u-boot/doc/board/xilinx/zynqmp-r5.rst
Michal Simek e6ff998cb0 global: Use proper project name U-Boot (next2)
Use proper project name in README, rst and comment.
Done in connection to commit bb922ca3eb ("global: Use proper project name
U-Boot (next)").

Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexander Graf <graf@csgraf.de> (ppce500)
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/536af05e7061982f15b668e87f941cdabfa25392.1694157084.git.michal.simek@amd.com
2023-09-21 13:20:11 +02:00

138 lines
3.5 KiB
ReStructuredText

.. SPDX-License-Identifier: GPL-2.0
.. (C) Copyright 2020 Xilinx, Inc.
ZYNQMP-R5
=========
About this
----------
This document describes the information about Xilinx Zynq UltraScale+ MPSOC
U-Boot Cortex R5 support.
ZynqMP R5 boards
----------------
* zynqmp-r5 - U-Boot running on RPU Cortex-R5
Building
--------
configure and build armv7 toolchain::
$ make xilinx_zynqmp_r5_defconfig
$ make
Notes
^^^^^
Output fragment is U-Boot.
Loading
-------
ZynqMP R5 U-Boot was created for supporting loading OS on RPU. There are two
ways how to start U-Boot on R5.
Bootgen
^^^^^^^
The first way is to use Xilinx FSBL (First stage
bootloader) to load U-Boot and start it. The following bif can be used for boot
image generation via Xilinx bootgen utility::
the_ROM_image:
{
[bootloader,destination_cpu=r5-0] fsbl_rpu.elf
[destination_cpu=r5-0]u-boot.elf
}
Bootgen command for building boot.bin::
bootgen -image <bif>.bif -r -w -o i boot.bin
U-Boot cpu command
^^^^^^^^^^^^^^^^^^
The second way to load U-Boot to Cortex R5 is from U-Boot running on A53 as is
visible from the following log::
U-Boot SPL 2020.10-rc4-00090-g801b3d5c5757 (Sep 15 2020 - 14:07:24 +0200)
PMUFW: v1.1
Loading new PMUFW cfg obj (2024 bytes)
EL Level: EL3
Multiboot: 0
Trying to boot from MMC2
spl: could not initialize mmc. error: -19
Trying to boot from MMC1
spl_load_image_fat_os: error reading image u-boot.bin, err - -2
NOTICE: ATF running on XCZU7EG/EV/silicon v4/RTL5.1 at 0xfffea000
NOTICE: BL31: v2.2(release):v2.2-614-ged9dc512fb9c
NOTICE: BL31: Built : 09:32:09, Mar 13 2020
U-Boot 2020.10-rc4-00090-g801b3d5c5757 (Sep 15 2020 - 14:07:24 +0200)
Model: ZynqMP ZCU104 RevC
Board: Xilinx ZynqMP
DRAM: 2 GiB
PMUFW: v1.1
EL Level: EL2
Chip ID: zu7e
WDT: Started with servicing (60s timeout)
NAND: 0 MiB
MMC: mmc@ff170000: 0
Loading Environment from FAT... *** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Bootmode: LVL_SHFT_SD_MODE1
Reset reason: SOFT
Net:
ZYNQ GEM: ff0e0000, mdio bus ff0e0000, phyaddr 12, interface rgmii-id
eth0: ethernet@ff0e0000
Hit any key to stop autoboot: 0
ZynqMP> setenv autoload no
ZynqMP> dhcp
BOOTP broadcast 1
DHCP client bound to address 192.168.0.167 (8 ms)
ZynqMP> tftpboot 20000000 192.168.0.105:u-boot-r5-2.elf
Using ethernet@ff0e0000 device
TFTP from server 192.168.0.105; our IP address is 192.168.0.167
Filename 'u-boot-r5-2.elf'.
Load address: 0x20000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
################
376 KiB/s
done
Bytes transferred = 2075464 (1fab48 hex)
ZynqMP> setenv autostart no
ZynqMP> bootelf -p 20000000
ZynqMP> cpu 4 release 10000000 lockstep
Using TCM jump trampoline for address 0x10000000
R5 lockstep mode
ZynqMP>
Then on second uart you can see U-Boot up and running on R5::
U-Boot 2020.10-rc4-00071-g7045622cc9ba (Sep 16 2020 - 13:38:53 +0200)
Model: Xilinx ZynqMP R5
DRAM: 512 MiB
MMC:
In: serial@ff010000
Out: serial@ff010000
Err: serial@ff010000
Net: No ethernet found.
ZynqMP r5>
Please make sure MIO pins for uart are properly configured to see output.