u-boot/include/configs/ls1012ardb.h
Rajesh Bhagat 1f6180dff9 armv8: ls1012ardb: Add TFABOOT support
TFABOOT support includes:
 - ls1012ardb_tfa_defconfig to be loaded by trusted firmware
 - environment address and size changes for TFABOOT
 - define BOOTCOMMAND for TFABOOT
 - enable PFE validation for secure boot

Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06 14:37:19 -08:00

127 lines
3.5 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2016 Freescale Semiconductor, Inc.
*/
#ifndef __LS1012ARDB_H__
#define __LS1012ARDB_H__
#include "ls1012a_common.h"
/* DDR */
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
#define CONFIG_CHIP_SELECTS_PER_CTRL 1
#define CONFIG_SYS_SDRAM_SIZE 0x40000000
#define CONFIG_CMD_MEMINFO
#define CONFIG_SYS_MEMTEST_START 0x80000000
#define CONFIG_SYS_MEMTEST_END 0x9fffffff
/*
* I2C IO expander
*/
#define I2C_MUX_IO_ADDR 0x24
#define I2C_MUX_IO2_ADDR 0x25
#define I2C_MUX_IO_0 0
#define I2C_MUX_IO_1 1
#define SW_BOOT_MASK 0x03
#define SW_BOOT_EMU 0x02
#define SW_BOOT_BANK1 0x00
#define SW_BOOT_BANK2 0x01
#define SW_REV_MASK 0xF8
#define SW_REV_A 0xF8
#define SW_REV_B 0xF0
#define SW_REV_C 0xE8
#define SW_REV_C1 0xE0
#define SW_REV_C2 0xD8
#define SW_REV_D 0xD0
#define SW_REV_E 0xC8
#define __PHY_MASK 0xF9
#define __PHY_ETH2_MASK 0xFB
#define __PHY_ETH1_MASK 0xFD
/* MMC */
#ifdef CONFIG_MMC
#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
#endif
#define CONFIG_PCIE1 /* PCIE controller 1 */
#define CONFIG_PCI_SCAN_SHOW
#define CONFIG_CMD_MEMINFO
#define CONFIG_SYS_MEMTEST_START 0x80000000
#define CONFIG_SYS_MEMTEST_END 0x9fffffff
#undef CONFIG_EXTRA_ENV_SETTINGS
#define CONFIG_EXTRA_ENV_SETTINGS \
"verify=no\0" \
"fdt_high=0xffffffffffffffff\0" \
"initrd_high=0xffffffffffffffff\0" \
"fdt_addr=0x00f00000\0" \
"kernel_addr=0x01000000\0" \
"kernelheader_addr=0x800000\0" \
"scriptaddr=0x80000000\0" \
"scripthdraddr=0x80080000\0" \
"fdtheader_addr_r=0x80100000\0" \
"kernelheader_addr_r=0x80200000\0" \
"kernel_addr_r=0x81000000\0" \
"fdt_addr_r=0x90000000\0" \
"load_addr=0xa0000000\0" \
"kernel_size=0x2800000\0" \
"kernelheader_size=0x40000\0" \
"console=ttyS0,115200\0" \
BOOTENV \
"boot_scripts=ls1012ardb_boot.scr\0" \
"boot_script_hdr=hdr_ls1012ardb_bs.out\0" \
"scan_dev_for_boot_part=" \
"part list ${devtype} ${devnum} devplist; " \
"env exists devplist || setenv devplist 1; " \
"for distro_bootpart in ${devplist}; do " \
"if fstype ${devtype} " \
"${devnum}:${distro_bootpart} " \
"bootfstype; then " \
"run scan_dev_for_boot; " \
"fi; " \
"done\0" \
"scan_dev_for_boot=" \
"echo Scanning ${devtype} " \
"${devnum}:${distro_bootpart}...; " \
"for prefix in ${boot_prefixes}; do " \
"run scan_dev_for_scripts; " \
"done;" \
"\0" \
"boot_a_script=" \
"load ${devtype} ${devnum}:${distro_bootpart} " \
"${scriptaddr} ${prefix}${script}; " \
"env exists secureboot && load ${devtype} " \
"${devnum}:${distro_bootpart} " \
"${scripthdraddr} ${prefix}${boot_script_hdr} " \
"&& esbc_validate ${scripthdraddr};" \
"source ${scriptaddr}\0" \
"installer=load mmc 0:2 $load_addr " \
"/flex_installer_arm64.itb; " \
"bootm $load_addr#$board\0" \
"qspi_bootcmd=echo Trying load from qspi..;" \
"sf probe && sf read $load_addr " \
"$kernel_addr $kernel_size; env exists secureboot " \
"&& sf read $kernelheader_addr_r $kernelheader_addr " \
"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
"bootm $load_addr#$board\0"
#undef CONFIG_BOOTCOMMAND
#ifdef CONFIG_TFABOOT
#undef QSPI_NOR_BOOTCOMMAND
#define QSPI_NOR_BOOTCOMMAND "pfe stop; run distro_bootcmd; run qspi_bootcmd; "\
"env exists secureboot && esbc_halt;"
#else
#define CONFIG_BOOTCOMMAND "pfe stop; run distro_bootcmd; run qspi_bootcmd; "\
"env exists secureboot && esbc_halt;"
#endif
#include <asm/fsl_secure_boot.h>
#endif /* __LS1012ARDB_H__ */