mirror of
https://github.com/u-boot/u-boot.git
synced 2024-12-27 21:53:25 +08:00
f232950f82
Remove platform CONFIG_SYS_HZ definition for configs a-z*. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
486 lines
16 KiB
C
486 lines
16 KiB
C
/*
|
|
* (C) Copyright 2000-2004
|
|
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
/*
|
|
* Dan Malek, Embedded Edge, LLC, dan@embeddededge.com
|
|
* U-Boot port on STx XTc 8xx board
|
|
* Mostly copied from Panto's NETTA2 board.
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
* (easy to change)
|
|
*/
|
|
|
|
#define CONFIG_MPC875 1 /* This is a MPC875 CPU */
|
|
#define CONFIG_STXXTC 1 /* ...on a STx XTc board */
|
|
|
|
#define CONFIG_SYS_TEXT_BASE 0x40F00000
|
|
|
|
#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
|
|
#undef CONFIG_8xx_CONS_SMC2
|
|
#undef CONFIG_8xx_CONS_NONE
|
|
|
|
#define CONFIG_BAUDRATE 115200 /* console baudrate = 115.2kbps */
|
|
|
|
#define CONFIG_XIN 10000000 /* 10 MHz input xtal */
|
|
|
|
/* Select one of few clock rates defined later in this file.
|
|
*/
|
|
/* #define MPC8XX_HZ 50000000 */
|
|
#define MPC8XX_HZ 66666666
|
|
|
|
#define CONFIG_8xx_GCLK_FREQ MPC8XX_HZ
|
|
|
|
#if 0
|
|
#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
|
|
#else
|
|
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
|
|
#endif
|
|
|
|
#undef CONFIG_CLOCKS_IN_MHZ /* clocks NOT passsed to Linux in MHz */
|
|
|
|
#undef CONFIG_BOOTARGS
|
|
#define CONFIG_BOOTCOMMAND \
|
|
"tftpboot; " \
|
|
"setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
|
|
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \
|
|
"bootm"
|
|
|
|
#define CONFIG_SOURCE
|
|
#define CONFIG_LOADS_ECHO 0 /* echo off for serial download */
|
|
#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
|
|
|
|
#undef CONFIG_WATCHDOG /* watchdog disabled */
|
|
|
|
#define CONFIG_STATUS_LED 1 /* Status LED enabled */
|
|
#define CONFIG_BOARD_SPECIFIC_LED /* version has board specific leds */
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_SUBNETMASK
|
|
#define CONFIG_BOOTP_GATEWAY
|
|
#define CONFIG_BOOTP_HOSTNAME
|
|
#define CONFIG_BOOTP_BOOTPATH
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
#define CONFIG_BOOTP_NISDOMAIN
|
|
|
|
|
|
#undef CONFIG_MAC_PARTITION
|
|
#undef CONFIG_DOS_PARTITION
|
|
|
|
#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
|
|
|
|
#define FEC_ENET 1 /* eth.c needs it that way... */
|
|
#undef CONFIG_SYS_DISCOVER_PHY
|
|
#define CONFIG_MII 1
|
|
#define CONFIG_MII_INIT 1
|
|
#undef CONFIG_RMII
|
|
|
|
#define CONFIG_ETHER_ON_FEC1 1
|
|
#define CONFIG_FEC1_PHY 1 /* phy address of FEC */
|
|
#undef CONFIG_FEC1_PHY_NORXERR
|
|
|
|
#define CONFIG_ETHER_ON_FEC2 1
|
|
#define CONFIG_FEC2_PHY 3
|
|
#undef CONFIG_FEC2_PHY_NORXERR
|
|
|
|
#define CONFIG_ENV_OVERWRITE 1 /* allow modification of vendor params */
|
|
|
|
|
|
/*
|
|
* Command line configuration.
|
|
*/
|
|
#include <config_cmd_default.h>
|
|
|
|
#define CONFIG_CMD_DHCP
|
|
#define CONFIG_CMD_MII
|
|
#define CONFIG_CMD_NFS
|
|
#define CONFIG_CMD_PING
|
|
|
|
|
|
#define CONFIG_BOARD_EARLY_INIT_F 1
|
|
#define CONFIG_MISC_INIT_R
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
|
#define CONFIG_SYS_PROMPT "xtc> " /* Monitor Command Prompt */
|
|
|
|
#define CONFIG_SYS_HUSH_PARSER 1
|
|
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
#else
|
|
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
|
|
#endif
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
|
|
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
|
|
|
|
#define CONFIG_SYS_MEMTEST_START 0x0300000 /* memtest works on */
|
|
#define CONFIG_SYS_MEMTEST_END 0x0700000 /* 3 ... 7 MB in DRAM */
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
|
|
|
|
/*
|
|
* Low Level Configuration Settings
|
|
* (address mappings, register initial values, etc.)
|
|
* You should know what you are doing if you make changes here.
|
|
*/
|
|
/*-----------------------------------------------------------------------
|
|
* Internal Memory Mapped Register
|
|
*/
|
|
#define CONFIG_SYS_IMMR 0xFF000000
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Definitions for initial stack pointer and data area (in DPRAM)
|
|
*/
|
|
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
|
|
#define CONFIG_SYS_INIT_RAM_SIZE 0x3000 /* Size of used area in DPRAM */
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Start addresses for the final memory configuration
|
|
* (Set up by the startup code)
|
|
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
|
|
*/
|
|
#define CONFIG_SYS_SDRAM_BASE 0x00000000
|
|
#define CONFIG_SYS_FLASH_BASE 0x40000000
|
|
#if defined(DEBUG)
|
|
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
|
|
#else
|
|
#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
|
|
#endif
|
|
|
|
/* yes this is weird, I know :) */
|
|
#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE | 0x00F00000)
|
|
#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
|
|
|
|
#define CONFIG_SYS_RESET_ADDRESS 0x80000000
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 8 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* FLASH organization
|
|
*/
|
|
#define CONFIG_ENV_IS_IN_FLASH 1
|
|
#define CONFIG_ENV_SECT_SIZE 0x10000
|
|
|
|
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00000000)
|
|
#define CONFIG_ENV_OFFSET 0
|
|
#define CONFIG_ENV_SIZE 0x4000
|
|
|
|
#define CONFIG_ENV_ADDR_REDUND (CONFIG_SYS_FLASH_BASE + 0x00010000)
|
|
#define CONFIG_ENV_OFFSET_REDUND 0
|
|
#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
|
|
|
|
#define CONFIG_SYS_FLASH_CFI 1
|
|
#define CONFIG_FLASH_CFI_DRIVER 1
|
|
#undef CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* use buffered writes (20x faster) */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
|
|
|
|
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE + 0x2000000 }
|
|
|
|
#define CONFIG_SYS_FLASH_PROTECTION
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Cache Configuration
|
|
*/
|
|
#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SYPCR - System Protection Control 11-9
|
|
* SYPCR can only be written once after reset!
|
|
*-----------------------------------------------------------------------
|
|
* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
|
|
*/
|
|
#if defined(CONFIG_WATCHDOG)
|
|
#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
|
|
SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
|
|
#else
|
|
#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SIUMCR - SIU Module Configuration 11-6
|
|
*-----------------------------------------------------------------------
|
|
* PCMCIA config., multi-function pin tri-state
|
|
*/
|
|
#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01 | SIUMCR_FRC | SIUMCR_GB5E)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* TBSCR - Time Base Status and Control 11-26
|
|
*-----------------------------------------------------------------------
|
|
* Clear Reference Interrupt Status, Timebase freezing enabled
|
|
*/
|
|
#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* RTCSC - Real-Time Clock Status and Control Register 11-27
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PISCR - Periodic Interrupt Status and Control 11-31
|
|
*-----------------------------------------------------------------------
|
|
* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
|
|
*/
|
|
#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
|
|
*-----------------------------------------------------------------------
|
|
* Reset PLL lock status sticky bit, timer expired status bit and timer
|
|
* interrupt status bit
|
|
*
|
|
*/
|
|
|
|
#if CONFIG_XIN == 10000000
|
|
|
|
#if MPC8XX_HZ == 50000000
|
|
#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
|
|
(1 << PLPRCR_S_SHIFT) | (10 << PLPRCR_MFI_SHIFT) | (0 << PLPRCR_PDF_SHIFT) | \
|
|
PLPRCR_TEXPS)
|
|
#elif MPC8XX_HZ == 66666666
|
|
#define CONFIG_SYS_PLPRCR ((1 << PLPRCR_MFN_SHIFT) | (2 << PLPRCR_MFD_SHIFT) | \
|
|
(1 << PLPRCR_S_SHIFT) | (13 << PLPRCR_MFI_SHIFT) | (0 << PLPRCR_PDF_SHIFT) | \
|
|
PLPRCR_TEXPS)
|
|
#else
|
|
#error unsupported CPU freq for XIN = 10MHz
|
|
#endif
|
|
#else
|
|
#error unsupported freq for XIN (must be 10MHz)
|
|
#endif
|
|
|
|
|
|
/*
|
|
*-----------------------------------------------------------------------
|
|
* SCCR - System Clock and reset Control Register 15-27
|
|
*-----------------------------------------------------------------------
|
|
* Set clock output, timebase and RTC source and divider,
|
|
* power management and some other internal clocks
|
|
*
|
|
* Note: When TBS == 0 the timebase is independent of current cpu clock.
|
|
*/
|
|
|
|
#define SCCR_MASK SCCR_EBDF11
|
|
#if MPC8XX_HZ > 66666666
|
|
#define CONFIG_SYS_SCCR (/* SCCR_TBS | */ SCCR_CRQEN | \
|
|
SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
|
|
SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
|
|
SCCR_DFALCD00 | SCCR_EBDF01)
|
|
#else
|
|
#define CONFIG_SYS_SCCR (/* SCCR_TBS | */ SCCR_CRQEN | \
|
|
SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
|
|
SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
|
|
SCCR_DFALCD00)
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
*
|
|
*-----------------------------------------------------------------------
|
|
*
|
|
*/
|
|
/*#define CONFIG_SYS_DER 0x2002000F*/
|
|
#define CONFIG_SYS_DER 0
|
|
|
|
/*
|
|
* Init Memory Controller:
|
|
*
|
|
* BR0/1 and OR0/1 (FLASH)
|
|
*/
|
|
|
|
#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
|
|
#define FLASH_BASE1_PRELIM 0x42000000 /* FLASH bank #1 */
|
|
|
|
/* used to re-map FLASH both when starting from SRAM or FLASH:
|
|
* restrict access enough to keep SRAM working (if any)
|
|
* but not too much to meddle with FLASH accesses
|
|
*/
|
|
|
|
#define FLASH_BANK_MAX_SIZE 0x01000000 /* max size per chip */
|
|
|
|
#define CONFIG_SYS_REMAP_OR_AM 0x80000000
|
|
#define CONFIG_SYS_PRELIM_OR_AM (0xFFFFFFFFLU & ~(FLASH_BANK_MAX_SIZE - 1))
|
|
|
|
/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1 */
|
|
#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_BI | OR_SCY_5_CLK | OR_TRLX)
|
|
|
|
#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
|
|
#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
|
|
#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V )
|
|
|
|
#define CONFIG_SYS_OR1_PRELIM ((0xFFFFFFFFLU & ~(FLASH_BANK_MAX_SIZE - 1)) | CONFIG_SYS_OR_TIMING_FLASH)
|
|
#define CONFIG_SYS_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V )
|
|
|
|
/*
|
|
* BR4 and OR4 (SDRAM)
|
|
*
|
|
*/
|
|
#define SDRAM_BASE1_PRELIM 0x00000000 /* SDRAM bank #0 */
|
|
#define SDRAM_MAX_SIZE (256 << 20) /* max 256MB per bank */
|
|
|
|
/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
|
|
#define CONFIG_SYS_OR_TIMING_SDRAM (OR_CSNT_SAM | OR_G5LS)
|
|
|
|
#define CONFIG_SYS_OR4_PRELIM ((0xFFFFFFFFLU & ~(SDRAM_MAX_SIZE - 1)) | CONFIG_SYS_OR_TIMING_SDRAM)
|
|
#define CONFIG_SYS_BR4_PRELIM ((SDRAM_BASE1_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_PS_32 | BR_V)
|
|
|
|
/*
|
|
* Memory Periodic Timer Prescaler
|
|
*/
|
|
|
|
/*
|
|
* Memory Periodic Timer Prescaler
|
|
*
|
|
* The Divider for PTA (refresh timer) configuration is based on an
|
|
* example SDRAM configuration (64 MBit, one bank). The adjustment to
|
|
* the number of chip selects (NCS) and the actually needed refresh
|
|
* rate is done by setting MPTPR.
|
|
*
|
|
* PTA is calculated from
|
|
* PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
|
|
*
|
|
* gclk CPU clock (not bus clock!)
|
|
* Trefresh Refresh cycle * 4 (four word bursts used)
|
|
*
|
|
* 4096 Rows from SDRAM example configuration
|
|
* 1000 factor s -> ms
|
|
* 32 PTP (pre-divider from MPTPR) from SDRAM example configuration
|
|
* 4 Number of refresh cycles per period
|
|
* 64 Refresh cycle in ms per number of rows
|
|
* --------------------------------------------
|
|
* Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
|
|
*
|
|
* 50 MHz => 50.000.000 / Divider = 98
|
|
* 66 Mhz => 66.000.000 / Divider = 129
|
|
* 80 Mhz => 80.000.000 / Divider = 156
|
|
*/
|
|
|
|
#define CONFIG_SYS_MAMR_PTA 234
|
|
|
|
/*
|
|
* For 16 MBit, refresh rates could be 31.3 us
|
|
* (= 64 ms / 2K = 125 / quad bursts).
|
|
* For a simpler initialization, 15.6 us is used instead.
|
|
*
|
|
* #define CONFIG_SYS_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks
|
|
* #define CONFIG_SYS_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank
|
|
*/
|
|
#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
|
|
#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
|
|
|
|
/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
|
|
#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
|
|
#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
|
|
|
|
/*
|
|
* MAMR settings for SDRAM
|
|
*/
|
|
|
|
/* 8 column SDRAM */
|
|
#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
|
|
MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
|
|
MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
|
|
|
|
/* 9 column SDRAM */
|
|
#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
|
|
MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
|
|
MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
|
|
|
|
#define CONFIG_LAST_STAGE_INIT /* needed to reset the damn phys */
|
|
|
|
/****************************************************************/
|
|
|
|
#define NAND_SIZE 0x00010000 /* 64K */
|
|
#define NAND_BASE 0xF1000000
|
|
|
|
/*****************************************************************************/
|
|
|
|
#define CONFIG_SYS_DIRECT_FLASH_TFTP
|
|
|
|
/*****************************************************************************/
|
|
|
|
/* Status Leds are on the MODCK pins, which become the PCMCIA PGCRB,
|
|
* CxOE and CxRESET. We use the CxOE.
|
|
*/
|
|
#define STATUS_LED_BIT 0x00000080 /* bit 24 */
|
|
|
|
#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
|
|
#define STATUS_LED_STATE STATUS_LED_BLINKING
|
|
|
|
#define STATUS_LED_ACTIVE 0 /* LED on for bit == 0 */
|
|
#define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
|
|
|
|
#ifndef __ASSEMBLY__
|
|
|
|
/* LEDs */
|
|
|
|
/* led_id_t is unsigned int mask */
|
|
typedef unsigned int led_id_t;
|
|
|
|
#define __led_toggle(_msk) \
|
|
do { \
|
|
((volatile immap_t *)CONFIG_SYS_IMMR)->im_pcmcia.pcmc_pgcrb ^= (_msk); \
|
|
} while(0)
|
|
|
|
#define __led_set(_msk, _st) \
|
|
do { \
|
|
if ((_st)) \
|
|
((volatile immap_t *)CONFIG_SYS_IMMR)->im_pcmcia.pcmc_pgcrb |= (_msk); \
|
|
else \
|
|
((volatile immap_t *)CONFIG_SYS_IMMR)->im_pcmcia.pcmc_pgcrb &= ~(_msk); \
|
|
} while(0)
|
|
|
|
#define __led_init(msk, st) __led_set(msk, st)
|
|
|
|
#endif
|
|
|
|
/******************************************************************************/
|
|
|
|
#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1
|
|
#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE 1
|
|
#define CONFIG_SYS_CONSOLE_ENV_OVERWRITE 1
|
|
|
|
/******************************************************************************/
|
|
|
|
/* use board specific hardware */
|
|
#undef CONFIG_WATCHDOG /* watchdog disabled */
|
|
#define CONFIG_HW_WATCHDOG
|
|
|
|
/*****************************************************************************/
|
|
|
|
#define CONFIG_AUTO_COMPLETE 1
|
|
#define CONFIG_CRC32_VERIFY 1
|
|
#define CONFIG_HUSH_OLD_PARSER_COMPATIBLE 1
|
|
|
|
/*****************************************************************************/
|
|
|
|
/* pass open firmware flattened device tree */
|
|
#define CONFIG_OF_LIBFDT 1
|
|
|
|
#define OF_TBCLK (MPC8XX_HZ / 16)
|
|
|
|
#endif /* __CONFIG_H */
|