u-boot/include/configs/ls1021aiot.h
Tom Rini f76750d111 Convert CONFIG_CONS_INDEX et al to Kconfig
This converts the following to Kconfig:
   CONFIG_CONS_INDEX
   CONFIG_DEBUG_UART_CLOCK
   CONFIG_FSL_TZPC_BP147
   CONFIG_GENERIC_ATMEL_MCI
   CONFIG_IDENT_STRING
   CONFIG_LIBATA
   CONFIG_LNX_KRNL_IMG_TEXT_OFFSET_BASE
   CONFIG_LPC32XX_GPIO
   CONFIG_MP
   CONFIG_MPC8XXX_GPIO
   CONFIG_MTD_PARTITIONS
   CONFIG_MVGBE
   CONFIG_MXC_GPIO
   CONFIG_NR_DRAM_BANKS
   CONFIG_OF_BOARD_SETUP
   CONFIG_OF_STDOUT_VIA_ALIAS
   CONFIG_OF_SYSTEM_SETUP
   CONFIG_PREBOOT
   CONFIG_ROCKCHIP_SERIAL
   CONFIG_RTC_ENABLE_32KHZ_OUTPUT
   CONFIG_RTC_MV
   CONFIG_SCSI_AHCI
   CONFIG_SF_DEFAULT_BUS
   CONFIG_SF_DEFAULT_CS
   CONFIG_SF_DEFAULT_SPEED
   CONFIG_SOFT_SPI
   CONFIG_SPI_FLASH_EON
   CONFIG_SPI_FLASH_MACRONIX
   CONFIG_SPI_FLASH_MTD
   CONFIG_SPI_FLASH_SPANSION
   CONFIG_SPI_FLASH_SST
   CONFIG_SPI_FLASH_STMICRO
   CONFIG_SUPPORT_RAW_INITRD
   CONFIG_SYS_ARCH_TIMER
   CONFIG_SYS_BOARD
   CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
   CONFIG_SYS_DCACHE_OFF
   CONFIG_SYS_FDT_SAVE_ADDRESS
   CONFIG_SYS_FLASH_CFI
   CONFIG_SYS_FSL_ERRATUM_ESDHC135
   CONFIG_SYS_HAS_SERDES
   CONFIG_SYS_L2CACHE_OFF
   CONFIG_SYS_LITTLE_ENDIAN
   CONFIG_SYS_LOAD_ADDR
   CONFIG_SYS_MMCSD_FS_BOOT_PARTITION
   CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION
   CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR
   CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
   CONFIG_SYS_NS16550
   CONFIG_SYS_PLLFIN
   CONFIG_SYS_SPI_U_BOOT_OFFS
   CONFIG_TIMER_SYS_TICK_CH
   CONFIG_USB_EHCI_FSL
   CONFIG_U_QE
   CONFIG_VERSION_VARIABLE

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-12-27 08:41:38 -05:00

175 lines
4.1 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2016 Freescale Semiconductor, Inc.
* Copyright 2019 NXP
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#define CONFIG_ARMV7_SECURE_BASE OCRAM_BASE_S_ADDR
#define CONFIG_SYS_FSL_CLK
#define CONFIG_SYS_INIT_RAM_ADDR OCRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE OCRAM_SIZE
#define CONFIG_SYS_CLK_FREQ 100000000
/*
* DDR: 800 MHz ( 1600 MT/s data rate )
*/
#define DDR_SDRAM_CFG 0x470c0008
#define DDR_CS0_BNDS 0x008000bf
#define DDR_CS0_CONFIG 0x80014302
#define DDR_TIMING_CFG_0 0x50550004
#define DDR_TIMING_CFG_1 0xbcb38c56
#define DDR_TIMING_CFG_2 0x0040d120
#define DDR_TIMING_CFG_3 0x010e1000
#define DDR_TIMING_CFG_4 0x00000001
#define DDR_TIMING_CFG_5 0x03401400
#define DDR_SDRAM_CFG_2 0x00401010
#define DDR_SDRAM_MODE 0x00061c60
#define DDR_SDRAM_MODE_2 0x00180000
#define DDR_SDRAM_INTERVAL 0x18600618
#define DDR_DDR_WRLVL_CNTL 0x8655f605
#define DDR_DDR_WRLVL_CNTL_2 0x05060607
#define DDR_DDR_WRLVL_CNTL_3 0x05050505
#define DDR_DDR_CDR1 0x80040000
#define DDR_DDR_CDR2 0x00000001
#define DDR_SDRAM_CLK_CNTL 0x02000000
#define DDR_DDR_ZQ_CNTL 0x89080600
#define DDR_CS0_CONFIG_2 0
#define DDR_SDRAM_CFG_MEM_EN 0x80000000
#define SDRAM_CFG2_D_INIT 0x00000010
#define DDR_CDR2_VREF_TRAIN_EN 0x00000080
#define SDRAM_CFG2_FRC_SR 0x80000000
#define SDRAM_CFG_BI 0x00000001
#ifdef CONFIG_SD_BOOT
#define CONFIG_SPL_MAX_SIZE 0x1a000
#define CONFIG_SPL_STACK 0x1001d000
#define CONFIG_SPL_PAD_TO 0x1c000
#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE + \
CONFIG_SYS_MONITOR_LEN)
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
#define CONFIG_SPL_BSS_START_ADDR 0x80100000
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
#define CONFIG_SYS_MONITOR_LEN 0x80000
#endif
#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_CHIP_SELECTS_PER_CTRL 4
/*
* Serial Port
*/
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_serial_clock()
/*
* I2C
*/
/* EEPROM */
#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_SYS_EEPROM_BUS_NUM 0
/*
* MMC
*/
/* SATA */
#define CONFIG_SCSI_AHCI_PLAT
#ifndef PCI_DEVICE_ID_FREESCALE_AHCI
#define PCI_DEVICE_ID_FREESCALE_AHCI 0x0440
#endif
#define CONFIG_SCSI_DEV_LIST {PCI_VENDOR_ID_FREESCALE, \
PCI_DEVICE_ID_FREESCALE_AHCI}
#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
#define CONFIG_SYS_SCSI_MAX_LUN 1
#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
CONFIG_SYS_SCSI_MAX_LUN)
/* SPI */
/*
* eTSEC
*/
#ifdef CONFIG_TSEC_ENET
#define CONFIG_MII_DEFAULT_TSEC 1
#define CONFIG_TSEC1 1
#define CONFIG_TSEC1_NAME "eTSEC1"
#define CONFIG_TSEC2 1
#define CONFIG_TSEC2_NAME "eTSEC2"
#define TSEC1_PHY_ADDR 1
#define TSEC2_PHY_ADDR 3
#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
#define CONFIG_ETHPRIME "eTSEC2"
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#define CONFIG_HAS_ETH2
#endif
/* PCIe */
#define CONFIG_PCIE1 /* PCIE controler 1 */
#define CONFIG_PCIE2 /* PCIE controler 2 */
#define FSL_PCIE_COMPAT "fsl,ls1021a-pcie"
#ifdef CONFIG_PCI
#define CONFIG_PCI_SCAN_SHOW
#endif
#define CONFIG_PEN_ADDR_BIG_ENDIAN
#define CONFIG_LAYERSCAPE_NS_ACCESS
#define CONFIG_SMP_PEN_ADDR 0x01ee0200
#define COUNTER_FREQUENCY 12500000
#define CONFIG_HWCONFIG
#define HWCONFIG_BUFFER_SIZE 256
#define CONFIG_FSL_DEVICE_DISABLE
#define CONFIG_EXTRA_ENV_SETTINGS \
"bootargs=root=/dev/ram0 rw console=ttyS0,115200\0" \
"initrd_high=0xffffffff\0"
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_BOOTMAPSZ (256 << 20)
#define CONFIG_LS102XA_STREAM_ID
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
#else
/* start of monitor */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#endif
#include <asm/fsl_secure_boot.h>
#endif