mirror of
https://github.com/u-boot/u-boot.git
synced 2024-12-05 18:43:27 +08:00
344df3ca2c
A single DM-based driver should be able to support some feature for several PMIC variants where the interface is the same. For example, all PMIC variants use the same register bit to trigger poweroff. However, currently only definitions for a single PMIC are available at a time. This requires drivers to use #ifdefs and different indentifiers for each variant they support. Let's simplify this by making register definitions for all variants available from the header. Then no preprocessor conditions are needed; the driver can use the register definition from any variant that supports the relevant feature. An exception is the GPIO-related definitions, which do not use unique identifiers. So for now, keep them like before. They will be cleaned up along with the GPIO driver. Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
76 lines
2.5 KiB
C
76 lines
2.5 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* (C) Copyright 2015 Vishnu Patekar <vishnupatekar0510@gmail.com>
|
|
*
|
|
* X-Powers AXP818 Power Management IC driver
|
|
*/
|
|
|
|
#define AXP818_CHIP_ID 0x03
|
|
|
|
#define AXP818_OUTPUT_CTRL1 0x10
|
|
#define AXP818_OUTPUT_CTRL1_DCDC1_EN (1 << 0)
|
|
#define AXP818_OUTPUT_CTRL1_DCDC2_EN (1 << 1)
|
|
#define AXP818_OUTPUT_CTRL1_DCDC3_EN (1 << 2)
|
|
#define AXP818_OUTPUT_CTRL1_DCDC4_EN (1 << 3)
|
|
#define AXP818_OUTPUT_CTRL1_DCDC5_EN (1 << 4)
|
|
#define AXP818_OUTPUT_CTRL1_DCDC6_EN (1 << 5)
|
|
#define AXP818_OUTPUT_CTRL1_DCDC7_EN (1 << 6)
|
|
#define AXP818_OUTPUT_CTRL2 0x12
|
|
#define AXP818_OUTPUT_CTRL2_ELDO1_EN (1 << 0)
|
|
#define AXP818_OUTPUT_CTRL2_ELDO2_EN (1 << 1)
|
|
#define AXP818_OUTPUT_CTRL2_ELDO3_EN (1 << 2)
|
|
#define AXP818_OUTPUT_CTRL2_DLDO1_EN (1 << 3)
|
|
#define AXP818_OUTPUT_CTRL2_DLDO2_EN (1 << 4)
|
|
#define AXP818_OUTPUT_CTRL2_DLDO3_EN (1 << 5)
|
|
#define AXP818_OUTPUT_CTRL2_DLDO4_EN (1 << 6)
|
|
#define AXP818_OUTPUT_CTRL2_SW_EN (1 << 7)
|
|
#define AXP818_OUTPUT_CTRL3 0x13
|
|
#define AXP818_OUTPUT_CTRL3_FLDO1_EN (1 << 2)
|
|
#define AXP818_OUTPUT_CTRL3_FLDO2_EN (1 << 3)
|
|
#define AXP818_OUTPUT_CTRL3_FLDO3_EN (1 << 4)
|
|
#define AXP818_OUTPUT_CTRL3_ALDO1_EN (1 << 5)
|
|
#define AXP818_OUTPUT_CTRL3_ALDO2_EN (1 << 6)
|
|
#define AXP818_OUTPUT_CTRL3_ALDO3_EN (1 << 7)
|
|
|
|
#define AXP818_DLDO1_CTRL 0x15
|
|
#define AXP818_DLDO2_CTRL 0x16
|
|
#define AXP818_DLDO3_CTRL 0x17
|
|
#define AXP818_DLDO4_CTRL 0x18
|
|
#define AXP818_ELDO1_CTRL 0x19
|
|
#define AXP818_ELDO2_CTRL 0x1a
|
|
#define AXP818_ELDO3_CTRL 0x1b
|
|
#define AXP818_FLDO1_CTRL 0x1c
|
|
#define AXP818_FLDO2_3_CTRL 0x1d
|
|
#define AXP818_FLDO2_3_CTRL_FLDO3_VOL (1 << 4)
|
|
#define AXP818_DCDC1_CTRL 0x20
|
|
#define AXP818_DCDC2_CTRL 0x21
|
|
#define AXP818_DCDC3_CTRL 0x22
|
|
#define AXP818_DCDC4_CTRL 0x23
|
|
#define AXP818_DCDC5_CTRL 0x24
|
|
#define AXP818_DCDC6_CTRL 0x25
|
|
#define AXP818_DCDC7_CTRL 0x26
|
|
|
|
#define AXP818_ALDO1_CTRL 0x28
|
|
#define AXP818_ALDO2_CTRL 0x29
|
|
#define AXP818_ALDO3_CTRL 0x2a
|
|
|
|
#define AXP818_SHUTDOWN 0x32
|
|
#define AXP818_SHUTDOWN_POWEROFF (1 << 7)
|
|
|
|
/* For axp_gpio.c */
|
|
#ifdef CONFIG_AXP818_POWER
|
|
#define AXP_POWER_STATUS 0x00
|
|
#define AXP_POWER_STATUS_VBUS_PRESENT (1 << 5)
|
|
#define AXP_VBUS_IPSOUT 0x30
|
|
#define AXP_VBUS_IPSOUT_DRIVEBUS (1 << 2)
|
|
#define AXP_MISC_CTRL 0x8f
|
|
#define AXP_MISC_CTRL_N_VBUSEN_FUNC (1 << 4)
|
|
#define AXP_GPIO0_CTRL 0x90
|
|
#define AXP_GPIO1_CTRL 0x92
|
|
#define AXP_GPIO_CTRL_OUTPUT_LOW 0x00 /* Drive pin low */
|
|
#define AXP_GPIO_CTRL_OUTPUT_HIGH 0x01 /* Drive pin high */
|
|
#define AXP_GPIO_CTRL_INPUT 0x02 /* Input */
|
|
#define AXP_GPIO_STATE 0x94
|
|
#define AXP_GPIO_STATE_OFFSET 0
|
|
#endif
|