mirrors/u-boot
0
0
Fork 0
mirror of https://github.com/u-boot/u-boot.git synced 2024-12-26 05:03:30 +08:00
Code Issues Packages Projects Releases Wiki Activity
a09fea1d28
u-boot/include/configs/M5235EVB.h
Tom Rini a09fea1d28 env: Finish migration of common ENV options 
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00

204 lines
6.2 KiB
C
Raw Blame History

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Configuation settings for the Freescale MCF5329 FireEngine board.
*
* Copyright (C) 2004-2007 Freescale Semiconductor, Inc.
* TsiChung Liew (Tsi-Chung.Liew@freescale.com)
*/
/*
* board/config.h - configuration options, board specific
*/
#ifndef _M5235EVB_H
#define _M5235EVB_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_MCFUART
#define CONFIG_SYS_UART_PORT (0)
#undef CONFIG_WATCHDOG
#define CONFIG_WATCHDOG_TIMEOUT 5000 /* timeout in milliseconds, max timeout is 6.71sec */
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_MCFFEC
#ifdef CONFIG_MCFFEC
# define CONFIG_MII_INIT 1
# define CONFIG_SYS_DISCOVER_PHY
# define CONFIG_SYS_RX_ETH_BUFFER 8
# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
# define CONFIG_SYS_FEC0_PINMUX 0
# define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE
# define MCFFEC_TOUT_LOOP 50000
/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
# ifndef CONFIG_SYS_DISCOVER_PHY
# define FECDUPLEX FULL
# define FECSPEED _100BASET
# else
# ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
# endif
# endif /* CONFIG_SYS_DISCOVER_PHY */
#endif
/* Timer */
#define CONFIG_MCFTMR
#undef CONFIG_MCFPIT
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_i2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED 80000
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET 0x00000300
#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
#define CONFIG_SYS_I2C_PINMUX_REG (gpio->par_qspi)
#define CONFIG_SYS_I2C_PINMUX_CLR ~(GPIO_PAR_FECI2C_SCL_MASK | GPIO_PAR_FECI2C_SDA_MASK)
#define CONFIG_SYS_I2C_PINMUX_SET (GPIO_PAR_FECI2C_SCL_I2CSCL | GPIO_PAR_FECI2C_SDA_I2CSDA)
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#define CONFIG_BOOTFILE "u-boot.bin"
#ifdef CONFIG_MCFFEC
# define CONFIG_IPADDR 192.162.1.2
# define CONFIG_NETMASK 255.255.255.0
# define CONFIG_SERVERIP 192.162.1.1
# define CONFIG_GATEWAYIP 192.162.1.1
#endif /* FEC_ENET */
#define CONFIG_HOSTNAME "M5235EVB"
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"loadaddr=10000\0" \
"u-boot=u-boot.bin\0" \
"load=tftp ${loadaddr) ${u-boot}\0" \
"upd=run load; run prog\0" \
"prog=prot off ffe00000 ffe3ffff;" \
"era ffe00000 ffe3ffff;" \
"cp.b ${loadaddr} ffe00000 ${filesize};"\
"save\0" \
""
#define CONFIG_PRAM 512 /* 512 KB */
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE+0x20000)
#define CONFIG_SYS_CLK 75000000
#define CONFIG_SYS_CPU_CLK CONFIG_SYS_CLK * 2
#define CONFIG_SYS_MBAR 0x40000000
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
*/
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000
#define CONFIG_SYS_INIT_RAM_SIZE 0x10000 /* Size of used area in internal SRAM */
#define CONFIG_SYS_INIT_RAM_CTRL 0x21
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE - 0x10)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
#define CONFIG_SYS_SDRAM_BASE 0x00000000
#define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */
#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE + 0x400
#define CONFIG_SYS_MEMTEST_END ((CONFIG_SYS_SDRAM_SIZE - 3) << 20)
#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024
#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization ??
*/
/* Initial Memory map for Linux */
#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
#define CONFIG_SYS_BOOTM_LEN (CONFIG_SYS_SDRAM_SIZE << 20)
/*-----------------------------------------------------------------------
* FLASH organization
*/
#ifdef CONFIG_SYS_FLASH_CFI
# define CONFIG_SYS_FLASH_SIZE 0x800000 /* Max size that the board might have */
#ifdef NORFLASH_PS32BIT
# define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_32BIT
#else
# define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
#endif
# define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
# define CONFIG_SYS_MAX_FLASH_SECT 137 /* max number of sectors on one chip */
#endif
#define CONFIG_SYS_FLASH_BASE (CONFIG_SYS_CS0_BASE)
/* Configuration for environment
* Environment is embedded in u-boot in the second sector of the flash
*/
#define LDS_BOARD_TEXT \
. = DEFINED(env_offset) ? env_offset : .; \
env/embedded.o(.text);
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CONFIG_SYS_CACHELINE_SIZE 16
#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
CONFIG_SYS_INIT_RAM_SIZE - 8)
#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
CONFIG_SYS_INIT_RAM_SIZE - 4)
#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV)
#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \
CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
CF_ACR_EN | CF_ACR_SM_ALL)
#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_DISD | \
CF_CACR_CEIB | CF_CACR_DCM | \
CF_CACR_EUSP)
/*-----------------------------------------------------------------------
* Chipselect bank definitions
*/
/*
* CS0 - NOR Flash 1, 2, 4, or 8MB
* CS1 - Available
* CS2 - Available
* CS3 - Available
* CS4 - Available
* CS5 - Available
* CS6 - Available
* CS7 - Available
*/
#ifdef NORFLASH_PS32BIT
# define CONFIG_SYS_CS0_BASE 0xFFC00000
# define CONFIG_SYS_CS0_MASK 0x003f0001
# define CONFIG_SYS_CS0_CTRL 0x00001D00
#else
# define CONFIG_SYS_CS0_BASE 0xFFE00000
# define CONFIG_SYS_CS0_MASK 0x001f0001
# define CONFIG_SYS_CS0_CTRL 0x00001D80
#endif
#endif /* _M5329EVB_H */
Reference in New Issue View Git Blame Copy Permalink