0
0
mirror of https://github.com/u-boot/u-boot.git synced 2024-12-14 07:13:28 +08:00
u-boot/include/configs/tb100.h
Simon Glass 2be296538e Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to Kconfig
This converts the following to Kconfig:
   CONFIG_ENV_IS_IN_MMC
   CONFIG_ENV_IS_IN_NAND
   CONFIG_ENV_IS_IN_UBI
   CONFIG_ENV_IS_NOWHERE

In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.

In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.

There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with

   ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC

And then manual updates.  This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-07-25 21:08:01 -04:00

88 lines
1.9 KiB
C

/*
* Copyright (C) 2011-2014 Pierrick Hascoet, Abilis Systems
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef _CONFIG_TB100_H_
#define _CONFIG_TB100_H_
#include <linux/sizes.h>
/*
* Memory configuration
*/
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_SYS_SDRAM_SIZE SZ_128M
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_MALLOC_LEN SZ_128K
#define CONFIG_SYS_BOOTM_LEN SZ_32M
#define CONFIG_SYS_LOAD_ADDR 0x82000000
/*
* UART configuration
*/
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_CLK 166666666
/*
* Ethernet PHY configuration
*/
#define CONFIG_PHY_GIGE
/*
* Even though the board houses Realtek RTL8211E PHY
* corresponding PHY driver (drivers/net/phy/realtek.c) behaves unexpectedly.
* In particular "parse_status" reports link is down.
*
* Until Realtek PHY driver is fixed fall back to generic PHY driver
* which implements all required functionality and behaves much more stable.
*
* #define CONFIG_PHY_REALTEK
*
*/
/*
* Ethernet configuration
*/
#define ETH0_BASE_ADDRESS 0xFE100000
#define ETH1_BASE_ADDRESS 0xFE110000
/*
* Command line configuration
*/
#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_MAXARGS 16
#define CONFIG_CMDLINE_EDITING
/*
* Environment settings
*/
#define CONFIG_ENV_SIZE SZ_2K
#define CONFIG_ENV_OFFSET 0
/*
* Environment configuration
*/
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_BOOTARGS "console=ttyS0,115200n8"
#define CONFIG_LOADADDR CONFIG_SYS_LOAD_ADDR
/*
* Console configuration
*/
#define CONFIG_SYS_LONGHELP
#define CONFIG_SYS_CBSIZE 256
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
#endif /* _CONFIG_TB100_H_ */