mirror of
https://github.com/u-boot/u-boot.git
synced 2024-12-27 05:33:27 +08:00
2fe88d4522
This converts the following to Kconfig: CONFIG_FLASH_CFI_DRIVER CONFIG_SYS_FLASH_USE_BUFFER_WRITE CONFIG_FLASH_CFI_MTD CONFIG_SYS_FLASH_PROTECTION CONFIG_SYS_FLASH_CFI Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Re-migrate] Signed-off-by: Tom Rini <trini@konsulko.com>
501 lines
16 KiB
C
501 lines
16 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* Copyright 2010 Extreme Engineering Solutions, Inc.
|
|
* Copyright 2007-2008 Freescale Semiconductor, Inc.
|
|
*/
|
|
|
|
/*
|
|
* xpedite550x board configuration file
|
|
*/
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
*/
|
|
#define CONFIG_SYS_BOARD_NAME "XPedite5500"
|
|
#define CONFIG_SYS_FORM_PMC_XMC 1
|
|
#define CONFIG_PRPMC_PCI_ALIAS "pci0" /* Processor PMC interface on pci0 */
|
|
|
|
#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
|
|
#define CONFIG_PCIE1 1 /* PCIE controller 1 (PEX8112 or XMC) */
|
|
#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
|
|
#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
|
|
#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
|
|
#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */
|
|
|
|
/*
|
|
* Multicore config
|
|
*/
|
|
#define CONFIG_BPTR_VIRT_ADDR 0xee000000 /* virt boot page address */
|
|
#define CONFIG_MPC8xxx_DISABLE_BPTR /* Don't leave BPTR enabled */
|
|
|
|
/*
|
|
* DDR config
|
|
*/
|
|
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
|
|
#define CONFIG_DDR_SPD
|
|
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
|
|
#define SPD_EEPROM_ADDRESS 0x54
|
|
#define SPD_EEPROM_OFFSET 0x200 /* OFFSET of SPD in EEPROM */
|
|
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
|
|
#define CONFIG_CHIP_SELECTS_PER_CTRL 2
|
|
#define CONFIG_DDR_ECC
|
|
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
|
|
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
|
|
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
|
|
#define CONFIG_VERY_BIG_RAM
|
|
|
|
#ifndef __ASSEMBLY__
|
|
extern unsigned long get_board_sys_clk(unsigned long dummy);
|
|
extern unsigned long get_board_ddr_clk(unsigned long dummy);
|
|
#endif
|
|
|
|
#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */
|
|
#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) /* ddrclk for MPC85xx */
|
|
|
|
/*
|
|
* These can be toggled for performance analysis, otherwise use default.
|
|
*/
|
|
#define CONFIG_L2_CACHE /* toggle L2 cache */
|
|
#define CONFIG_BTB /* toggle branch predition */
|
|
#define CONFIG_ENABLE_36BIT_PHYS 1
|
|
|
|
#define CONFIG_SYS_CCSRBAR 0xef000000
|
|
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
|
|
|
|
/*
|
|
* Diagnostics
|
|
*/
|
|
#define CONFIG_SYS_MEMTEST_START 0x10000000
|
|
#define CONFIG_SYS_MEMTEST_END 0x20000000
|
|
#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
|
|
CONFIG_SYS_POST_I2C)
|
|
#define I2C_ADDR_LIST {CONFIG_SYS_I2C_EEPROM_ADDR, \
|
|
CONFIG_SYS_I2C_LM75_ADDR, \
|
|
CONFIG_SYS_I2C_LM90_ADDR, \
|
|
CONFIG_SYS_I2C_PCA953X_ADDR0, \
|
|
CONFIG_SYS_I2C_PCA953X_ADDR2, \
|
|
CONFIG_SYS_I2C_PCA953X_ADDR3, \
|
|
CONFIG_SYS_I2C_RTC_ADDR}
|
|
|
|
/*
|
|
* Memory map
|
|
* 0x0000_0000 0x7fff_ffff DDR 2G Cacheable
|
|
* 0x8000_0000 0xbfff_ffff PCIe1 Mem 1G non-cacheable
|
|
* 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable
|
|
* 0xe800_0000 0xe87f_ffff PCIe1 IO 8M non-cacheable
|
|
* 0xee00_0000 0xee00_ffff Boot page translation 4K non-cacheable
|
|
* 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable
|
|
* 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable
|
|
* 0xf000_0000 0xf7ff_ffff NOR Flash 2 128M non-cacheable
|
|
* 0xf800_0000 0xffff_ffff NOR Flash 1 128M non-cacheable
|
|
*/
|
|
|
|
#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_3)
|
|
|
|
/*
|
|
* NAND flash configuration
|
|
*/
|
|
#define CONFIG_SYS_NAND_BASE 0xef800000
|
|
#define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */
|
|
#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE, \
|
|
CONFIG_SYS_NAND_BASE2}
|
|
#define CONFIG_SYS_MAX_NAND_DEVICE 2
|
|
#define CONFIG_NAND_FSL_ELBC
|
|
|
|
/*
|
|
* NOR flash configuration
|
|
*/
|
|
#define CONFIG_SYS_FLASH_BASE 0xf8000000
|
|
#define CONFIG_SYS_FLASH_BASE2 0xf0000000
|
|
#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
|
|
#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \
|
|
{0xf7f40000, 0xc0000} }
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
|
|
|
|
/*
|
|
* Chip select configuration
|
|
*/
|
|
/* NOR Flash 0 on CS0 */
|
|
#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \
|
|
BR_PS_16 | \
|
|
BR_V)
|
|
#define CONFIG_SYS_OR0_PRELIM (OR_AM_128MB | \
|
|
OR_GPCM_CSNT | \
|
|
OR_GPCM_XACS | \
|
|
OR_GPCM_ACS_DIV2 | \
|
|
OR_GPCM_SCY_8 | \
|
|
OR_GPCM_TRLX | \
|
|
OR_GPCM_EHTR | \
|
|
OR_GPCM_EAD)
|
|
|
|
/* NOR Flash 1 on CS1 */
|
|
#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 | \
|
|
BR_PS_16 | \
|
|
BR_V)
|
|
#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
|
|
|
|
/* NAND flash on CS2 */
|
|
#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE | \
|
|
(2<<BR_DECC_SHIFT) | \
|
|
BR_PS_8 | \
|
|
BR_MS_FCM | \
|
|
BR_V)
|
|
|
|
/* NAND flash on CS2 */
|
|
#define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB | \
|
|
OR_FCM_PGS | \
|
|
OR_FCM_CSCT | \
|
|
OR_FCM_CST | \
|
|
OR_FCM_CHT | \
|
|
OR_FCM_SCY_1 | \
|
|
OR_FCM_TRLX | \
|
|
OR_FCM_EHTR)
|
|
|
|
/* NAND flash on CS3 */
|
|
#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 | \
|
|
(2<<BR_DECC_SHIFT) | \
|
|
BR_PS_8 | \
|
|
BR_MS_FCM | \
|
|
BR_V)
|
|
#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM
|
|
|
|
/*
|
|
* Use L1 as initial stack
|
|
*/
|
|
#define CONFIG_SYS_INIT_RAM_LOCK 1
|
|
#define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000
|
|
#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
|
|
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
|
|
#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */
|
|
#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
|
|
|
|
/*
|
|
* Serial Port
|
|
*/
|
|
#define CONFIG_SYS_NS16550_SERIAL
|
|
#define CONFIG_SYS_NS16550_REG_SIZE 1
|
|
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
|
|
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
|
|
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
|
|
#define CONFIG_SYS_BAUDRATE_TABLE \
|
|
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
|
|
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
|
|
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
|
|
|
|
|
|
/*
|
|
* I2C
|
|
*/
|
|
#define CONFIG_SYS_I2C
|
|
#define CONFIG_SYS_I2C_FSL
|
|
#define CONFIG_SYS_FSL_I2C_SPEED 400000
|
|
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
|
|
#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
|
|
#define CONFIG_SYS_FSL_I2C2_SPEED 400000
|
|
#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
|
|
#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
|
|
|
|
/* I2C DS7505 temperature sensor */
|
|
#define CONFIG_SYS_I2C_LM75_ADDR 0x48
|
|
|
|
/* I2C ADT7461 temperature sensor */
|
|
#define CONFIG_SYS_I2C_LM90_ADDR 0x4C
|
|
|
|
/* I2C EEPROM - AT24C128B */
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */
|
|
|
|
/* I2C RTC */
|
|
#define CONFIG_RTC_M41T11 1
|
|
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
|
|
#define CONFIG_SYS_M41T11_BASE_YEAR 2000
|
|
|
|
/* GPIO */
|
|
#define CONFIG_PCA953X
|
|
#define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18
|
|
#define CONFIG_SYS_I2C_PCA953X_ADDR1 0x1c
|
|
#define CONFIG_SYS_I2C_PCA953X_ADDR2 0x1e
|
|
#define CONFIG_SYS_I2C_PCA953X_ADDR3 0x1f
|
|
#define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0
|
|
|
|
/*
|
|
* GPIO pin definitions, PU = pulled high, PD = pulled low
|
|
*/
|
|
/* PCA9557 @ 0x18*/
|
|
#define CONFIG_SYS_PCA953X_C0_SER0_EN 0x01 /* PU; UART0 enable (1: enabled) */
|
|
#define CONFIG_SYS_PCA953X_C0_SER0_MODE 0x02 /* PU; UART0 serial mode select (1: RS-485, 0: RS-232) */
|
|
#define CONFIG_SYS_PCA953X_C0_SER1_EN 0x04 /* PU; UART1 enable (1: enabled) */
|
|
#define CONFIG_SYS_PCA953X_C0_SER1_MODE 0x08 /* PU; UART1 serial mode select (1: RS-485, 0: RS-232) */
|
|
#define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS 0x10 /* PU; Boot flash CS select */
|
|
#define CONFIG_SYS_PCA953X_NVM_WP 0x20 /* PU; Write protection (0: disabled, 1: enabled) */
|
|
|
|
/* PCA9557 @ 0x1e*/
|
|
#define CONFIG_SYS_PCA953X_XMC_GA0 0x01 /* PU; */
|
|
#define CONFIG_SYS_PCA953X_XMC_GA1 0x02 /* PU; */
|
|
#define CONFIG_SYS_PCA953X_XMC_GA2 0x04 /* PU; */
|
|
#define CONFIG_SYS_PCA953X_XMC_WAKE 0x10 /* PU; */
|
|
#define CONFIG_SYS_PCA953X_XMC_BIST 0x20 /* Enable XMC BIST */
|
|
#define CONFIG_SYS_PCA953X_PMC_EREADY 0x40 /* PU; PMC PCI eready */
|
|
#define CONFIG_SYS_PCA953X_PMC_MONARCH 0x80 /* PMC monarch mode enable */
|
|
|
|
/* PCA9557 @ 0x1f */
|
|
#define CONFIG_SYS_PCA953X_MC_GPIO0 0x01 /* PU; */
|
|
#define CONFIG_SYS_PCA953X_MC_GPIO1 0x02 /* PU; */
|
|
#define CONFIG_SYS_PCA953X_MC_GPIO2 0x04 /* PU; */
|
|
#define CONFIG_SYS_PCA953X_MC_GPIO3 0x08 /* PU; */
|
|
#define CONFIG_SYS_PCA953X_MC_GPIO4 0x10 /* PU; */
|
|
#define CONFIG_SYS_PCA953X_MC_GPIO5 0x20 /* PU; */
|
|
#define CONFIG_SYS_PCA953X_MC_GPIO6 0x40 /* PU; */
|
|
#define CONFIG_SYS_PCA953X_MC_GPIO7 0x80 /* PU; */
|
|
|
|
/*
|
|
* General PCI
|
|
* Memory space is mapped 1-1, but I/O space must start from 0.
|
|
*/
|
|
|
|
/* controller 1 - PEX8112 or XMC, depending on build option */
|
|
#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
|
|
#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS
|
|
#define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */
|
|
#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
|
|
#define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000
|
|
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */
|
|
|
|
/*
|
|
* Networking options
|
|
*/
|
|
#define CONFIG_TSEC_TBI
|
|
#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
|
|
#define CONFIG_ETHPRIME "eTSEC2"
|
|
|
|
/*
|
|
* In-band SGMII auto-negotiation between TBI and BCM5482S PHY fails, force
|
|
* 1000mbps SGMII link
|
|
*/
|
|
#define CONFIG_TSEC_TBICR_SETTINGS ( \
|
|
TBICR_PHY_RESET \
|
|
| TBICR_FULL_DUPLEX \
|
|
| TBICR_SPEED1_SET \
|
|
)
|
|
|
|
#define CONFIG_TSEC1 1
|
|
#define CONFIG_TSEC1_NAME "eTSEC1"
|
|
#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
|
|
#define TSEC1_PHY_ADDR 1
|
|
#define TSEC1_PHYIDX 0
|
|
#define CONFIG_HAS_ETH0
|
|
|
|
#define CONFIG_TSEC2 1
|
|
#define CONFIG_TSEC2_NAME "eTSEC2"
|
|
#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
|
|
#define TSEC2_PHY_ADDR 2
|
|
#define TSEC2_PHYIDX 0
|
|
#define CONFIG_HAS_ETH1
|
|
|
|
#define CONFIG_TSEC3 1
|
|
#define CONFIG_TSEC3_NAME "eTSEC3"
|
|
#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
|
|
#define TSEC3_PHY_ADDR 3
|
|
#define TSEC3_PHYIDX 0
|
|
#define CONFIG_HAS_ETH2
|
|
|
|
/*
|
|
* USB
|
|
*/
|
|
#define CONFIG_USB_EHCI_FSL
|
|
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
|
|
#define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */
|
|
#define CONFIG_PREBOOT /* enable preboot variable */
|
|
#define CONFIG_INTEGRITY /* support booting INTEGRITY OS */
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 16 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
|
|
#define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */
|
|
|
|
/*
|
|
* Environment Configuration
|
|
*/
|
|
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */
|
|
#define CONFIG_ENV_SIZE 0x8000
|
|
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024))
|
|
|
|
/*
|
|
* Flash memory map:
|
|
* fff80000 - ffffffff Pri U-Boot (512 KB)
|
|
* fff40000 - fff7ffff Pri U-Boot Environment (256 KB)
|
|
* fff00000 - fff3ffff Pri FDT (256KB)
|
|
* fef00000 - ffefffff Pri OS image (16MB)
|
|
* f8000000 - feefffff Pri OS Use/Filesystem (111MB)
|
|
*
|
|
* f7f80000 - f7ffffff Sec U-Boot (512 KB)
|
|
* f7f40000 - f7f7ffff Sec U-Boot Environment (256 KB)
|
|
* f7f00000 - f7f3ffff Sec FDT (256KB)
|
|
* f6f00000 - f7efffff Sec OS image (16MB)
|
|
* f0000000 - f6efffff Sec OS Use/Filesystem (111MB)
|
|
*/
|
|
#define CONFIG_UBOOT1_ENV_ADDR __stringify(0xfff80000)
|
|
#define CONFIG_UBOOT2_ENV_ADDR __stringify(0xf7f80000)
|
|
#define CONFIG_FDT1_ENV_ADDR __stringify(0xfff00000)
|
|
#define CONFIG_FDT2_ENV_ADDR __stringify(0xf7f00000)
|
|
#define CONFIG_OS1_ENV_ADDR __stringify(0xfef00000)
|
|
#define CONFIG_OS2_ENV_ADDR __stringify(0xf6f00000)
|
|
|
|
#define CONFIG_PROG_UBOOT1 \
|
|
"$download_cmd $loadaddr $ubootfile; " \
|
|
"if test $? -eq 0; then " \
|
|
"protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
|
|
"erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
|
|
"cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \
|
|
"protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
|
|
"cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \
|
|
"if test $? -ne 0; then " \
|
|
"echo PROGRAM FAILED; " \
|
|
"else; " \
|
|
"echo PROGRAM SUCCEEDED; " \
|
|
"fi; " \
|
|
"else; " \
|
|
"echo DOWNLOAD FAILED; " \
|
|
"fi;"
|
|
|
|
#define CONFIG_PROG_UBOOT2 \
|
|
"$download_cmd $loadaddr $ubootfile; " \
|
|
"if test $? -eq 0; then " \
|
|
"protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
|
|
"erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
|
|
"cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \
|
|
"protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
|
|
"cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \
|
|
"if test $? -ne 0; then " \
|
|
"echo PROGRAM FAILED; " \
|
|
"else; " \
|
|
"echo PROGRAM SUCCEEDED; " \
|
|
"fi; " \
|
|
"else; " \
|
|
"echo DOWNLOAD FAILED; " \
|
|
"fi;"
|
|
|
|
#define CONFIG_BOOT_OS_NET \
|
|
"$download_cmd $osaddr $osfile; " \
|
|
"if test $? -eq 0; then " \
|
|
"if test -n $fdtaddr; then " \
|
|
"$download_cmd $fdtaddr $fdtfile; " \
|
|
"if test $? -eq 0; then " \
|
|
"bootm $osaddr - $fdtaddr; " \
|
|
"else; " \
|
|
"echo FDT DOWNLOAD FAILED; " \
|
|
"fi; " \
|
|
"else; " \
|
|
"bootm $osaddr; " \
|
|
"fi; " \
|
|
"else; " \
|
|
"echo OS DOWNLOAD FAILED; " \
|
|
"fi;"
|
|
|
|
#define CONFIG_PROG_OS1 \
|
|
"$download_cmd $osaddr $osfile; " \
|
|
"if test $? -eq 0; then " \
|
|
"erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \
|
|
"cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \
|
|
"cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \
|
|
"if test $? -ne 0; then " \
|
|
"echo OS PROGRAM FAILED; " \
|
|
"else; " \
|
|
"echo OS PROGRAM SUCCEEDED; " \
|
|
"fi; " \
|
|
"else; " \
|
|
"echo OS DOWNLOAD FAILED; " \
|
|
"fi;"
|
|
|
|
#define CONFIG_PROG_OS2 \
|
|
"$download_cmd $osaddr $osfile; " \
|
|
"if test $? -eq 0; then " \
|
|
"erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \
|
|
"cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \
|
|
"cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \
|
|
"if test $? -ne 0; then " \
|
|
"echo OS PROGRAM FAILED; " \
|
|
"else; " \
|
|
"echo OS PROGRAM SUCCEEDED; " \
|
|
"fi; " \
|
|
"else; " \
|
|
"echo OS DOWNLOAD FAILED; " \
|
|
"fi;"
|
|
|
|
#define CONFIG_PROG_FDT1 \
|
|
"$download_cmd $fdtaddr $fdtfile; " \
|
|
"if test $? -eq 0; then " \
|
|
"erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \
|
|
"cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \
|
|
"cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \
|
|
"if test $? -ne 0; then " \
|
|
"echo FDT PROGRAM FAILED; " \
|
|
"else; " \
|
|
"echo FDT PROGRAM SUCCEEDED; " \
|
|
"fi; " \
|
|
"else; " \
|
|
"echo FDT DOWNLOAD FAILED; " \
|
|
"fi;"
|
|
|
|
#define CONFIG_PROG_FDT2 \
|
|
"$download_cmd $fdtaddr $fdtfile; " \
|
|
"if test $? -eq 0; then " \
|
|
"erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \
|
|
"cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \
|
|
"cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \
|
|
"if test $? -ne 0; then " \
|
|
"echo FDT PROGRAM FAILED; " \
|
|
"else; " \
|
|
"echo FDT PROGRAM SUCCEEDED; " \
|
|
"fi; " \
|
|
"else; " \
|
|
"echo FDT DOWNLOAD FAILED; " \
|
|
"fi;"
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"autoload=yes\0" \
|
|
"download_cmd=tftp\0" \
|
|
"console_args=console=ttyS0,115200\0" \
|
|
"root_args=root=/dev/nfs rw\0" \
|
|
"misc_args=ip=on\0" \
|
|
"set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
|
|
"bootfile=/home/user/file\0" \
|
|
"osfile=/home/user/board.uImage\0" \
|
|
"fdtfile=/home/user/board.dtb\0" \
|
|
"ubootfile=/home/user/u-boot.bin\0" \
|
|
"fdtaddr=0x1e00000\0" \
|
|
"osaddr=0x1000000\0" \
|
|
"loadaddr=0x1000000\0" \
|
|
"prog_uboot1="CONFIG_PROG_UBOOT1"\0" \
|
|
"prog_uboot2="CONFIG_PROG_UBOOT2"\0" \
|
|
"prog_os1="CONFIG_PROG_OS1"\0" \
|
|
"prog_os2="CONFIG_PROG_OS2"\0" \
|
|
"prog_fdt1="CONFIG_PROG_FDT1"\0" \
|
|
"prog_fdt2="CONFIG_PROG_FDT2"\0" \
|
|
"bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \
|
|
"bootcmd_flash1=run set_bootargs; " \
|
|
"bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
|
|
"bootcmd_flash2=run set_bootargs; " \
|
|
"bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
|
|
"bootcmd=run bootcmd_flash1\0"
|
|
#endif /* __CONFIG_H */
|