u-boot/configs/sama5d2_xplained_spiflash_defconfig
Anatolij Gustschin 2cc393f32f video: make BPP and ANSI configs optional
Many boards do not use all selected framebuffer depth
configurations, for such boards there is some unused
code in video and console uclass routines. Make depth
specific code optional to avoid dead code and slightly
reduce binary size. Also make ANSI code optional for
the same reason. When i.e. using only VIDEO_BPP16 the
code size shrinks (below values when using gcc-7.3.0):

  $ ./tools/buildman/buildman -b video-wip -sS wandboard
  ...
  01: Merge git://git.denx.de/u-boot-sh
  02: video: add guards around 16bpp/32bbp code
  03: video: make BPP and ANSI configs optional
         arm: (for 1/1 boards) all -776.0 bss -8.0 text -768.0

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Eugen Hristev <eugen.hristev@microchip.com>
Tested-by: Patrice Chotard <patrice.chotard@st.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
2019-12-06 16:38:51 +01:00

105 lines
2.4 KiB
Plaintext

CONFIG_ARM=y
CONFIG_ARCH_CPU_INIT=y
CONFIG_ARCH_AT91=y
CONFIG_SYS_TEXT_BASE=0x26f00000
CONFIG_TARGET_SAMA5D2_XPLAINED=y
CONFIG_SPL_GPIO_SUPPORT=y
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_SPL_SERIAL_SUPPORT=y
CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
CONFIG_ENV_SIZE=0x2000
CONFIG_ENV_OFFSET=0x6000
CONFIG_NR_DRAM_BANKS=1
CONFIG_SPL=y
CONFIG_DEBUG_UART_BOARD_INIT=y
CONFIG_DEBUG_UART_BASE=0xf8020000
CONFIG_DEBUG_UART_CLOCK=83000000
CONFIG_ENV_SECT_SIZE=0x1000
CONFIG_SPL_SPI_FLASH_SUPPORT=y
CONFIG_SPL_SPI_SUPPORT=y
CONFIG_DEBUG_UART=y
CONFIG_SPL_TEXT_BASE=0x200000
CONFIG_ENV_VARS_UBOOT_CONFIG=y
CONFIG_FIT=y
CONFIG_SPI_BOOT=y
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 earlyprintk root=/dev/mmcblk0p1 rw rootwait"
CONFIG_MISC_INIT_R=y
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_SPL_SPI_LOAD=y
CONFIG_SYS_SPI_U_BOOT_OFFS=0x10000
CONFIG_HUSH_PARSER=y
CONFIG_CMD_BOOTZ=y
# CONFIG_CMD_FLASH is not set
CONFIG_CMD_I2C=y
# CONFIG_CMD_LOADS is not set
CONFIG_CMD_MMC=y
CONFIG_CMD_USB=y
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_FAT=y
CONFIG_OF_CONTROL=y
CONFIG_SPL_OF_CONTROL=y
CONFIG_DEFAULT_DEVICE_TREE="at91-sama5d2_xplained"
CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-parent dmas dma-names"
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_DM=y
CONFIG_SPL_DM=y
CONFIG_SPL_DM_SEQ_ALIAS=y
CONFIG_CLK=y
CONFIG_SPL_CLK=y
CONFIG_CLK_AT91=y
CONFIG_AT91_UTMI=y
CONFIG_AT91_H32MX=y
CONFIG_AT91_GENERIC_CLK=y
CONFIG_DM_GPIO=y
CONFIG_ATMEL_PIO4=y
CONFIG_DM_I2C=y
CONFIG_SYS_I2C_AT91=y
CONFIG_I2C_EEPROM=y
CONFIG_DM_MMC=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ATMEL=y
CONFIG_MTD=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SF_DEFAULT_SPEED=30000000
CONFIG_SPI_FLASH_ATMEL=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_SPI_FLASH_SST=y
CONFIG_DM_ETH=y
CONFIG_MACB=y
CONFIG_PINCTRL=y
CONFIG_SPL_PINCTRL=y
CONFIG_PINCTRL_AT91PIO4=y
CONFIG_DM_SERIAL=y
CONFIG_DEBUG_UART_ATMEL=y
CONFIG_DEBUG_UART_ANNOUNCE=y
CONFIG_ATMEL_USART=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
CONFIG_ATMEL_QSPI=y
CONFIG_TIMER=y
CONFIG_SPL_TIMER=y
CONFIG_ATMEL_PIT_TIMER=y
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_USB_GADGET_ATMEL_USBA=y
CONFIG_DM_VIDEO=y
CONFIG_VIDEO_BPP16=y
CONFIG_ATMEL_HLCD=y
CONFIG_W1=y
CONFIG_W1_GPIO=y
CONFIG_W1_EEPROM=y
CONFIG_W1_EEPROM_DS24XXX=y
CONFIG_OF_LIBFDT_OVERLAY=y