixp4xx_platform_notify_remove(struct device *dev)
{
if (dev_is_pci(dev))
dmabounce_unregister_dev(dev);
return 0;
}
#endif
/*
* Setup DMA mask to 64MB on PCI devices and 4 GB on all other things.
*/
static int ixp4xx_platform_notify(struct device *dev)
{
dev->dma_mask = &dev->coherent_dma_mask;
#ifdef CONFIG_PCI
if (dev_is_pci(dev)) {
dev->coherent_dma_mask = DMA_BIT_MASK(28); /* 64 MB */
dmabounce_register_dev(dev, 2048, 4096, ixp4xx_needs_bounce);
return 0;
}
#endif
dev->coherent_dma_mask = DMA_BIT_MASK(32);
return 0;
}
int dma_set_coherent_mask(struct device *dev, u64 mask)
{
if (dev_is_pci(dev))
mask &= DMA_BIT_MASK(28); /* 64 MB */
if ((mask & DMA_BIT_MASK(28)) == DMA_BIT_MASK(28)) {
dev->coherent_dma_mask = mask;
return 0;
}
return -EIO; /* device wanted sub-64MB mask */
}
EXPORT_SYMBOL(dma_set_coherent_mask);
#ifdef CONFIG_IXP4XX_INDIRECT_PCI
/*
* In the case of using indirect PCI, we simply return the actual PCI
* address and our read/write implementation use that to drive the
* access registers. If something outside of PCI is ioremap'd, we
* fallback to the default.
*/
static void __iomem *ixp4xx_ioremap_caller(phys_addr_t addr, size_t size,
unsigned int mtype, void *caller)
{
if (!is_pci_memory(addr))
return __arm_ioremap_caller(addr, size, mtype, caller);
return (void __iomem *)addr;
}
static void ixp4xx_iounmap(volatile void __iomem *addr)
{
if (!is_pci_memory((__force u32)addr))
__iounmap(addr);
}
#endif
void __init ixp4xx_init_early(void)
{
platform_notify = ixp4xx_platform_notify;
#ifdef CONFIG_PCI
platform_notify_remove = ixp4xx_platform_notify_remove;
#endif
#ifdef CONFIG_IXP4XX_INDIRECT_PCI
arch_ioremap_caller = ixp4xx_ioremap_caller;
arch_iounmap = ixp4xx_iounmap;
#endif
}