u-boot/drivers/mmc/mvebu_mmc.c
Rob Herring 5a20397b00 mmc: remove the MMC_MODE_HC flag
High capacity support is not a host capability, but a device capability
that is queried via the OCR. The flag in the operating conditions
request argument can just be set unconditionally. This matches the Linux
implementation.

[panto] Hand merged and renumbering MMC_MODE_DDR_52MHz.

Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
2015-05-05 12:29:36 +03:00

439 lines
11 KiB
C

/*
* Marvell MMC/SD/SDIO driver
*
* (C) Copyright 2012-2014
* Marvell Semiconductor <www.marvell.com>
* Written-by: Maen Suleiman, Gerald Kerma
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <malloc.h>
#include <part.h>
#include <mmc.h>
#include <asm/io.h>
#include <asm/arch/cpu.h>
#include <asm/arch/soc.h>
#include <mvebu_mmc.h>
DECLARE_GLOBAL_DATA_PTR;
#define DRIVER_NAME "MVEBU_MMC"
#define MVEBU_TARGET_DRAM 0
#define TIMEOUT_DELAY 5*CONFIG_SYS_HZ /* wait 5 seconds */
static void mvebu_mmc_write(u32 offs, u32 val)
{
writel(val, CONFIG_SYS_MMC_BASE + (offs));
}
static u32 mvebu_mmc_read(u32 offs)
{
return readl(CONFIG_SYS_MMC_BASE + (offs));
}
static int mvebu_mmc_setup_data(struct mmc_data *data)
{
u32 ctrl_reg;
debug("%s, data %s : blocks=%d blksz=%d\n", DRIVER_NAME,
(data->flags & MMC_DATA_READ) ? "read" : "write",
data->blocks, data->blocksize);
/* default to maximum timeout */
ctrl_reg = mvebu_mmc_read(SDIO_HOST_CTRL);
ctrl_reg |= SDIO_HOST_CTRL_TMOUT(SDIO_HOST_CTRL_TMOUT_MAX);
mvebu_mmc_write(SDIO_HOST_CTRL, ctrl_reg);
if (data->flags & MMC_DATA_READ) {
mvebu_mmc_write(SDIO_SYS_ADDR_LOW, (u32)data->dest & 0xffff);
mvebu_mmc_write(SDIO_SYS_ADDR_HI, (u32)data->dest >> 16);
} else {
mvebu_mmc_write(SDIO_SYS_ADDR_LOW, (u32)data->src & 0xffff);
mvebu_mmc_write(SDIO_SYS_ADDR_HI, (u32)data->src >> 16);
}
mvebu_mmc_write(SDIO_BLK_COUNT, data->blocks);
mvebu_mmc_write(SDIO_BLK_SIZE, data->blocksize);
return 0;
}
static int mvebu_mmc_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd,
struct mmc_data *data)
{
ulong start;
ushort waittype = 0;
ushort resptype = 0;
ushort xfertype = 0;
ushort resp_indx = 0;
debug("%s: cmdidx [0x%x] resp_type[0x%x] cmdarg[0x%x]\n",
DRIVER_NAME, cmd->cmdidx, cmd->resp_type, cmd->cmdarg);
debug("%s: cmd %d (hw state 0x%04x)\n", DRIVER_NAME,
cmd->cmdidx, mvebu_mmc_read(SDIO_HW_STATE));
/*
* Hardware weirdness. The FIFO_EMPTY bit of the HW_STATE
* register is sometimes not set before a while when some
* "unusual" data block sizes are used (such as with the SWITCH
* command), even despite the fact that the XFER_DONE interrupt
* was raised. And if another data transfer starts before
* this bit comes to good sense (which eventually happens by
* itself) then the new transfer simply fails with a timeout.
*/
if (!(mvebu_mmc_read(SDIO_HW_STATE) & CMD_FIFO_EMPTY)) {
ushort hw_state, count = 0;
start = get_timer(0);
do {
hw_state = mvebu_mmc_read(SDIO_HW_STATE);
if ((get_timer(0) - start) > TIMEOUT_DELAY) {
printf("%s : FIFO_EMPTY bit missing\n",
DRIVER_NAME);
break;
}
count++;
} while (!(hw_state & CMD_FIFO_EMPTY));
debug("%s *** wait for FIFO_EMPTY bit (hw=0x%04x, count=%d, jiffies=%ld)\n",
DRIVER_NAME, hw_state, count, (get_timer(0) - (start)));
}
/* Clear status */
mvebu_mmc_write(SDIO_NOR_INTR_STATUS, SDIO_POLL_MASK);
mvebu_mmc_write(SDIO_ERR_INTR_STATUS, SDIO_POLL_MASK);
resptype = SDIO_CMD_INDEX(cmd->cmdidx);
/* Analyzing resptype/xfertype/waittype for the command */
if (cmd->resp_type & MMC_RSP_BUSY)
resptype |= SDIO_CMD_RSP_48BUSY;
else if (cmd->resp_type & MMC_RSP_136)
resptype |= SDIO_CMD_RSP_136;
else if (cmd->resp_type & MMC_RSP_PRESENT)
resptype |= SDIO_CMD_RSP_48;
else
resptype |= SDIO_CMD_RSP_NONE;
if (cmd->resp_type & MMC_RSP_CRC)
resptype |= SDIO_CMD_CHECK_CMDCRC;
if (cmd->resp_type & MMC_RSP_OPCODE)
resptype |= SDIO_CMD_INDX_CHECK;
if (cmd->resp_type & MMC_RSP_PRESENT) {
resptype |= SDIO_UNEXPECTED_RESP;
waittype |= SDIO_NOR_UNEXP_RSP;
}
if (data) {
int err = mvebu_mmc_setup_data(data);
if (err) {
debug("%s: command DATA error :%x\n",
DRIVER_NAME, err);
return err;
}
resptype |= SDIO_CMD_DATA_PRESENT | SDIO_CMD_CHECK_DATACRC16;
xfertype |= SDIO_XFER_MODE_HW_WR_DATA_EN;
if (data->flags & MMC_DATA_READ) {
xfertype |= SDIO_XFER_MODE_TO_HOST;
waittype = SDIO_NOR_DMA_INI;
} else {
waittype |= SDIO_NOR_XFER_DONE;
}
} else {
waittype |= SDIO_NOR_CMD_DONE;
}
/* Setting cmd arguments */
mvebu_mmc_write(SDIO_ARG_LOW, cmd->cmdarg & 0xffff);
mvebu_mmc_write(SDIO_ARG_HI, cmd->cmdarg >> 16);
/* Setting Xfer mode */
mvebu_mmc_write(SDIO_XFER_MODE, xfertype);
/* Sending command */
mvebu_mmc_write(SDIO_CMD, resptype);
start = get_timer(0);
while (!((mvebu_mmc_read(SDIO_NOR_INTR_STATUS)) & waittype)) {
if (mvebu_mmc_read(SDIO_NOR_INTR_STATUS) & SDIO_NOR_ERROR) {
debug("%s: error! cmdidx : %d, err reg: %04x\n",
DRIVER_NAME, cmd->cmdidx,
mvebu_mmc_read(SDIO_ERR_INTR_STATUS));
if (mvebu_mmc_read(SDIO_ERR_INTR_STATUS) &
(SDIO_ERR_CMD_TIMEOUT | SDIO_ERR_DATA_TIMEOUT)) {
debug("%s: command READ timed out\n",
DRIVER_NAME);
return TIMEOUT;
}
debug("%s: command READ error\n", DRIVER_NAME);
return COMM_ERR;
}
if ((get_timer(0) - start) > TIMEOUT_DELAY) {
debug("%s: command timed out\n", DRIVER_NAME);
return TIMEOUT;
}
}
/* Handling response */
if (cmd->resp_type & MMC_RSP_136) {
uint response[8];
for (resp_indx = 0; resp_indx < 8; resp_indx++)
response[resp_indx]
= mvebu_mmc_read(SDIO_RSP(resp_indx));
cmd->response[0] = ((response[0] & 0x03ff) << 22) |
((response[1] & 0xffff) << 6) |
((response[2] & 0xfc00) >> 10);
cmd->response[1] = ((response[2] & 0x03ff) << 22) |
((response[3] & 0xffff) << 6) |
((response[4] & 0xfc00) >> 10);
cmd->response[2] = ((response[4] & 0x03ff) << 22) |
((response[5] & 0xffff) << 6) |
((response[6] & 0xfc00) >> 10);
cmd->response[3] = ((response[6] & 0x03ff) << 22) |
((response[7] & 0x3fff) << 8);
} else if (cmd->resp_type & MMC_RSP_PRESENT) {
uint response[3];
for (resp_indx = 0; resp_indx < 3; resp_indx++)
response[resp_indx]
= mvebu_mmc_read(SDIO_RSP(resp_indx));
cmd->response[0] = ((response[2] & 0x003f) << (8 - 8)) |
((response[1] & 0xffff) << (14 - 8)) |
((response[0] & 0x03ff) << (30 - 8));
cmd->response[1] = ((response[0] & 0xfc00) >> 10);
cmd->response[2] = 0;
cmd->response[3] = 0;
} else {
cmd->response[0] = 0;
cmd->response[1] = 0;
cmd->response[2] = 0;
cmd->response[3] = 0;
}
debug("%s: resp[0x%x] ", DRIVER_NAME, cmd->resp_type);
debug("[0x%x] ", cmd->response[0]);
debug("[0x%x] ", cmd->response[1]);
debug("[0x%x] ", cmd->response[2]);
debug("[0x%x] ", cmd->response[3]);
debug("\n");
if (mvebu_mmc_read(SDIO_ERR_INTR_STATUS) &
(SDIO_ERR_CMD_TIMEOUT | SDIO_ERR_DATA_TIMEOUT))
return TIMEOUT;
return 0;
}
static void mvebu_mmc_power_up(void)
{
debug("%s: power up\n", DRIVER_NAME);
/* disable interrupts */
mvebu_mmc_write(SDIO_NOR_INTR_EN, 0);
mvebu_mmc_write(SDIO_ERR_INTR_EN, 0);
/* SW reset */
mvebu_mmc_write(SDIO_SW_RESET, SDIO_SW_RESET_NOW);
mvebu_mmc_write(SDIO_XFER_MODE, 0);
/* enable status */
mvebu_mmc_write(SDIO_NOR_STATUS_EN, SDIO_POLL_MASK);
mvebu_mmc_write(SDIO_ERR_STATUS_EN, SDIO_POLL_MASK);
/* enable interrupts status */
mvebu_mmc_write(SDIO_NOR_INTR_STATUS, SDIO_POLL_MASK);
mvebu_mmc_write(SDIO_ERR_INTR_STATUS, SDIO_POLL_MASK);
}
static void mvebu_mmc_set_clk(unsigned int clock)
{
unsigned int m;
if (clock == 0) {
debug("%s: clock off\n", DRIVER_NAME);
mvebu_mmc_write(SDIO_XFER_MODE, SDIO_XFER_MODE_STOP_CLK);
mvebu_mmc_write(SDIO_CLK_DIV, MVEBU_MMC_BASE_DIV_MAX);
} else {
m = MVEBU_MMC_BASE_FAST_CLOCK/(2*clock) - 1;
if (m > MVEBU_MMC_BASE_DIV_MAX)
m = MVEBU_MMC_BASE_DIV_MAX;
mvebu_mmc_write(SDIO_CLK_DIV, m & MVEBU_MMC_BASE_DIV_MAX);
debug("%s: clock (%d) div : %d\n", DRIVER_NAME, clock, m);
}
}
static void mvebu_mmc_set_bus(unsigned int bus)
{
u32 ctrl_reg = 0;
ctrl_reg = mvebu_mmc_read(SDIO_HOST_CTRL);
ctrl_reg &= ~SDIO_HOST_CTRL_DATA_WIDTH_4_BITS;
switch (bus) {
case 4:
ctrl_reg |= SDIO_HOST_CTRL_DATA_WIDTH_4_BITS;
break;
case 1:
default:
ctrl_reg |= SDIO_HOST_CTRL_DATA_WIDTH_1_BIT;
}
/* default transfer mode */
ctrl_reg |= SDIO_HOST_CTRL_BIG_ENDIAN;
ctrl_reg &= ~SDIO_HOST_CTRL_LSB_FIRST;
/* default to maximum timeout */
ctrl_reg |= SDIO_HOST_CTRL_TMOUT(SDIO_HOST_CTRL_TMOUT_MAX);
ctrl_reg |= SDIO_HOST_CTRL_TMOUT_EN;
ctrl_reg |= SDIO_HOST_CTRL_PUSH_PULL_EN;
ctrl_reg |= SDIO_HOST_CTRL_CARD_TYPE_MEM_ONLY;
debug("%s: ctrl 0x%04x: %s %s %s\n", DRIVER_NAME, ctrl_reg,
(ctrl_reg & SDIO_HOST_CTRL_PUSH_PULL_EN) ?
"push-pull" : "open-drain",
(ctrl_reg & SDIO_HOST_CTRL_DATA_WIDTH_4_BITS) ?
"4bit-width" : "1bit-width",
(ctrl_reg & SDIO_HOST_CTRL_HI_SPEED_EN) ?
"high-speed" : "");
mvebu_mmc_write(SDIO_HOST_CTRL, ctrl_reg);
}
static void mvebu_mmc_set_ios(struct mmc *mmc)
{
debug("%s: bus[%d] clock[%d]\n", DRIVER_NAME,
mmc->bus_width, mmc->clock);
mvebu_mmc_set_bus(mmc->bus_width);
mvebu_mmc_set_clk(mmc->clock);
}
/*
* Set window register.
*/
static void mvebu_window_setup(void)
{
int i;
for (i = 0; i < 4; i++) {
mvebu_mmc_write(WINDOW_CTRL(i), 0);
mvebu_mmc_write(WINDOW_BASE(i), 0);
}
for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
u32 size, base, attrib;
/* Enable DRAM bank */
switch (i) {
case 0:
attrib = KWCPU_ATTR_DRAM_CS0;
break;
case 1:
attrib = KWCPU_ATTR_DRAM_CS1;
break;
case 2:
attrib = KWCPU_ATTR_DRAM_CS2;
break;
case 3:
attrib = KWCPU_ATTR_DRAM_CS3;
break;
default:
/* invalide bank, disable access */
attrib = 0;
break;
}
size = gd->bd->bi_dram[i].size;
base = gd->bd->bi_dram[i].start;
if (size && attrib) {
mvebu_mmc_write(WINDOW_CTRL(i),
MVCPU_WIN_CTRL_DATA(size,
MVEBU_TARGET_DRAM,
attrib,
MVCPU_WIN_ENABLE));
} else {
mvebu_mmc_write(WINDOW_CTRL(i), MVCPU_WIN_DISABLE);
}
mvebu_mmc_write(WINDOW_BASE(i), base);
}
}
static int mvebu_mmc_initialize(struct mmc *mmc)
{
debug("%s: mvebu_mmc_initialize\n", DRIVER_NAME);
/*
* Setting host parameters
* Initial Host Ctrl : Timeout : max , Normal Speed mode,
* 4-bit data mode, Big Endian, SD memory Card, Push_pull CMD Line
*/
mvebu_mmc_write(SDIO_HOST_CTRL,
SDIO_HOST_CTRL_TMOUT(SDIO_HOST_CTRL_TMOUT_MAX) |
SDIO_HOST_CTRL_DATA_WIDTH_4_BITS |
SDIO_HOST_CTRL_BIG_ENDIAN |
SDIO_HOST_CTRL_PUSH_PULL_EN |
SDIO_HOST_CTRL_CARD_TYPE_MEM_ONLY);
mvebu_mmc_write(SDIO_CLK_CTRL, 0);
/* enable status */
mvebu_mmc_write(SDIO_NOR_STATUS_EN, SDIO_POLL_MASK);
mvebu_mmc_write(SDIO_ERR_STATUS_EN, SDIO_POLL_MASK);
/* disable interrupts */
mvebu_mmc_write(SDIO_NOR_INTR_EN, 0);
mvebu_mmc_write(SDIO_ERR_INTR_EN, 0);
mvebu_window_setup();
/* SW reset */
mvebu_mmc_write(SDIO_SW_RESET, SDIO_SW_RESET_NOW);
return 0;
}
static const struct mmc_ops mvebu_mmc_ops = {
.send_cmd = mvebu_mmc_send_cmd,
.set_ios = mvebu_mmc_set_ios,
.init = mvebu_mmc_initialize,
};
static struct mmc_config mvebu_mmc_cfg = {
.name = DRIVER_NAME,
.ops = &mvebu_mmc_ops,
.f_min = MVEBU_MMC_BASE_FAST_CLOCK / MVEBU_MMC_BASE_DIV_MAX,
.f_max = MVEBU_MMC_CLOCKRATE_MAX,
.voltages = MMC_VDD_32_33 | MMC_VDD_33_34,
.host_caps = MMC_MODE_4BIT | MMC_MODE_HS |
MMC_MODE_HS_52MHz,
.part_type = PART_TYPE_DOS,
.b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT,
};
int mvebu_mmc_init(bd_t *bis)
{
struct mmc *mmc;
mvebu_mmc_power_up();
mmc = mmc_create(&mvebu_mmc_cfg, bis);
if (mmc == NULL)
return -1;
return 0;
}