mirror of
https://github.com/u-boot/u-boot.git
synced 2024-12-15 15:53:26 +08:00
a9221f3ebd
Enable the extended ENV options for AT91 and OMAP2PLUS in order to be
able to use CONFIG_ENV_UBI_* on these architectures.
As this change also makes the configs ENV_SIZE, ENV_SECT_SIZE,
ENV_OFFSET visible to AT91 and OMAP2PLUS, migrate users of these to
KConfig.
This migration was run using an extended moveconfig.py which evaluates
expressions such as "(512 << 10)". See patch ("moveconfig: expand
simple expressions").
All modified boards were built with SOURCE_DATE_EPOCH=0 before and
after the change and successfully confirmed that the identical binary
is generated (the only exception was igep00x0, which does not define
CONFIG_ENV_IS_IN_UBI in the original board header. Once that is
defined, the test passes too).
hs: rebased patch to:
68b90e57bc: "configs: tinker-rk3288 disable CONFIG_SPL_I2C_SUPPORT"
Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Tom Rini <trini@konsulko.com>
327 lines
9.6 KiB
C
327 lines
9.6 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* Copyright (C) 2011
|
|
* Stefano Babic, DENX Software Engineering, sbabic@denx.de.
|
|
*
|
|
* Copyright (C) 2009 TechNexion Ltd.
|
|
*/
|
|
|
|
#ifndef __TAM3517_H
|
|
#define __TAM3517_H
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
*/
|
|
|
|
#include <asm/arch/cpu.h> /* get chip and board defs */
|
|
#include <asm/arch/omap.h>
|
|
|
|
/* Clock Defines */
|
|
#define V_OSCK 26000000 /* Clock output from T2 */
|
|
#define V_SCLK (V_OSCK >> 1)
|
|
|
|
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
|
|
#define CONFIG_SETUP_MEMORY_TAGS
|
|
#define CONFIG_INITRD_TAG
|
|
#define CONFIG_REVISION_TAG
|
|
|
|
/*
|
|
* Size of malloc() pool
|
|
*/
|
|
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10) + \
|
|
2 * 1024 * 1024)
|
|
/*
|
|
* DDR related
|
|
*/
|
|
#define CONFIG_SYS_CS0_SIZE (256 * 1024 * 1024)
|
|
|
|
/*
|
|
* Hardware drivers
|
|
*/
|
|
|
|
/*
|
|
* NS16550 Configuration
|
|
*/
|
|
#define CONFIG_SYS_NS16550_SERIAL
|
|
#define CONFIG_SYS_NS16550_REG_SIZE (-4)
|
|
#define CONFIG_SYS_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
|
|
|
|
/*
|
|
* select serial console configuration
|
|
*/
|
|
#define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1
|
|
|
|
/* allow to overwrite serial and ethaddr */
|
|
#define CONFIG_ENV_OVERWRITE
|
|
#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
|
|
115200}
|
|
/* EHCI */
|
|
#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 25
|
|
|
|
#define CONFIG_SYS_I2C
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* base address */
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
|
|
|
|
/*
|
|
* Board NAND Info.
|
|
*/
|
|
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
|
|
/* to access */
|
|
/* nand at CS0 */
|
|
|
|
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of */
|
|
/* NAND devices */
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
|
|
|
|
#define CONFIG_SYS_MAXARGS 32 /* max number of command */
|
|
/* args */
|
|
/* memtest works on */
|
|
#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0)
|
|
#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
|
|
0x01F00000) /* 31MB */
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default load */
|
|
/* address */
|
|
|
|
/*
|
|
* AM3517 has 12 GP timers, they can be driven by the system clock
|
|
* (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
|
|
* This rate is divided by a local divisor.
|
|
*/
|
|
#define CONFIG_SYS_TIMERBASE OMAP34XX_GPT2
|
|
#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
|
|
|
|
/*
|
|
* Physical Memory Map
|
|
*/
|
|
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
|
|
#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
|
|
|
|
/*
|
|
* FLASH and environment organization
|
|
*/
|
|
|
|
/* **** PISMO SUPPORT *** */
|
|
|
|
/* Redundant Environment */
|
|
#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
|
|
#define CONFIG_ENV_OFFSET 0x180000
|
|
#define CONFIG_ENV_ADDR 0x180000
|
|
#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \
|
|
2 * CONFIG_SYS_ENV_SECT_SIZE)
|
|
#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
|
|
|
|
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
|
|
#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
|
|
#define CONFIG_SYS_INIT_RAM_SIZE 0x800
|
|
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
|
|
CONFIG_SYS_INIT_RAM_SIZE - \
|
|
GENERATED_GBL_DATA_SIZE)
|
|
|
|
/*
|
|
* ethernet support, EMAC
|
|
*
|
|
*/
|
|
#define CONFIG_DRIVER_TI_EMAC_USE_RMII
|
|
#define CONFIG_BOOTP_DNS2
|
|
#define CONFIG_BOOTP_SEND_HOSTNAME
|
|
#define CONFIG_NET_RETRY_COUNT 10
|
|
|
|
/* Defines for SPL */
|
|
#define CONFIG_SPL_CONSOLE
|
|
#define CONFIG_SPL_NAND_SOFTECC
|
|
#define CONFIG_SPL_NAND_WORKSPACE 0x8f07f000 /* below BSS */
|
|
|
|
#define CONFIG_SPL_NAND_BASE
|
|
#define CONFIG_SPL_NAND_DRIVERS
|
|
#define CONFIG_SPL_NAND_ECC
|
|
|
|
#define CONFIG_SPL_MAX_SIZE (SRAM_SCRATCH_SPACE_ADDR - \
|
|
CONFIG_SPL_TEXT_BASE)
|
|
#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK
|
|
|
|
#define CONFIG_SYS_SPL_MALLOC_START 0x8f000000
|
|
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000
|
|
#define CONFIG_SPL_BSS_START_ADDR 0x8f080000 /* end of RAM */
|
|
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
|
|
|
|
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
|
|
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
|
|
|
|
/* FAT */
|
|
#define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage"
|
|
#define CONFIG_SPL_FS_LOAD_ARGS_NAME "args"
|
|
|
|
/* RAW SD card / eMMC */
|
|
#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900 /* address 0x120000 */
|
|
#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x80 /* address 0x10000 */
|
|
#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x80 /* 64KiB */
|
|
|
|
/* NAND boot config */
|
|
#define CONFIG_SYS_NAND_PAGE_COUNT 64
|
|
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
|
|
#define CONFIG_SYS_NAND_OOBSIZE 64
|
|
#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
|
|
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
|
|
#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
|
|
#define CONFIG_SYS_NAND_ECCPOS {40, 41, 42, 43, 44, 45, 46, 47,\
|
|
48, 49, 50, 51, 52, 53, 54, 55,\
|
|
56, 57, 58, 59, 60, 61, 62, 63}
|
|
#define CONFIG_SYS_NAND_ECCSIZE 256
|
|
#define CONFIG_SYS_NAND_ECCBYTES 3
|
|
#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_SW
|
|
|
|
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
|
|
|
|
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
|
|
#define CONFIG_SYS_NAND_U_BOOT_SIZE 0x80000
|
|
|
|
/* Setup MTD for NAND on the SOM */
|
|
|
|
#define CONFIG_TAM3517_SETTINGS \
|
|
"netdev=eth0\0" \
|
|
"nandargs=setenv bootargs root=${nandroot} " \
|
|
"rootfstype=${nandrootfstype}\0" \
|
|
"nfsargs=setenv bootargs root=/dev/nfs rw " \
|
|
"nfsroot=${serverip}:${rootpath}\0" \
|
|
"ramargs=setenv bootargs root=/dev/ram rw\0" \
|
|
"addip_sta=setenv bootargs ${bootargs} " \
|
|
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
|
|
":${hostname}:${netdev}:off panic=1\0" \
|
|
"addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0" \
|
|
"addip=if test -n ${ipdyn};then run addip_dyn;" \
|
|
"else run addip_sta;fi\0" \
|
|
"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
|
|
"addtty=setenv bootargs ${bootargs}" \
|
|
" console=ttyO0,${baudrate}\0" \
|
|
"addmisc=setenv bootargs ${bootargs} ${misc}\0" \
|
|
"loadaddr=82000000\0" \
|
|
"kernel_addr_r=82000000\0" \
|
|
"hostname=" CONFIG_HOSTNAME "\0" \
|
|
"bootfile=" CONFIG_HOSTNAME "/uImage\0" \
|
|
"flash_self=run ramargs addip addtty addmtd addmisc;" \
|
|
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
|
|
"flash_nfs=run nfsargs addip addtty addmtd addmisc;" \
|
|
"bootm ${kernel_addr}\0" \
|
|
"nandboot=run nandargs addip addtty addmtd addmisc;" \
|
|
"nand read ${kernel_addr_r} kernel\0" \
|
|
"bootm ${kernel_addr_r}\0" \
|
|
"net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
|
|
"run nfsargs addip addtty addmtd addmisc;" \
|
|
"bootm ${kernel_addr_r}\0" \
|
|
"net_self=if run net_self_load;then " \
|
|
"run ramargs addip addtty addmtd addmisc;" \
|
|
"bootm ${kernel_addr_r} ${ramdisk_addr_r};" \
|
|
"else echo Images not loades;fi\0" \
|
|
"u-boot=" CONFIG_HOSTNAME "/u-boot.img\0" \
|
|
"load=tftp ${loadaddr} ${u-boot}\0" \
|
|
"loadmlo=tftp ${loadaddr} ${mlo}\0" \
|
|
"mlo=" CONFIG_HOSTNAME "/MLO\0" \
|
|
"uboot_addr=0x80000\0" \
|
|
"update=nandecc sw;nand erase ${uboot_addr} 100000;" \
|
|
"nand write ${loadaddr} ${uboot_addr} 80000\0" \
|
|
"updatemlo=nandecc hw;nand erase 0 20000;" \
|
|
"nand write ${loadaddr} 0 20000\0" \
|
|
"upd=if run load;then echo Updating u-boot;if run update;" \
|
|
"then echo U-Boot updated;" \
|
|
"else echo Error updating u-boot !;" \
|
|
"echo Board without bootloader !!;" \
|
|
"fi;" \
|
|
"else echo U-Boot not downloaded..exiting;fi\0" \
|
|
|
|
/*
|
|
* this is common code for all TAM3517 boards.
|
|
* MAC address is stored from manufacturer in
|
|
* I2C EEPROM
|
|
*/
|
|
#if !(defined(__KERNEL_STRICT_NAMES) || defined(__ASSEMBLY__))
|
|
/*
|
|
* The I2C EEPROM on the TAM3517 contains
|
|
* mac address and production data
|
|
*/
|
|
struct tam3517_module_info {
|
|
char customer[48];
|
|
char product[48];
|
|
|
|
/*
|
|
* bit 0~47 : sequence number
|
|
* bit 48~55 : week of year, from 0.
|
|
* bit 56~63 : year
|
|
*/
|
|
unsigned long long sequence_number;
|
|
|
|
/*
|
|
* bit 0~7 : revision fixed
|
|
* bit 8~15 : revision major
|
|
* bit 16~31 : TNxxx
|
|
*/
|
|
unsigned int revision;
|
|
unsigned char eth_addr[4][8];
|
|
unsigned char _rev[100];
|
|
};
|
|
|
|
#define TAM3517_READ_EEPROM(info, ret) \
|
|
do { \
|
|
i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); \
|
|
if (eeprom_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, \
|
|
(void *)info, sizeof(*info))) \
|
|
ret = 1; \
|
|
else \
|
|
ret = 0; \
|
|
} while (0)
|
|
|
|
#define TAM3517_READ_MAC_FROM_EEPROM(info) \
|
|
do { \
|
|
char buf[80], ethname[20]; \
|
|
int i; \
|
|
memset(buf, 0, sizeof(buf)); \
|
|
for (i = 0 ; i < ARRAY_SIZE((info)->eth_addr); i++) { \
|
|
sprintf(buf, "%02X:%02X:%02X:%02X:%02X:%02X", \
|
|
(info)->eth_addr[i][5], \
|
|
(info)->eth_addr[i][4], \
|
|
(info)->eth_addr[i][3], \
|
|
(info)->eth_addr[i][2], \
|
|
(info)->eth_addr[i][1], \
|
|
(info)->eth_addr[i][0]); \
|
|
\
|
|
if (i) \
|
|
sprintf(ethname, "eth%daddr", i); \
|
|
else \
|
|
strcpy(ethname, "ethaddr"); \
|
|
printf("Setting %s from EEPROM with %s\n", ethname, buf);\
|
|
env_set(ethname, buf); \
|
|
} \
|
|
} while (0)
|
|
|
|
/* The following macros are taken from Technexion's documentation */
|
|
#define TAM3517_sequence_number(info) \
|
|
((info)->sequence_number % 0x1000000000000LL)
|
|
#define TAM3517_week_of_year(info) (((info)->sequence_number >> 48) % 0x100)
|
|
#define TAM3517_year(info) ((info)->sequence_number >> 56)
|
|
#define TAM3517_revision_fixed(info) ((info)->revision % 0x100)
|
|
#define TAM3517_revision_major(info) (((info)->revision >> 8) % 0x100)
|
|
#define TAM3517_revision_tn(info) ((info)->revision >> 16)
|
|
|
|
#define TAM3517_PRINT_SOM_INFO(info) \
|
|
do { \
|
|
printf("Vendor:%s\n", (info)->customer); \
|
|
printf("SOM: %s\n", (info)->product); \
|
|
printf("SeqNr: %02llu%02llu%012llu\n", \
|
|
TAM3517_year(info), \
|
|
TAM3517_week_of_year(info), \
|
|
TAM3517_sequence_number(info)); \
|
|
printf("Rev: TN%u %u.%u\n", \
|
|
TAM3517_revision_tn(info), \
|
|
TAM3517_revision_major(info), \
|
|
TAM3517_revision_fixed(info)); \
|
|
} while (0)
|
|
|
|
#endif
|
|
|
|
#endif /* __TAM3517_H */
|