mirror of
https://github.com/u-boot/u-boot.git
synced 2024-12-02 09:03:27 +08:00
b05cebb5f2
All i.MX8MQ boards have been converted to binman, which makes it
necessary to flash both flash.bin and u-boot.itb to get a bootable
system. Prior to the conversion, only flash.bin was needed.
Such new requirement breaks existing distro mechanisms to generate the
final binary because the extra u-boot.itb is now required.
Generate a final flash.bin that can be used again as a single bootable
binary to keep the original behavior.
After this change the SPL binary is called spl.bin, which is a more
descriptive name for its purpose, and can still be used standalone (for
example, for secure boot purposes).
Also update imx8mq_evk.rst to remove the u-boot.itb copy step.
This is a cherry-pick of 028abfd9b1 ("imx8mm-evk: Generate a single
bootable flash.bin again") adjusted to apply to i.MX8MQ.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Fabio Estevam <festevam@denx.de>
57 lines
1.2 KiB
ReStructuredText
57 lines
1.2 KiB
ReStructuredText
.. SPDX-License-Identifier: GPL-2.0+
|
|
|
|
imx8mq_evk
|
|
==========
|
|
|
|
U-Boot for the NXP i.MX8MQ EVK board
|
|
|
|
Quick Start
|
|
-----------
|
|
|
|
- Build the ARM Trusted firmware binary
|
|
- Get ddr and hdmi fimware
|
|
- Build U-Boot
|
|
- Boot
|
|
|
|
Get and Build the ARM Trusted firmware
|
|
--------------------------------------
|
|
|
|
Note: srctree is U-Boot source directory
|
|
Get ATF from: https://source.codeaurora.org/external/imx/imx-atf
|
|
branch: imx_5.4.47_2.2.0
|
|
|
|
.. code-block:: bash
|
|
|
|
$ make PLAT=imx8mq bl31
|
|
$ cp build/imx8mq/release/bl31.bin $(builddir)
|
|
|
|
Get the ddr and hdmi firmware
|
|
-----------------------------
|
|
|
|
.. code-block:: bash
|
|
|
|
$ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.9.bin
|
|
$ chmod +x firmware-imx-8.9.bin
|
|
$ ./firmware-imx-8.9.bin
|
|
$ cp firmware-imx-8.9/firmware/hdmi/cadence/signed_hdmi_imx8m.bin $(builddir)
|
|
$ cp firmware-imx-8.9/firmware/ddr/synopsys/lpddr4*.bin $(builddir)
|
|
|
|
Build U-Boot
|
|
------------
|
|
|
|
.. code-block:: bash
|
|
|
|
$ export CROSS_COMPILE=aarch64-poky-linux-
|
|
$ make imx8mq_evk_defconfig
|
|
$ make
|
|
|
|
Burn the flash.bin to MicroSD card offset 33KB:
|
|
|
|
.. code-block:: bash
|
|
|
|
$sudo dd if=flash.bin of=/dev/sd[x] bs=1024 seek=33 conv=notrunc
|
|
|
|
Boot
|
|
----
|
|
Set Boot switch SW801: 1100 and Bmode: 10 to boot from Micro SD.
|