mirror of
https://github.com/u-boot/u-boot.git
synced 2024-11-26 13:44:29 +08:00
ef0f2f5752
This sets the default commands Kconfig to match include/config_cmd_default.h commands in the common/Kconfig and removes them from include/configs. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> [trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates] Signed-off-by: Tom Rini <trini@konsulko.com>
314 lines
9.7 KiB
C
314 lines
9.7 KiB
C
/*
|
|
* Copyright (C) 2003 ETC s.r.o.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
* Written by Peter Figuli <peposh@etc.sk>, 2003.
|
|
*
|
|
* 2003/13/06 Initial MP10 Support copied from wepep250
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
#define CONFIG_IMX 1 /* This is a Motorola MC9328MXL Chip */
|
|
#define CONFIG_SCB9328 1 /* on a scb9328tronix board */
|
|
|
|
#define CONFIG_IMX_SERIAL
|
|
#define CONFIG_IMX_SERIAL1
|
|
/*
|
|
* Select serial console configuration
|
|
*/
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
#define CONFIG_BOOTP_BOOTPATH
|
|
#define CONFIG_BOOTP_GATEWAY
|
|
#define CONFIG_BOOTP_HOSTNAME
|
|
|
|
/*
|
|
* Command line configuration.
|
|
*/
|
|
#define CONFIG_CMD_PING
|
|
#define CONFIG_CMD_DHCP
|
|
|
|
/*
|
|
* Boot options. Setting delay to -1 stops autostart count down.
|
|
* NOTE: Sending parameters to kernel depends on kernel version and
|
|
* 2.4.19-rmk6-pxa1 patch used while my u-boot coding didn't accept
|
|
* parameters at all! Do not get confused by them so.
|
|
*/
|
|
#define CONFIG_BOOTDELAY -1
|
|
#define CONFIG_BOOTARGS "console=ttySMX0,115200n8 root=/dev/mtdblock3 rootfstype=jffs2 mtdparts=scb9328_flash:128k(U-boot)ro,128k(U-boot_env),1m(kernel),4m(root),4m(fs) eval_board=evk9328"
|
|
#define CONFIG_BOOTCOMMAND "bootm 10040000"
|
|
#define CONFIG_SHOW_BOOT_PROGRESS
|
|
#define CONFIG_NETMASK 255.255.255.0
|
|
#define CONFIG_IPADDR 10.10.10.9
|
|
#define CONFIG_SERVERIP 10.10.10.10
|
|
|
|
/*
|
|
* General options for u-boot. Modify to save memory foot print
|
|
*/
|
|
#define CONFIG_SYS_LONGHELP /* undef saves memory */
|
|
#define CONFIG_SYS_PROMPT "scb9328> " /* prompt string */
|
|
#define CONFIG_SYS_CBSIZE 256 /* console I/O buffer */
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* print buffer size */
|
|
#define CONFIG_SYS_MAXARGS 16 /* max command args */
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* boot args buf size */
|
|
|
|
#define CONFIG_SYS_MEMTEST_START 0x08100000 /* memtest test area */
|
|
#define CONFIG_SYS_MEMTEST_END 0x08F00000
|
|
|
|
#define CONFIG_SYS_CPUSPEED 0x141 /* core clock - register value */
|
|
|
|
#define CONFIG_BAUDRATE 115200
|
|
/*
|
|
* Definitions related to passing arguments to kernel.
|
|
*/
|
|
#define CONFIG_CMDLINE_TAG 1 /* send commandline to Kernel */
|
|
#define CONFIG_SETUP_MEMORY_TAGS 1 /* send memory definition to kernel */
|
|
#define CONFIG_INITRD_TAG 1 /* send initrd params */
|
|
|
|
/*
|
|
* Malloc pool need to host env + 128 Kb reserve for other allocations.
|
|
*/
|
|
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128<<10) )
|
|
|
|
/* SDRAM Setup Values
|
|
0x910a8300 Precharge Command CAS 3
|
|
0x910a8200 Precharge Command CAS 2
|
|
|
|
0xa10a8300 AutoRefresh Command CAS 3
|
|
0xa10a8200 Set AutoRefresh Command CAS 2 */
|
|
|
|
#define PRECHARGE_CMD 0x910a8200
|
|
#define AUTOREFRESH_CMD 0xa10a8200
|
|
|
|
/*
|
|
* SDRAM Memory Map
|
|
*/
|
|
/* SH FIXME */
|
|
#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of SDRAM */
|
|
#define SCB9328_SDRAM_1 0x08000000 /* SDRAM bank #1 */
|
|
#define SCB9328_SDRAM_1_SIZE 0x01000000 /* 16 MB */
|
|
|
|
#define CONFIG_SYS_TEXT_BASE 0x10000000
|
|
|
|
#define CONFIG_SYS_SDRAM_BASE SCB9328_SDRAM_1
|
|
#define CONFIG_SYS_INIT_SP_ADDR (SCB9328_SDRAM_1 + 0xf00000)
|
|
|
|
/*
|
|
* Configuration for FLASH memory for the Synertronixx board
|
|
*/
|
|
|
|
/* #define SCB9328_FLASH_32M */
|
|
|
|
/* 32MB */
|
|
#ifdef SCB9328_FLASH_32M
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* FLASH banks count (not chip count)*/
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 256 /* number of sector in FLASH bank */
|
|
#define SCB9328_FLASH_BUS_WIDTH 2 /* we use 16 bit FLASH memory... */
|
|
#define SCB9328_FLASH_INTERLEAVE 1 /* ... made of 1 chip */
|
|
#define SCB9328_FLASH_BANK_SIZE 0x02000000 /* size of one flash bank */
|
|
#define SCB9328_FLASH_SECT_SIZE 0x00020000 /* size of erase sector */
|
|
#define SCB9328_FLASH_BASE 0x10000000 /* location of flash memory */
|
|
#define SCB9328_FLASH_UNLOCK 1 /* perform hw unlock first */
|
|
#else
|
|
|
|
/* 16MB */
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* FLASH banks count (not chip count)*/
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 128 /* number of sector in FLASH bank */
|
|
#define SCB9328_FLASH_BUS_WIDTH 2 /* we use 16 bit FLASH memory... */
|
|
#define SCB9328_FLASH_INTERLEAVE 1 /* ... made of 1 chip */
|
|
#define SCB9328_FLASH_BANK_SIZE 0x01000000 /* size of one flash bank */
|
|
#define SCB9328_FLASH_SECT_SIZE 0x00020000 /* size of erase sector */
|
|
#define SCB9328_FLASH_BASE 0x10000000 /* location of flash memory */
|
|
#define SCB9328_FLASH_UNLOCK 1 /* perform hw unlock first */
|
|
#endif /* SCB9328_FLASH_32M */
|
|
|
|
/* This should be defined if CFI FLASH device is present. Actually benefit
|
|
is not so clear to me. In other words we can provide more informations
|
|
to user, but this expects more complex flash handling we do not provide
|
|
now.*/
|
|
#undef CONFIG_SYS_FLASH_CFI
|
|
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* timeout for Erase operation */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 240000 /* timeout for Write operation */
|
|
|
|
#define CONFIG_SYS_FLASH_BASE SCB9328_FLASH_BASE
|
|
|
|
/*
|
|
* This is setting for JFFS2 support in u-boot.
|
|
* Right now there is no gain for user, but later on booting kernel might be
|
|
* possible. Consider using XIP kernel running from flash to save RAM
|
|
* footprint.
|
|
* NOTE: Enable CONFIG_CMD_JFFS2 for JFFS2 support.
|
|
*/
|
|
#define CONFIG_SYS_JFFS2_FIRST_BANK 0
|
|
#define CONFIG_SYS_JFFS2_FIRST_SECTOR 5
|
|
#define CONFIG_SYS_JFFS2_NUM_BANKS 1
|
|
|
|
/*
|
|
* Environment setup. Definitions of monitor location and size with
|
|
* definition of environment setup ends up in 2 possibilities.
|
|
* 1. Embeded environment - in u-boot code is space for environment
|
|
* 2. Environment is read from predefined sector of flash
|
|
* Right now we support 2. possiblity, but expecting no env placed
|
|
* on mentioned address right now. This also needs to provide whole
|
|
* sector for it - for us 256Kb is really waste of memory. U-boot uses
|
|
* default env. and until kernel parameters could be sent to kernel
|
|
* env. has no sense to us.
|
|
*/
|
|
|
|
/* Setup for PA23 which is Reset Default PA23 but has to become
|
|
CS5 */
|
|
|
|
#define CONFIG_SYS_GPR_A_VAL 0x00800000
|
|
#define CONFIG_SYS_GIUS_A_VAL 0x0043fffe
|
|
|
|
#define CONFIG_SYS_MONITOR_BASE 0x10000000
|
|
#define CONFIG_SYS_MONITOR_LEN 0x20000 /* 128b ( 1 flash sector ) */
|
|
#define CONFIG_ENV_IS_IN_FLASH 1
|
|
#define CONFIG_ENV_ADDR 0x10020000 /* absolute address for now */
|
|
#define CONFIG_ENV_SIZE 0x20000
|
|
|
|
#define CONFIG_ENV_OVERWRITE 1 /* env is not writable now */
|
|
|
|
/*
|
|
* CSxU_VAL:
|
|
* 63| x x x x | x x x x | x x x x | x x x x | x x x x | x x x x | x x x x | x x x x|32
|
|
* |DTACK_SEL|0|BCD | BCS | PSZ|PME|SYNC| DOL | CNC| WSC | 0| WWS | EDC |
|
|
*
|
|
* CSxL_VAL:
|
|
* 31| x x x x | x x x x | x x x x | x x x x | x x x x | x x x x | x x x x | x x x x| 0
|
|
* | OEA | OEN | WEA | WEN | CSA |EBC| DSZ | 0|SP|0|WP| 0 0|PA|CSEN|
|
|
*/
|
|
|
|
#define CONFIG_SYS_CS0U_VAL 0x000F2000
|
|
#define CONFIG_SYS_CS0L_VAL 0x11110d01
|
|
#define CONFIG_SYS_CS1U_VAL 0x000F0a00
|
|
#define CONFIG_SYS_CS1L_VAL 0x11110601
|
|
#define CONFIG_SYS_CS2U_VAL 0x0
|
|
#define CONFIG_SYS_CS2L_VAL 0x0
|
|
|
|
#define CONFIG_SYS_CS3U_VAL 0x000FFFFF
|
|
#define CONFIG_SYS_CS3L_VAL 0x00000303
|
|
|
|
#define CONFIG_SYS_CS4U_VAL 0x000F0a00
|
|
#define CONFIG_SYS_CS4L_VAL 0x11110301
|
|
|
|
/* CNC == 3 too long
|
|
#define CONFIG_SYS_CS5U_VAL 0x0000C210 */
|
|
|
|
/* #define CONFIG_SYS_CS5U_VAL 0x00008400
|
|
mal laenger mahcen, ob der bei 150MHz laenger haelt dann und
|
|
kaum langsamer ist */
|
|
/* #define CONFIG_SYS_CS5U_VAL 0x00009400
|
|
#define CONFIG_SYS_CS5L_VAL 0x11010D03 */
|
|
|
|
#define CONFIG_SYS_CS5U_VAL 0x00008400
|
|
#define CONFIG_SYS_CS5L_VAL 0x00000D03
|
|
|
|
#define CONFIG_DRIVER_DM9000 1
|
|
#define CONFIG_DM9000_BASE 0x16000000
|
|
#define DM9000_IO CONFIG_DM9000_BASE
|
|
#define DM9000_DATA (CONFIG_DM9000_BASE+4)
|
|
|
|
/* f_{dpll}=2*f{ref}*(MFI+MFN/(MFD+1))/(PD+1)
|
|
f_ref=16,777MHz
|
|
|
|
0x002a141f: 191,9944MHz
|
|
0x040b2007: 144MHz
|
|
0x042a141f: 96MHz
|
|
0x0811140d: 64MHz
|
|
0x040e200e: 150MHz
|
|
0x00321431: 200MHz
|
|
|
|
0x08001800: 64MHz mit 16er Quarz
|
|
0x04001800: 96MHz mit 16er Quarz
|
|
0x04002400: 144MHz mit 16er Quarz
|
|
|
|
31 |x x x x|x x x x|x x x x|x x x x|x x x x|x x x x|x x x x|x x x x| 0
|
|
|XXX|--PD---|-------MFD---------|XXX|--MFI--|-----MFN-----------| */
|
|
|
|
#define CPU200
|
|
|
|
#ifdef CPU200
|
|
#define CONFIG_SYS_MPCTL0_VAL 0x00321431
|
|
#else
|
|
#define CONFIG_SYS_MPCTL0_VAL 0x040e200e
|
|
#endif
|
|
|
|
/* #define BUS64 */
|
|
#define BUS72
|
|
|
|
#ifdef BUS72
|
|
#define CONFIG_SYS_SPCTL0_VAL 0x04002400
|
|
#endif
|
|
|
|
#ifdef BUS96
|
|
#define CONFIG_SYS_SPCTL0_VAL 0x04001800
|
|
#endif
|
|
|
|
#ifdef BUS64
|
|
#define CONFIG_SYS_SPCTL0_VAL 0x08001800
|
|
#endif
|
|
|
|
/* Das ist der BCLK Divider, der aus der System PLL
|
|
BCLK und HCLK erzeugt:
|
|
31 | xxxx xxxx xxxx xxxx xx10 11xx xxxx xxxx | 0
|
|
0x2f008403 : 192MHz/2=96MHz, 144MHz/2=72MHz PRESC=1->BCLKDIV=2
|
|
0x2f008803 : 192MHz/3=64MHz, 240MHz/3=80MHz PRESC=1->BCLKDIV=2
|
|
0x2f001003 : 192MHz/5=38,4MHz
|
|
0x2f000003 : 64MHz/1
|
|
Bit 22: SPLL Restart
|
|
Bit 21: MPLL Restart */
|
|
|
|
#ifdef BUS64
|
|
#define CONFIG_SYS_CSCR_VAL 0x2f030003
|
|
#endif
|
|
|
|
#ifdef BUS72
|
|
#define CONFIG_SYS_CSCR_VAL 0x2f030403
|
|
#endif
|
|
|
|
/*
|
|
* Well this has to be defined, but on the other hand it is used differently
|
|
* one may expect. For instance loadb command do not cares :-)
|
|
* So advice is - do not relay on this...
|
|
*/
|
|
#define CONFIG_SYS_LOAD_ADDR 0x08400000
|
|
|
|
#define MHZ16QUARZINUSE
|
|
|
|
#ifdef MHZ16QUARZINUSE
|
|
#define CONFIG_SYSPLL_CLK_FREQ 16000000
|
|
#else
|
|
#define CONFIG_SYSPLL_CLK_FREQ 16780000
|
|
#endif
|
|
|
|
#define CONFIG_SYS_CLK_FREQ 16780000
|
|
|
|
/* FMCR Bit 0 becomes 0 to make CS3 CS3 :P */
|
|
#define CONFIG_SYS_FMCR_VAL 0x00000001
|
|
|
|
/* Bit[0:3] contain PERCLK1DIV for UART 1
|
|
0x000b00b ->b<- -> 192MHz/12=16MHz
|
|
0x000b00b ->8<- -> 144MHz/09=16MHz
|
|
0x000b00b ->3<- -> 64MHz/4=16MHz */
|
|
|
|
#ifdef BUS96
|
|
#define CONFIG_SYS_PCDR_VAL 0x000b00b5
|
|
#endif
|
|
|
|
#ifdef BUS64
|
|
#define CONFIG_SYS_PCDR_VAL 0x000b00b3
|
|
#endif
|
|
|
|
#ifdef BUS72
|
|
#define CONFIG_SYS_PCDR_VAL 0x000b00b8
|
|
#endif
|
|
|
|
#endif /* __CONFIG_H */
|