mirror of
https://github.com/u-boot/u-boot.git
synced 2024-12-22 19:23:26 +08:00
1a4596601f
Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
121 lines
3.5 KiB
C
121 lines
3.5 KiB
C
/*
|
|
* Adaptive Body Bias programming sequence for OMAP family
|
|
*
|
|
* (C) Copyright 2013
|
|
* Texas Instruments, <www.ti.com>
|
|
*
|
|
* Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <asm/omap_common.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
|
|
__weak s8 abb_setup_ldovbb(u32 fuse, u32 ldovbb)
|
|
{
|
|
return -1;
|
|
}
|
|
|
|
static void abb_setup_timings(u32 setup)
|
|
{
|
|
u32 sys_rate, sr2_cnt, clk_cycles;
|
|
|
|
/*
|
|
* SR2_WTCNT_VALUE is the settling time for the ABB ldo after a
|
|
* transition and must be programmed with the correct time at boot.
|
|
* The value programmed into the register is the number of SYS_CLK
|
|
* clock cycles that match a given wall time profiled for the ldo.
|
|
* This value depends on:
|
|
* settling time of ldo in micro-seconds (varies per OMAP family),
|
|
* of clock cycles per SYS_CLK period (varies per OMAP family),
|
|
* the SYS_CLK frequency in MHz (varies per board)
|
|
* The formula is:
|
|
*
|
|
* ldo settling time (in micro-seconds)
|
|
* SR2_WTCNT_VALUE = ------------------------------------------
|
|
* (# system clock cycles) * (sys_clk period)
|
|
*
|
|
* Put another way:
|
|
*
|
|
* SR2_WTCNT_VALUE = settling time / (# SYS_CLK cycles / SYS_CLK rate))
|
|
*
|
|
* To avoid dividing by zero multiply both "# clock cycles" and
|
|
* "settling time" by 10 such that the final result is the one we want.
|
|
*/
|
|
|
|
/* calculate SR2_WTCNT_VALUE */
|
|
sys_rate = DIV_ROUND(V_OSCK, 1000000);
|
|
clk_cycles = DIV_ROUND(OMAP_ABB_CLOCK_CYCLES * 10, sys_rate);
|
|
sr2_cnt = DIV_ROUND(OMAP_ABB_SETTLING_TIME * 10, clk_cycles);
|
|
|
|
setbits_le32(setup,
|
|
sr2_cnt << (ffs(OMAP_ABB_SETUP_SR2_WTCNT_VALUE_MASK) - 1));
|
|
}
|
|
|
|
void abb_setup(u32 fuse, u32 ldovbb, u32 setup, u32 control,
|
|
u32 txdone, u32 txdone_mask, u32 opp)
|
|
{
|
|
u32 abb_type_mask, opp_sel_mask;
|
|
|
|
/* sanity check */
|
|
if (!setup || !control || !txdone)
|
|
return;
|
|
|
|
/* setup ABB only in case of Fast or Slow OPP */
|
|
switch (opp) {
|
|
case OMAP_ABB_FAST_OPP:
|
|
abb_type_mask = OMAP_ABB_SETUP_ACTIVE_FBB_SEL_MASK;
|
|
opp_sel_mask = OMAP_ABB_CONTROL_FAST_OPP_SEL_MASK;
|
|
break;
|
|
case OMAP_ABB_SLOW_OPP:
|
|
abb_type_mask = OMAP_ABB_SETUP_ACTIVE_RBB_SEL_MASK;
|
|
opp_sel_mask = OMAP_ABB_CONTROL_SLOW_OPP_SEL_MASK;
|
|
break;
|
|
default:
|
|
return;
|
|
}
|
|
|
|
/*
|
|
* For some OMAP silicons additional setup for LDOVBB register is
|
|
* required. This is determined by data retrieved from corresponding
|
|
* OPP EFUSE register. Data, which is retrieved from EFUSE - is
|
|
* ABB enable/disable flag and VSET value, which must be copied
|
|
* to LDOVBB register. If function call fails - return quietly,
|
|
* it means no ABB is required for such silicon.
|
|
*
|
|
* For silicons, which don't require LDOVBB setup "fuse" and
|
|
* "ldovbb" offsets are not defined. ABB will be initialized in
|
|
* the common way for them.
|
|
*/
|
|
if (fuse && ldovbb) {
|
|
if (abb_setup_ldovbb(fuse, ldovbb))
|
|
return;
|
|
}
|
|
|
|
/* clear ABB registers */
|
|
writel(0, setup);
|
|
writel(0, control);
|
|
|
|
/* configure timings, based on oscillator value */
|
|
abb_setup_timings(setup);
|
|
|
|
/* clear pending interrupts before setup */
|
|
setbits_le32(txdone, txdone_mask);
|
|
|
|
/* select ABB type */
|
|
setbits_le32(setup, abb_type_mask | OMAP_ABB_SETUP_SR2EN_MASK);
|
|
|
|
/* initiate ABB ldo change */
|
|
setbits_le32(control, opp_sel_mask | OMAP_ABB_CONTROL_OPP_CHANGE_MASK);
|
|
|
|
/* wait until transition complete */
|
|
if (!wait_on_value(txdone_mask, txdone_mask, (void *)txdone, LDELAY))
|
|
puts("Error: ABB txdone is not set\n");
|
|
|
|
/* clear ABB tranxdone */
|
|
setbits_le32(txdone, txdone_mask);
|
|
}
|