mirror of
https://github.com/u-boot/u-boot.git
synced 2024-12-24 12:13:28 +08:00
61436d502b
The AXP209 LDO3 regulator supports voltage rate control, or can set a slew rate. This allows for the power to gradually rise up to the desired voltage, instead of spiking up as fast as possible. Reason to have this can be to reduce the inrush currents for example. There are 3 slopes to choose from, the default, 'none' is a voltage rise of 0.0167 V/uS, a 1.6 mV/uS and a 0.8 mV/uS voltage rise. In ideal world (where vendors follow the recommended design guidelines) this setting should not be enabled by default. Unless of course AXP209 crashes instead of reporting overcurrent condition as it normally should do in this case. Signed-off-by: Olliver Schinagl <oliver@schinagl.nl> Signed-off-by: Priit Laes <plaes@plaes.org> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
87 lines
2.7 KiB
C
87 lines
2.7 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* (C) Copyright 2012 Henrik Nordstrom <henrik@henriknordstrom.net>
|
|
*/
|
|
|
|
#include <linux/bitops.h>
|
|
|
|
enum axp209_reg {
|
|
AXP209_POWER_STATUS = 0x00,
|
|
AXP209_CHIP_VERSION = 0x03,
|
|
AXP209_OUTPUT_CTRL = 0x12,
|
|
AXP209_DCDC2_VOLTAGE = 0x23,
|
|
AXP209_VRC_DCDC2_LDO3 = 0x25,
|
|
AXP209_DCDC3_VOLTAGE = 0x27,
|
|
AXP209_LDO24_VOLTAGE = 0x28,
|
|
AXP209_LDO3_VOLTAGE = 0x29,
|
|
AXP209_IRQ_ENABLE1 = 0x40,
|
|
AXP209_IRQ_ENABLE2 = 0x41,
|
|
AXP209_IRQ_ENABLE3 = 0x42,
|
|
AXP209_IRQ_ENABLE4 = 0x43,
|
|
AXP209_IRQ_ENABLE5 = 0x44,
|
|
AXP209_IRQ_STATUS5 = 0x4c,
|
|
AXP209_SHUTDOWN = 0x32,
|
|
};
|
|
|
|
#define AXP209_POWER_STATUS_ON_BY_DC BIT(0)
|
|
#define AXP209_POWER_STATUS_VBUS_USABLE BIT(4)
|
|
|
|
#define AXP209_CHIP_VERSION_MASK 0x0f
|
|
|
|
#define AXP209_OUTPUT_CTRL_EXTEN BIT(0)
|
|
#define AXP209_OUTPUT_CTRL_DCDC3 BIT(1)
|
|
#define AXP209_OUTPUT_CTRL_LDO2 BIT(2)
|
|
#define AXP209_OUTPUT_CTRL_LDO4 BIT(3)
|
|
#define AXP209_OUTPUT_CTRL_DCDC2 BIT(4)
|
|
#define AXP209_OUTPUT_CTRL_LDO3 BIT(6)
|
|
|
|
/*
|
|
* AXP209 datasheet contains wrong information about LDO3 VRC:
|
|
* - VRC is actually enabled when BIT(1) is True
|
|
* - VRC is actually not enabled by default (BIT(3) = 0 after reset)
|
|
*/
|
|
#define AXP209_VRC_LDO3_EN BIT(3)
|
|
#define AXP209_VRC_DCDC2_EN BIT(2)
|
|
#define AXP209_VRC_LDO3_800uV_uS (BIT(1) | AXP209_VRC_LDO3_EN)
|
|
#define AXP209_VRC_LDO3_1600uV_uS AXP209_VRC_LDO3_EN
|
|
#define AXP209_VRC_DCDC2_800uV_uS (BIT(0) | AXP209_VRC_DCDC2_EN)
|
|
#define AXP209_VRC_DCDC2_1600uV_uS AXP209_VRC_DCDC2_EN
|
|
#define AXP209_VRC_LDO3_MASK 0xa
|
|
#define AXP209_VRC_DCDC2_MASK 0x5
|
|
#define AXP209_VRC_DCDC2_SLOPE_SET(reg, cfg) \
|
|
(((reg) & ~AXP209_VRC_DCDC2_MASK) | \
|
|
((cfg) & AXP209_VRC_DCDC2_MASK))
|
|
#define AXP209_VRC_LDO3_SLOPE_SET(reg, cfg) \
|
|
(((reg) & ~AXP209_VRC_LDO3_MASK) | \
|
|
((cfg) & AXP209_VRC_LDO3_MASK))
|
|
|
|
#define AXP209_LDO24_LDO2_MASK 0xf0
|
|
#define AXP209_LDO24_LDO4_MASK 0x0f
|
|
#define AXP209_LDO24_LDO2_SET(reg, cfg) \
|
|
(((reg) & ~AXP209_LDO24_LDO2_MASK) | \
|
|
(((cfg) << 4) & AXP209_LDO24_LDO2_MASK))
|
|
#define AXP209_LDO24_LDO4_SET(reg, cfg) \
|
|
(((reg) & ~AXP209_LDO24_LDO4_MASK) | \
|
|
(((cfg) << 0) & AXP209_LDO24_LDO4_MASK))
|
|
|
|
#define AXP209_LDO3_VOLTAGE_FROM_LDO3IN BIT(7)
|
|
#define AXP209_LDO3_VOLTAGE_MASK 0x7f
|
|
#define AXP209_LDO3_VOLTAGE_SET(x) ((x) & AXP209_LDO3_VOLTAGE_MASK)
|
|
|
|
#define AXP209_IRQ5_PEK_UP BIT(6)
|
|
#define AXP209_IRQ5_PEK_DOWN BIT(5)
|
|
|
|
#define AXP209_POWEROFF BIT(7)
|
|
|
|
/* For axp_gpio.c */
|
|
#define AXP_POWER_STATUS 0x00
|
|
#define AXP_POWER_STATUS_VBUS_PRESENT BIT(5)
|
|
#define AXP_GPIO0_CTRL 0x90
|
|
#define AXP_GPIO1_CTRL 0x92
|
|
#define AXP_GPIO2_CTRL 0x93
|
|
#define AXP_GPIO_CTRL_OUTPUT_LOW 0x00 /* Drive pin low */
|
|
#define AXP_GPIO_CTRL_OUTPUT_HIGH 0x01 /* Drive pin high */
|
|
#define AXP_GPIO_CTRL_INPUT 0x02 /* Input */
|
|
#define AXP_GPIO_STATE 0x94
|
|
#define AXP_GPIO_STATE_OFFSET 4
|