mirror of
https://github.com/u-boot/u-boot.git
synced 2024-12-15 15:53:26 +08:00
654e4e70d4
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM I2C API when DM_I2C is used.When DM_I2C_COMPAT is not enabled for compilation, a compilation error will be generated. This patch solves the problem that the i2c-related api of the ls2088a platform does not support dm. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
605 lines
20 KiB
C
605 lines
20 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* Copyright 2017, 2019 NXP
|
|
* Copyright 2015 Freescale Semiconductor
|
|
*/
|
|
|
|
#ifndef __LS2_RDB_H
|
|
#define __LS2_RDB_H
|
|
|
|
#include "ls2080a_common.h"
|
|
|
|
#ifdef CONFIG_FSL_QSPI
|
|
#ifdef CONFIG_TARGET_LS2081ARDB
|
|
#define CONFIG_QIXIS_I2C_ACCESS
|
|
#endif
|
|
#ifndef CONFIG_DM_I2C
|
|
#define CONFIG_SYS_I2C_EARLY_INIT
|
|
#endif
|
|
#endif
|
|
|
|
#define I2C_MUX_CH_VOL_MONITOR 0xa
|
|
#define I2C_VOL_MONITOR_ADDR 0x38
|
|
#define CONFIG_VOL_MONITOR_IR36021_READ
|
|
#define CONFIG_VOL_MONITOR_IR36021_SET
|
|
|
|
#define CONFIG_VID_FLS_ENV "ls2080ardb_vdd_mv"
|
|
#ifndef CONFIG_SPL_BUILD
|
|
#define CONFIG_VID
|
|
#endif
|
|
/* step the IR regulator in 5mV increments */
|
|
#define IR_VDD_STEP_DOWN 5
|
|
#define IR_VDD_STEP_UP 5
|
|
/* The lowest and highest voltage allowed for LS2080ARDB */
|
|
#define VDD_MV_MIN 819
|
|
#define VDD_MV_MAX 1212
|
|
|
|
#ifndef __ASSEMBLY__
|
|
unsigned long get_board_sys_clk(void);
|
|
#endif
|
|
|
|
#define CONFIG_SYS_CLK_FREQ get_board_sys_clk()
|
|
#define CONFIG_DDR_CLK_FREQ 133333333
|
|
#define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ/4)
|
|
|
|
#define CONFIG_DDR_SPD
|
|
#define CONFIG_DDR_ECC
|
|
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
|
|
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
|
|
#define SPD_EEPROM_ADDRESS1 0x51
|
|
#define SPD_EEPROM_ADDRESS2 0x52
|
|
#define SPD_EEPROM_ADDRESS3 0x53
|
|
#define SPD_EEPROM_ADDRESS4 0x54
|
|
#define SPD_EEPROM_ADDRESS5 0x55
|
|
#define SPD_EEPROM_ADDRESS6 0x56 /* dummy address */
|
|
#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1
|
|
#define CONFIG_SYS_SPD_BUS_NUM 0 /* SPD on I2C bus 0 */
|
|
#define CONFIG_DIMM_SLOTS_PER_CTLR 2
|
|
#define CONFIG_CHIP_SELECTS_PER_CTRL 4
|
|
#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
|
|
#define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR 1
|
|
#endif
|
|
|
|
/* SATA */
|
|
#define CONFIG_SCSI_AHCI_PLAT
|
|
|
|
#define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1
|
|
#define CONFIG_SYS_SATA2 AHCI_BASE_ADDR2
|
|
|
|
#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
|
|
#define CONFIG_SYS_SCSI_MAX_LUN 1
|
|
#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
|
|
CONFIG_SYS_SCSI_MAX_LUN)
|
|
#ifdef CONFIG_TFABOOT
|
|
#define CONFIG_SYS_MMC_ENV_DEV 0
|
|
|
|
#define CONFIG_ENV_SIZE 0x2000
|
|
#define CONFIG_ENV_OFFSET 0x500000 /* 5MB */
|
|
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + \
|
|
CONFIG_ENV_OFFSET)
|
|
#define CONFIG_ENV_SECT_SIZE 0x40000
|
|
#endif
|
|
|
|
#if !defined(CONFIG_FSL_QSPI) || defined(CONFIG_TFABOOT)
|
|
|
|
#define CONFIG_SYS_NOR0_CSPR_EXT (0x0)
|
|
#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
|
|
#define CONFIG_SYS_NOR_AMASK_EARLY IFC_AMASK(64*1024*1024)
|
|
|
|
#define CONFIG_SYS_NOR0_CSPR \
|
|
(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
|
|
CSPR_PORT_SIZE_16 | \
|
|
CSPR_MSEL_NOR | \
|
|
CSPR_V)
|
|
#define CONFIG_SYS_NOR0_CSPR_EARLY \
|
|
(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY) | \
|
|
CSPR_PORT_SIZE_16 | \
|
|
CSPR_MSEL_NOR | \
|
|
CSPR_V)
|
|
#define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(12)
|
|
#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \
|
|
FTIM0_NOR_TEADC(0x5) | \
|
|
FTIM0_NOR_TEAHC(0x5))
|
|
#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \
|
|
FTIM1_NOR_TRAD_NOR(0x1a) |\
|
|
FTIM1_NOR_TSEQRAD_NOR(0x13))
|
|
#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \
|
|
FTIM2_NOR_TCH(0x4) | \
|
|
FTIM2_NOR_TWPH(0x0E) | \
|
|
FTIM2_NOR_TWP(0x1c))
|
|
#define CONFIG_SYS_NOR_FTIM3 0x04000000
|
|
#define CONFIG_SYS_IFC_CCR 0x01000000
|
|
|
|
#ifdef CONFIG_MTD_NOR_FLASH
|
|
#define CONFIG_SYS_FLASH_QUIET_TEST
|
|
#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
|
|
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
|
|
|
|
#define CONFIG_SYS_FLASH_EMPTY_INFO
|
|
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE,\
|
|
CONFIG_SYS_FLASH_BASE + 0x40000000}
|
|
#endif
|
|
|
|
#define CONFIG_NAND_FSL_IFC
|
|
#define CONFIG_SYS_NAND_MAX_ECCPOS 256
|
|
#define CONFIG_SYS_NAND_MAX_OOBFREE 2
|
|
|
|
#define CONFIG_SYS_NAND_CSPR_EXT (0x0)
|
|
#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
|
|
| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
|
|
| CSPR_MSEL_NAND /* MSEL = NAND */ \
|
|
| CSPR_V)
|
|
#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024)
|
|
|
|
#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
|
|
| CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
|
|
| CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
|
|
| CSOR_NAND_RAL_3 /* RAL = 3Byes */ \
|
|
| CSOR_NAND_PGS_4K /* Page Size = 4K */ \
|
|
| CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \
|
|
| CSOR_NAND_PB(128)) /* Pages Per Block 128*/
|
|
|
|
#define CONFIG_SYS_NAND_ONFI_DETECTION
|
|
|
|
/* ONFI NAND Flash mode0 Timing Params */
|
|
#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x0e) | \
|
|
FTIM0_NAND_TWP(0x30) | \
|
|
FTIM0_NAND_TWCHT(0x0e) | \
|
|
FTIM0_NAND_TWH(0x14))
|
|
#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x64) | \
|
|
FTIM1_NAND_TWBE(0xab) | \
|
|
FTIM1_NAND_TRR(0x1c) | \
|
|
FTIM1_NAND_TRP(0x30))
|
|
#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x1e) | \
|
|
FTIM2_NAND_TREH(0x14) | \
|
|
FTIM2_NAND_TWHRE(0x3c))
|
|
#define CONFIG_SYS_NAND_FTIM3 0x0
|
|
|
|
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
|
|
#define CONFIG_SYS_MAX_NAND_DEVICE 1
|
|
#define CONFIG_MTD_NAND_VERIFY_WRITE
|
|
|
|
#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024)
|
|
#define CONFIG_FSL_QIXIS /* use common QIXIS code */
|
|
#define QIXIS_LBMAP_SWITCH 0x06
|
|
#define QIXIS_LBMAP_MASK 0x0f
|
|
#define QIXIS_LBMAP_SHIFT 0
|
|
#define QIXIS_LBMAP_DFLTBANK 0x00
|
|
#define QIXIS_LBMAP_ALTBANK 0x04
|
|
#define QIXIS_LBMAP_NAND 0x09
|
|
#define QIXIS_RST_CTL_RESET 0x31
|
|
#define QIXIS_RST_CTL_RESET_EN 0x30
|
|
#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
|
|
#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
|
|
#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
|
|
#define QIXIS_RCW_SRC_NAND 0x119
|
|
#define QIXIS_RST_FORCE_MEM 0x01
|
|
|
|
#define CONFIG_SYS_CSPR3_EXT (0x0)
|
|
#define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \
|
|
| CSPR_PORT_SIZE_8 \
|
|
| CSPR_MSEL_GPCM \
|
|
| CSPR_V)
|
|
#define CONFIG_SYS_CSPR3_FINAL (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
|
|
| CSPR_PORT_SIZE_8 \
|
|
| CSPR_MSEL_GPCM \
|
|
| CSPR_V)
|
|
|
|
#define CONFIG_SYS_AMASK3 IFC_AMASK(64*1024)
|
|
#define CONFIG_SYS_CSOR3 CSOR_GPCM_ADM_SHIFT(12)
|
|
/* QIXIS Timing parameters for IFC CS3 */
|
|
#define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \
|
|
FTIM0_GPCM_TEADC(0x0e) | \
|
|
FTIM0_GPCM_TEAHC(0x0e))
|
|
#define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) | \
|
|
FTIM1_GPCM_TRAD(0x3f))
|
|
#define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0xf) | \
|
|
FTIM2_GPCM_TCH(0xf) | \
|
|
FTIM2_GPCM_TWP(0x3E))
|
|
#define CONFIG_SYS_CS3_FTIM3 0x0
|
|
|
|
#if defined(CONFIG_SPL) && defined(CONFIG_NAND)
|
|
#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR0_CSPR_EXT
|
|
#define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR0_CSPR_EARLY
|
|
#define CONFIG_SYS_CSPR2_FINAL CONFIG_SYS_NOR0_CSPR
|
|
#define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK
|
|
#define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR
|
|
#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0
|
|
#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1
|
|
#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2
|
|
#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3
|
|
#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
|
|
#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
|
|
#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
|
|
#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
|
|
#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
|
|
#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
|
|
#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
|
|
#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
|
|
|
|
#ifndef CONFIG_TFABOOT
|
|
#define CONFIG_ENV_OFFSET (2048 * 1024)
|
|
#define CONFIG_ENV_SECT_SIZE 0x20000
|
|
#define CONFIG_ENV_SIZE 0x2000
|
|
#endif
|
|
#define CONFIG_SPL_PAD_TO 0x80000
|
|
#define CONFIG_SYS_NAND_U_BOOT_OFFS (1024 * 1024)
|
|
#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 * 1024)
|
|
#else
|
|
#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
|
|
#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR_EARLY
|
|
#define CONFIG_SYS_CSPR0_FINAL CONFIG_SYS_NOR0_CSPR
|
|
#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
|
|
#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
|
|
#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
|
|
#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
|
|
#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
|
|
#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
|
|
#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT
|
|
#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR
|
|
#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK
|
|
#define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR
|
|
#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0
|
|
#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1
|
|
#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2
|
|
#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3
|
|
|
|
#ifndef CONFIG_TFABOOT
|
|
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x300000)
|
|
#define CONFIG_ENV_SECT_SIZE 0x20000
|
|
#define CONFIG_ENV_SIZE 0x2000
|
|
#endif
|
|
#endif
|
|
|
|
/* Debug Server firmware */
|
|
#define CONFIG_SYS_DEBUG_SERVER_FW_IN_NOR
|
|
#define CONFIG_SYS_DEBUG_SERVER_FW_ADDR 0x580D00000ULL
|
|
#endif
|
|
#define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
|
|
|
|
#ifdef CONFIG_TARGET_LS2081ARDB
|
|
#define CONFIG_FSL_QIXIS /* use common QIXIS code */
|
|
#define QIXIS_QMAP_MASK 0x07
|
|
#define QIXIS_QMAP_SHIFT 5
|
|
#define QIXIS_LBMAP_DFLTBANK 0x00
|
|
#define QIXIS_LBMAP_QSPI 0x00
|
|
#define QIXIS_RCW_SRC_QSPI 0x62
|
|
#define QIXIS_LBMAP_ALTBANK 0x20
|
|
#define QIXIS_RST_CTL_RESET 0x31
|
|
#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
|
|
#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
|
|
#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
|
|
#define QIXIS_LBMAP_MASK 0x0f
|
|
#define QIXIS_RST_CTL_RESET_EN 0x30
|
|
#endif
|
|
|
|
/*
|
|
* I2C
|
|
*/
|
|
#ifdef CONFIG_TARGET_LS2081ARDB
|
|
#define CONFIG_SYS_I2C_FPGA_ADDR 0x66
|
|
#endif
|
|
#define I2C_MUX_PCA_ADDR 0x75
|
|
#define I2C_MUX_PCA_ADDR_PRI 0x75 /* Primary Mux*/
|
|
|
|
/* I2C bus multiplexer */
|
|
#define I2C_MUX_CH_DEFAULT 0x8
|
|
|
|
/* SPI */
|
|
#if defined(CONFIG_FSL_QSPI) || defined(CONFIG_FSL_DSPI)
|
|
#ifdef CONFIG_FSL_DSPI
|
|
#define CONFIG_SPI_FLASH_STMICRO
|
|
#endif
|
|
#define FSL_QSPI_FLASH_SIZE SZ_64M /* 64MB */
|
|
#define FSL_QSPI_FLASH_NUM 2
|
|
#endif
|
|
|
|
/*
|
|
* RTC configuration
|
|
*/
|
|
#define RTC
|
|
#ifdef CONFIG_TARGET_LS2081ARDB
|
|
#define CONFIG_RTC_PCF8563 1
|
|
#define CONFIG_SYS_I2C_RTC_ADDR 0x51
|
|
#else
|
|
#define CONFIG_RTC_DS3231 1
|
|
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
|
|
#endif
|
|
|
|
/* EEPROM */
|
|
#define CONFIG_ID_EEPROM
|
|
#define CONFIG_SYS_I2C_EEPROM_NXID
|
|
#define CONFIG_SYS_EEPROM_BUS_NUM 0
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
|
|
|
|
#define CONFIG_FSL_MEMAC
|
|
|
|
#ifdef CONFIG_PCI
|
|
#define CONFIG_PCI_SCAN_SHOW
|
|
#endif
|
|
|
|
/* MMC */
|
|
#ifdef CONFIG_MMC
|
|
#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
|
|
#endif
|
|
|
|
#define BOOT_TARGET_DEVICES(func) \
|
|
func(USB, usb, 0) \
|
|
func(MMC, mmc, 0) \
|
|
func(SCSI, scsi, 0) \
|
|
func(DHCP, dhcp, na)
|
|
#include <config_distro_bootcmd.h>
|
|
|
|
#ifdef CONFIG_TFABOOT
|
|
#define QSPI_MC_INIT_CMD \
|
|
"env exists secureboot && " \
|
|
"esbc_validate 0x20700000 && " \
|
|
"esbc_validate 0x20740000;" \
|
|
"fsl_mc start mc 0x20a00000 0x20e00000 \0"
|
|
#define SD_MC_INIT_CMD \
|
|
"mmcinfo;mmc read 0x80a00000 0x5000 0x1200;" \
|
|
"mmc read 0x80e00000 0x7000 0x800;" \
|
|
"env exists secureboot && " \
|
|
"mmc read 0x80700000 0x3800 0x10 && " \
|
|
"mmc read 0x80740000 0x3A00 0x10 && " \
|
|
"esbc_validate 0x80700000 && " \
|
|
"esbc_validate 0x80740000 ;" \
|
|
"fsl_mc start mc 0x80a00000 0x80e00000\0"
|
|
#define IFC_MC_INIT_CMD \
|
|
"env exists secureboot && " \
|
|
"esbc_validate 0x580700000 && " \
|
|
"esbc_validate 0x580740000; " \
|
|
"fsl_mc start mc 0x580a00000 0x580e00000 \0"
|
|
#else
|
|
#ifdef CONFIG_QSPI_BOOT
|
|
#define MC_INIT_CMD \
|
|
"mcinitcmd=env exists secureboot && " \
|
|
"esbc_validate 0x20700000 && " \
|
|
"esbc_validate 0x20740000;" \
|
|
"fsl_mc start mc 0x20a00000 0x20e00000 \0"
|
|
#elif defined(CONFIG_SD_BOOT)
|
|
#define MC_INIT_CMD \
|
|
"mcinitcmd=mmcinfo;mmc read 0x80000000 0x5000 0x800;" \
|
|
"mmc read 0x80100000 0x7000 0x800;" \
|
|
"env exists secureboot && " \
|
|
"mmc read 0x80700000 0x3800 0x10 && " \
|
|
"mmc read 0x80740000 0x3A00 0x10 && " \
|
|
"esbc_validate 0x80700000 && " \
|
|
"esbc_validate 0x80740000 ;" \
|
|
"fsl_mc start mc 0x80000000 0x80100000\0" \
|
|
"mcmemsize=0x70000000\0"
|
|
#else
|
|
#define MC_INIT_CMD \
|
|
"mcinitcmd=env exists secureboot && " \
|
|
"esbc_validate 0x580700000 && " \
|
|
"esbc_validate 0x580740000; " \
|
|
"fsl_mc start mc 0x580a00000 0x580e00000 \0"
|
|
#endif
|
|
#endif
|
|
|
|
/* Initial environment variables */
|
|
#undef CONFIG_EXTRA_ENV_SETTINGS
|
|
#ifdef CONFIG_TFABOOT
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
|
|
"ramdisk_addr=0x800000\0" \
|
|
"ramdisk_size=0x2000000\0" \
|
|
"fdt_high=0xa0000000\0" \
|
|
"initrd_high=0xffffffffffffffff\0" \
|
|
"fdt_addr=0x64f00000\0" \
|
|
"kernel_addr=0x581000000\0" \
|
|
"kernel_start=0x1000000\0" \
|
|
"kernelheader_start=0x800000\0" \
|
|
"scriptaddr=0x80000000\0" \
|
|
"scripthdraddr=0x80080000\0" \
|
|
"fdtheader_addr_r=0x80100000\0" \
|
|
"kernelheader_addr_r=0x80200000\0" \
|
|
"kernelheader_addr=0x580800000\0" \
|
|
"kernel_addr_r=0x81000000\0" \
|
|
"kernelheader_size=0x40000\0" \
|
|
"fdt_addr_r=0x90000000\0" \
|
|
"load_addr=0xa0000000\0" \
|
|
"kernel_size=0x2800000\0" \
|
|
"kernel_addr_sd=0x8000\0" \
|
|
"kernel_size_sd=0x14000\0" \
|
|
"console=ttyAMA0,38400n8\0" \
|
|
"mcmemsize=0x70000000\0" \
|
|
"sd_bootcmd=echo Trying load from SD ..;" \
|
|
"mmcinfo; mmc read $load_addr " \
|
|
"$kernel_addr_sd $kernel_size_sd && " \
|
|
"bootm $load_addr#$board\0" \
|
|
QSPI_MC_INIT_CMD \
|
|
BOOTENV \
|
|
"boot_scripts=ls2088ardb_boot.scr\0" \
|
|
"boot_script_hdr=hdr_ls2088ardb_bs.out\0" \
|
|
"scan_dev_for_boot_part=" \
|
|
"part list ${devtype} ${devnum} devplist; " \
|
|
"env exists devplist || setenv devplist 1; " \
|
|
"for distro_bootpart in ${devplist}; do " \
|
|
"if fstype ${devtype} " \
|
|
"${devnum}:${distro_bootpart} " \
|
|
"bootfstype; then " \
|
|
"run scan_dev_for_boot; " \
|
|
"fi; " \
|
|
"done\0" \
|
|
"boot_a_script=" \
|
|
"load ${devtype} ${devnum}:${distro_bootpart} " \
|
|
"${scriptaddr} ${prefix}${script}; " \
|
|
"env exists secureboot && load ${devtype} " \
|
|
"${devnum}:${distro_bootpart} " \
|
|
"${scripthdraddr} ${prefix}${boot_script_hdr} " \
|
|
"&& esbc_validate ${scripthdraddr};" \
|
|
"source ${scriptaddr}\0" \
|
|
"qspi_bootcmd=echo Trying load from qspi..;" \
|
|
"sf probe && sf read $load_addr " \
|
|
"$kernel_start $kernel_size ; env exists secureboot &&" \
|
|
"sf read $kernelheader_addr_r $kernelheader_start " \
|
|
"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
|
|
" bootm $load_addr#$board\0" \
|
|
"nor_bootcmd=echo Trying load from nor..;" \
|
|
"cp.b $kernel_addr $load_addr " \
|
|
"$kernel_size ; env exists secureboot && " \
|
|
"cp.b $kernelheader_addr $kernelheader_addr_r " \
|
|
"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
|
|
"bootm $load_addr#$board\0"
|
|
#else
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
|
|
"ramdisk_addr=0x800000\0" \
|
|
"ramdisk_size=0x2000000\0" \
|
|
"fdt_high=0xa0000000\0" \
|
|
"initrd_high=0xffffffffffffffff\0" \
|
|
"fdt_addr=0x64f00000\0" \
|
|
"kernel_addr=0x581000000\0" \
|
|
"kernel_start=0x1000000\0" \
|
|
"kernelheader_start=0x800000\0" \
|
|
"scriptaddr=0x80000000\0" \
|
|
"scripthdraddr=0x80080000\0" \
|
|
"fdtheader_addr_r=0x80100000\0" \
|
|
"kernelheader_addr_r=0x80200000\0" \
|
|
"kernelheader_addr=0x580800000\0" \
|
|
"kernel_addr_r=0x81000000\0" \
|
|
"kernelheader_size=0x40000\0" \
|
|
"fdt_addr_r=0x90000000\0" \
|
|
"load_addr=0xa0000000\0" \
|
|
"kernel_size=0x2800000\0" \
|
|
"kernel_addr_sd=0x8000\0" \
|
|
"kernel_size_sd=0x14000\0" \
|
|
"console=ttyAMA0,38400n8\0" \
|
|
"mcmemsize=0x70000000\0" \
|
|
"sd_bootcmd=echo Trying load from SD ..;" \
|
|
"mmcinfo; mmc read $load_addr " \
|
|
"$kernel_addr_sd $kernel_size_sd && " \
|
|
"bootm $load_addr#$board\0" \
|
|
MC_INIT_CMD \
|
|
BOOTENV \
|
|
"boot_scripts=ls2088ardb_boot.scr\0" \
|
|
"boot_script_hdr=hdr_ls2088ardb_bs.out\0" \
|
|
"scan_dev_for_boot_part=" \
|
|
"part list ${devtype} ${devnum} devplist; " \
|
|
"env exists devplist || setenv devplist 1; " \
|
|
"for distro_bootpart in ${devplist}; do " \
|
|
"if fstype ${devtype} " \
|
|
"${devnum}:${distro_bootpart} " \
|
|
"bootfstype; then " \
|
|
"run scan_dev_for_boot; " \
|
|
"fi; " \
|
|
"done\0" \
|
|
"boot_a_script=" \
|
|
"load ${devtype} ${devnum}:${distro_bootpart} " \
|
|
"${scriptaddr} ${prefix}${script}; " \
|
|
"env exists secureboot && load ${devtype} " \
|
|
"${devnum}:${distro_bootpart} " \
|
|
"${scripthdraddr} ${prefix}${boot_script_hdr}; " \
|
|
"env exists secureboot " \
|
|
"&& esbc_validate ${scripthdraddr};" \
|
|
"source ${scriptaddr}\0" \
|
|
"qspi_bootcmd=echo Trying load from qspi..;" \
|
|
"sf probe && sf read $load_addr " \
|
|
"$kernel_start $kernel_size ; env exists secureboot &&" \
|
|
"sf read $kernelheader_addr_r $kernelheader_start " \
|
|
"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
|
|
" bootm $load_addr#$board\0" \
|
|
"nor_bootcmd=echo Trying load from nor..;" \
|
|
"cp.b $kernel_addr $load_addr " \
|
|
"$kernel_size ; env exists secureboot && " \
|
|
"cp.b $kernelheader_addr $kernelheader_addr_r " \
|
|
"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
|
|
"bootm $load_addr#$board\0"
|
|
#endif
|
|
|
|
#ifdef CONFIG_TFABOOT
|
|
#define QSPI_NOR_BOOTCOMMAND \
|
|
"env exists mcinitcmd && env exists secureboot "\
|
|
"&& esbc_validate 0x20780000; " \
|
|
"env exists mcinitcmd && " \
|
|
"fsl_mc lazyapply dpl 0x20d00000; " \
|
|
"run distro_bootcmd;run qspi_bootcmd; " \
|
|
"env exists secureboot && esbc_halt;"
|
|
|
|
/* Try to boot an on-SD kernel first, then do normal distro boot */
|
|
#define SD_BOOTCOMMAND \
|
|
"env exists mcinitcmd && env exists secureboot "\
|
|
"&& mmcinfo && mmc read $load_addr 0x3c00 0x800 " \
|
|
"&& esbc_validate $load_addr; " \
|
|
"env exists mcinitcmd && run mcinitcmd " \
|
|
"&& mmc read 0x80d00000 0x6800 0x800 " \
|
|
"&& fsl_mc lazyapply dpl 0x80d00000; " \
|
|
"run distro_bootcmd;run sd_bootcmd; " \
|
|
"env exists secureboot && esbc_halt;"
|
|
|
|
/* Try to boot an on-NOR kernel first, then do normal distro boot */
|
|
#define IFC_NOR_BOOTCOMMAND \
|
|
"env exists mcinitcmd && env exists secureboot "\
|
|
"&& esbc_validate 0x580780000; env exists mcinitcmd "\
|
|
"&& fsl_mc lazyapply dpl 0x580d00000;" \
|
|
"run distro_bootcmd;run nor_bootcmd; " \
|
|
"env exists secureboot && esbc_halt;"
|
|
#else
|
|
#undef CONFIG_BOOTCOMMAND
|
|
#ifdef CONFIG_QSPI_BOOT
|
|
/* Try to boot an on-QSPI kernel first, then do normal distro boot */
|
|
#define CONFIG_BOOTCOMMAND \
|
|
"env exists mcinitcmd && env exists secureboot "\
|
|
"&& esbc_validate 0x20780000; " \
|
|
"env exists mcinitcmd && " \
|
|
"fsl_mc lazyapply dpl 0x20d00000; " \
|
|
"run distro_bootcmd;run qspi_bootcmd; " \
|
|
"env exists secureboot && esbc_halt;"
|
|
#elif defined(CONFIG_SD_BOOT)
|
|
/* Try to boot an on-SD kernel first, then do normal distro boot */
|
|
#define CONFIG_BOOTCOMMAND \
|
|
"env exists mcinitcmd && env exists secureboot "\
|
|
"&& mmcinfo && mmc read $load_addr 0x3c00 0x800 " \
|
|
"&& esbc_validate $load_addr; " \
|
|
"env exists mcinitcmd && run mcinitcmd " \
|
|
"&& mmc read 0x88000000 0x6800 0x800 " \
|
|
"&& fsl_mc lazyapply dpl 0x88000000; " \
|
|
"run distro_bootcmd;run sd_bootcmd; " \
|
|
"env exists secureboot && esbc_halt;"
|
|
#else
|
|
/* Try to boot an on-NOR kernel first, then do normal distro boot */
|
|
#define CONFIG_BOOTCOMMAND \
|
|
"env exists mcinitcmd && env exists secureboot "\
|
|
"&& esbc_validate 0x580780000; env exists mcinitcmd "\
|
|
"&& fsl_mc lazyapply dpl 0x580d00000;" \
|
|
"run distro_bootcmd;run nor_bootcmd; " \
|
|
"env exists secureboot && esbc_halt;"
|
|
#endif
|
|
#endif
|
|
|
|
/* MAC/PHY configuration */
|
|
#ifdef CONFIG_FSL_MC_ENET
|
|
#define CONFIG_PHY_CORTINA
|
|
#define CONFIG_SYS_CORTINA_FW_IN_NOR
|
|
#ifdef CONFIG_QSPI_BOOT
|
|
#define CONFIG_CORTINA_FW_ADDR 0x20980000
|
|
#else
|
|
#define CONFIG_CORTINA_FW_ADDR 0x580980000
|
|
#endif
|
|
#define CONFIG_CORTINA_FW_LENGTH 0x40000
|
|
|
|
#define CORTINA_PHY_ADDR1 0x10
|
|
#define CORTINA_PHY_ADDR2 0x11
|
|
#define CORTINA_PHY_ADDR3 0x12
|
|
#define CORTINA_PHY_ADDR4 0x13
|
|
#define AQ_PHY_ADDR1 0x00
|
|
#define AQ_PHY_ADDR2 0x01
|
|
#define AQ_PHY_ADDR3 0x02
|
|
#define AQ_PHY_ADDR4 0x03
|
|
#define AQR405_IRQ_MASK 0x36
|
|
|
|
#define CONFIG_ETHPRIME "DPMAC1@xgmii"
|
|
#endif
|
|
|
|
#include <asm/fsl_secure_boot.h>
|
|
|
|
#endif /* __LS2_RDB_H */
|