u-boot/configs/odroid-n2_defconfig
Tom Rini a09fea1d28 env: Finish migration of common ENV options
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00

58 lines
1.4 KiB
Plaintext

CONFIG_ARM=y
CONFIG_SYS_BOARD="w400"
CONFIG_ARCH_MESON=y
CONFIG_SYS_TEXT_BASE=0x01000000
CONFIG_MESON_G12A=y
CONFIG_ENV_SIZE=0x2000
CONFIG_NR_DRAM_BANKS=1
CONFIG_DEBUG_UART_BASE=0xff803000
CONFIG_DEBUG_UART_CLOCK=24000000
CONFIG_IDENT_STRING=" odroid-n2"
CONFIG_DEBUG_UART=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_MISC_INIT_R=y
# CONFIG_DISPLAY_CPUINFO is not set
# CONFIG_CMD_BDI is not set
# CONFIG_CMD_IMI is not set
CONFIG_CMD_GPIO=y
# CONFIG_CMD_LOADS is not set
CONFIG_CMD_MMC=y
CONFIG_CMD_USB=y
CONFIG_CMD_USB_MASS_STORAGE=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_REGULATOR=y
CONFIG_OF_CONTROL=y
CONFIG_DEFAULT_DEVICE_TREE="meson-g12b-odroid-n2"
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM_GPIO=y
CONFIG_DM_MMC=y
CONFIG_MMC_MESON_GX=y
CONFIG_PHY_REALTEK=y
CONFIG_DM_ETH=y
CONFIG_ETH_DESIGNWARE=y
CONFIG_MESON_G12A_USB_PHY=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_MESON_G12A=y
CONFIG_DM_REGULATOR=y
CONFIG_DM_REGULATOR_FIXED=y
CONFIG_DM_RESET=y
CONFIG_DEBUG_UART_MESON=y
CONFIG_DEBUG_UART_ANNOUNCE=y
CONFIG_DEBUG_UART_SKIP_INIT=y
CONFIG_MESON_SERIAL=y
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_USB_XHCI_HCD=y
CONFIG_USB_XHCI_DWC3=y
CONFIG_USB_DWC3=y
# CONFIG_USB_DWC3_GADGET is not set
CONFIG_USB_DWC3_MESON_G12A=y
CONFIG_USB_GADGET=y
CONFIG_USB_GADGET_VENDOR_NUM=0x1b8e
CONFIG_USB_GADGET_PRODUCT_NUM=0xfada
CONFIG_USB_GADGET_DWC2_OTG=y
CONFIG_USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8=y
CONFIG_USB_GADGET_DOWNLOAD=y
CONFIG_OF_LIBFDT_OVERLAY=y