mirror of
https://github.com/u-boot/u-boot.git
synced 2024-11-28 15:13:31 +08:00
c05ed00afb
Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
499 lines
12 KiB
C
499 lines
12 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright (C) 2013 Freescale Semiconductor, Inc.
|
|
* Copyright (C) 2014 O.S. Systems Software LTDA.
|
|
*
|
|
* Author: Fabio Estevam <fabio.estevam@freescale.com>
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <image.h>
|
|
#include <init.h>
|
|
#include <log.h>
|
|
#include <asm/arch/clock.h>
|
|
#include <asm/arch/crm_regs.h>
|
|
#include <asm/arch/iomux.h>
|
|
#include <asm/arch/imx-regs.h>
|
|
#include <asm/arch/mx6-pins.h>
|
|
#include <asm/arch/mxc_hdmi.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <asm/gpio.h>
|
|
#include <asm/mach-imx/iomux-v3.h>
|
|
#include <asm/mach-imx/mxc_i2c.h>
|
|
#include <asm/mach-imx/boot_mode.h>
|
|
#include <asm/mach-imx/video.h>
|
|
#include <asm/mach-imx/sata.h>
|
|
#include <asm/io.h>
|
|
#include <env.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/sizes.h>
|
|
#include <common.h>
|
|
#include <miiphy.h>
|
|
#include <netdev.h>
|
|
#include <phy.h>
|
|
#include <i2c.h>
|
|
#include <power/pmic.h>
|
|
#include <power/pfuze100_pmic.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
|
|
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
|
|
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
|
|
|
|
#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
|
|
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
|
|
|
|
#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
|
|
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
|
|
PAD_CTL_ODE | PAD_CTL_SRE_FAST)
|
|
|
|
#define ETH_PHY_RESET IMX_GPIO_NR(3, 29)
|
|
#define ETH_PHY_AR8035_POWER IMX_GPIO_NR(7, 13)
|
|
#define REV_DETECTION IMX_GPIO_NR(2, 28)
|
|
|
|
/* Speed defined in Kconfig is only applicable when not using DM_I2C. */
|
|
#ifdef CONFIG_DM_I2C
|
|
#define I2C1_SPEED_NON_DM 0
|
|
#define I2C2_SPEED_NON_DM 0
|
|
#else
|
|
#define I2C1_SPEED_NON_DM CONFIG_SYS_MXC_I2C1_SPEED
|
|
#define I2C2_SPEED_NON_DM CONFIG_SYS_MXC_I2C2_SPEED
|
|
#endif
|
|
|
|
static bool with_pmic;
|
|
|
|
int dram_init(void)
|
|
{
|
|
gd->ram_size = imx_ddr_size();
|
|
|
|
return 0;
|
|
}
|
|
|
|
static iomux_v3_cfg_t const uart1_pads[] = {
|
|
IOMUX_PADS(PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
|
|
IOMUX_PADS(PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
|
|
};
|
|
|
|
static iomux_v3_cfg_t const enet_pads[] = {
|
|
/* AR8031 PHY Reset */
|
|
IOMUX_PADS(PAD_EIM_D29__GPIO3_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL)),
|
|
};
|
|
|
|
static iomux_v3_cfg_t const enet_ar8035_power_pads[] = {
|
|
/* AR8035 POWER */
|
|
IOMUX_PADS(PAD_GPIO_18__GPIO7_IO13 | MUX_PAD_CTRL(NO_PAD_CTRL)),
|
|
};
|
|
|
|
static iomux_v3_cfg_t const rev_detection_pad[] = {
|
|
IOMUX_PADS(PAD_EIM_EB0__GPIO2_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL)),
|
|
};
|
|
|
|
static void setup_iomux_uart(void)
|
|
{
|
|
SETUP_IOMUX_PADS(uart1_pads);
|
|
}
|
|
|
|
static void setup_iomux_enet(void)
|
|
{
|
|
SETUP_IOMUX_PADS(enet_pads);
|
|
|
|
if (with_pmic) {
|
|
SETUP_IOMUX_PADS(enet_ar8035_power_pads);
|
|
/* enable AR8035 POWER */
|
|
gpio_request(ETH_PHY_AR8035_POWER, "PHY_POWER");
|
|
gpio_direction_output(ETH_PHY_AR8035_POWER, 0);
|
|
}
|
|
/* wait until 3.3V of PHY and clock become stable */
|
|
mdelay(10);
|
|
|
|
/* Reset AR8031 PHY */
|
|
gpio_request(ETH_PHY_RESET, "PHY_RESET");
|
|
gpio_direction_output(ETH_PHY_RESET, 0);
|
|
mdelay(10);
|
|
gpio_set_value(ETH_PHY_RESET, 1);
|
|
udelay(100);
|
|
}
|
|
|
|
static int ar8031_phy_fixup(struct phy_device *phydev)
|
|
{
|
|
unsigned short val;
|
|
int mask;
|
|
|
|
/* To enable AR8031 ouput a 125MHz clk from CLK_25M */
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
|
|
|
|
val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
|
|
if (with_pmic)
|
|
mask = 0xffe7; /* AR8035 */
|
|
else
|
|
mask = 0xffe3; /* AR8031 */
|
|
|
|
val &= mask;
|
|
val |= 0x18;
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
|
|
|
|
/* introduce tx clock delay */
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
|
|
val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
|
|
val |= 0x0100;
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_phy_config(struct phy_device *phydev)
|
|
{
|
|
ar8031_phy_fixup(phydev);
|
|
|
|
if (phydev->drv->config)
|
|
phydev->drv->config(phydev);
|
|
|
|
return 0;
|
|
}
|
|
|
|
#if defined(CONFIG_VIDEO_IPUV3)
|
|
struct i2c_pads_info mx6q_i2c2_pad_info = {
|
|
.scl = {
|
|
.i2c_mode = MX6Q_PAD_KEY_COL3__I2C2_SCL
|
|
| MUX_PAD_CTRL(I2C_PAD_CTRL),
|
|
.gpio_mode = MX6Q_PAD_KEY_COL3__GPIO4_IO12
|
|
| MUX_PAD_CTRL(I2C_PAD_CTRL),
|
|
.gp = IMX_GPIO_NR(4, 12)
|
|
},
|
|
.sda = {
|
|
.i2c_mode = MX6Q_PAD_KEY_ROW3__I2C2_SDA
|
|
| MUX_PAD_CTRL(I2C_PAD_CTRL),
|
|
.gpio_mode = MX6Q_PAD_KEY_ROW3__GPIO4_IO13
|
|
| MUX_PAD_CTRL(I2C_PAD_CTRL),
|
|
.gp = IMX_GPIO_NR(4, 13)
|
|
}
|
|
};
|
|
|
|
struct i2c_pads_info mx6dl_i2c2_pad_info = {
|
|
.scl = {
|
|
.i2c_mode = MX6DL_PAD_KEY_COL3__I2C2_SCL
|
|
| MUX_PAD_CTRL(I2C_PAD_CTRL),
|
|
.gpio_mode = MX6DL_PAD_KEY_COL3__GPIO4_IO12
|
|
| MUX_PAD_CTRL(I2C_PAD_CTRL),
|
|
.gp = IMX_GPIO_NR(4, 12)
|
|
},
|
|
.sda = {
|
|
.i2c_mode = MX6DL_PAD_KEY_ROW3__I2C2_SDA
|
|
| MUX_PAD_CTRL(I2C_PAD_CTRL),
|
|
.gpio_mode = MX6DL_PAD_KEY_ROW3__GPIO4_IO13
|
|
| MUX_PAD_CTRL(I2C_PAD_CTRL),
|
|
.gp = IMX_GPIO_NR(4, 13)
|
|
}
|
|
};
|
|
|
|
struct i2c_pads_info mx6q_i2c3_pad_info = {
|
|
.scl = {
|
|
.i2c_mode = MX6Q_PAD_GPIO_5__I2C3_SCL
|
|
| MUX_PAD_CTRL(I2C_PAD_CTRL),
|
|
.gpio_mode = MX6Q_PAD_GPIO_5__GPIO1_IO05
|
|
| MUX_PAD_CTRL(I2C_PAD_CTRL),
|
|
.gp = IMX_GPIO_NR(1, 5)
|
|
},
|
|
.sda = {
|
|
.i2c_mode = MX6Q_PAD_GPIO_16__I2C3_SDA
|
|
| MUX_PAD_CTRL(I2C_PAD_CTRL),
|
|
.gpio_mode = MX6Q_PAD_GPIO_16__GPIO7_IO11
|
|
| MUX_PAD_CTRL(I2C_PAD_CTRL),
|
|
.gp = IMX_GPIO_NR(7, 11)
|
|
}
|
|
};
|
|
|
|
struct i2c_pads_info mx6dl_i2c3_pad_info = {
|
|
.scl = {
|
|
.i2c_mode = MX6DL_PAD_GPIO_5__I2C3_SCL
|
|
| MUX_PAD_CTRL(I2C_PAD_CTRL),
|
|
.gpio_mode = MX6DL_PAD_GPIO_5__GPIO1_IO05
|
|
| MUX_PAD_CTRL(I2C_PAD_CTRL),
|
|
.gp = IMX_GPIO_NR(1, 5)
|
|
},
|
|
.sda = {
|
|
.i2c_mode = MX6DL_PAD_GPIO_16__I2C3_SDA
|
|
| MUX_PAD_CTRL(I2C_PAD_CTRL),
|
|
.gpio_mode = MX6DL_PAD_GPIO_16__GPIO7_IO11
|
|
| MUX_PAD_CTRL(I2C_PAD_CTRL),
|
|
.gp = IMX_GPIO_NR(7, 11)
|
|
}
|
|
};
|
|
|
|
static iomux_v3_cfg_t const fwadapt_7wvga_pads[] = {
|
|
IOMUX_PADS(PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK),
|
|
IOMUX_PADS(PAD_DI0_PIN2__IPU1_DI0_PIN02), /* HSync */
|
|
IOMUX_PADS(PAD_DI0_PIN3__IPU1_DI0_PIN03), /* VSync */
|
|
IOMUX_PADS(PAD_DI0_PIN4__IPU1_DI0_PIN04 | MUX_PAD_CTRL(PAD_CTL_DSE_120ohm)), /* Contrast */
|
|
IOMUX_PADS(PAD_DI0_PIN15__IPU1_DI0_PIN15), /* DISP0_DRDY */
|
|
IOMUX_PADS(PAD_DISP0_DAT0__IPU1_DISP0_DATA00),
|
|
IOMUX_PADS(PAD_DISP0_DAT1__IPU1_DISP0_DATA01),
|
|
IOMUX_PADS(PAD_DISP0_DAT2__IPU1_DISP0_DATA02),
|
|
IOMUX_PADS(PAD_DISP0_DAT3__IPU1_DISP0_DATA03),
|
|
IOMUX_PADS(PAD_DISP0_DAT4__IPU1_DISP0_DATA04),
|
|
IOMUX_PADS(PAD_DISP0_DAT5__IPU1_DISP0_DATA05),
|
|
IOMUX_PADS(PAD_DISP0_DAT6__IPU1_DISP0_DATA06),
|
|
IOMUX_PADS(PAD_DISP0_DAT7__IPU1_DISP0_DATA07),
|
|
IOMUX_PADS(PAD_DISP0_DAT8__IPU1_DISP0_DATA08),
|
|
IOMUX_PADS(PAD_DISP0_DAT9__IPU1_DISP0_DATA09),
|
|
IOMUX_PADS(PAD_DISP0_DAT10__IPU1_DISP0_DATA10),
|
|
IOMUX_PADS(PAD_DISP0_DAT11__IPU1_DISP0_DATA11),
|
|
IOMUX_PADS(PAD_DISP0_DAT12__IPU1_DISP0_DATA12),
|
|
IOMUX_PADS(PAD_DISP0_DAT13__IPU1_DISP0_DATA13),
|
|
IOMUX_PADS(PAD_DISP0_DAT14__IPU1_DISP0_DATA14),
|
|
IOMUX_PADS(PAD_DISP0_DAT15__IPU1_DISP0_DATA15),
|
|
IOMUX_PADS(PAD_DISP0_DAT16__IPU1_DISP0_DATA16),
|
|
IOMUX_PADS(PAD_DISP0_DAT17__IPU1_DISP0_DATA17),
|
|
IOMUX_PADS(PAD_SD4_DAT2__GPIO2_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL)), /* DISP0_BKLEN */
|
|
IOMUX_PADS(PAD_SD4_DAT3__GPIO2_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL)), /* DISP0_VDDEN */
|
|
};
|
|
|
|
static void do_enable_hdmi(struct display_info_t const *dev)
|
|
{
|
|
imx_enable_hdmi_phy();
|
|
}
|
|
|
|
static int detect_i2c(struct display_info_t const *dev)
|
|
{
|
|
#ifdef CONFIG_DM_I2C
|
|
struct udevice *bus, *udev;
|
|
int rc;
|
|
|
|
rc = uclass_get_device_by_seq(UCLASS_I2C, dev->bus, &bus);
|
|
if (rc)
|
|
return rc;
|
|
rc = dm_i2c_probe(bus, dev->addr, 0, &udev);
|
|
if (rc)
|
|
return 0;
|
|
return 1;
|
|
#else
|
|
return (0 == i2c_set_bus_num(dev->bus)) &&
|
|
(0 == i2c_probe(dev->addr));
|
|
#endif
|
|
}
|
|
|
|
static void enable_fwadapt_7wvga(struct display_info_t const *dev)
|
|
{
|
|
SETUP_IOMUX_PADS(fwadapt_7wvga_pads);
|
|
|
|
gpio_request(IMX_GPIO_NR(2, 10), "DISP0_BKLEN");
|
|
gpio_request(IMX_GPIO_NR(2, 11), "DISP0_VDDEN");
|
|
gpio_direction_output(IMX_GPIO_NR(2, 10), 1);
|
|
gpio_direction_output(IMX_GPIO_NR(2, 11), 1);
|
|
}
|
|
|
|
struct display_info_t const displays[] = {{
|
|
.bus = -1,
|
|
.addr = 0,
|
|
.pixfmt = IPU_PIX_FMT_RGB24,
|
|
.detect = detect_hdmi,
|
|
.enable = do_enable_hdmi,
|
|
.mode = {
|
|
.name = "HDMI",
|
|
.refresh = 60,
|
|
.xres = 1024,
|
|
.yres = 768,
|
|
.pixclock = 15385,
|
|
.left_margin = 220,
|
|
.right_margin = 40,
|
|
.upper_margin = 21,
|
|
.lower_margin = 7,
|
|
.hsync_len = 60,
|
|
.vsync_len = 10,
|
|
.sync = FB_SYNC_EXT,
|
|
.vmode = FB_VMODE_NONINTERLACED
|
|
} }, {
|
|
.bus = 1,
|
|
.addr = 0x10,
|
|
.pixfmt = IPU_PIX_FMT_RGB666,
|
|
.detect = detect_i2c,
|
|
.enable = enable_fwadapt_7wvga,
|
|
.mode = {
|
|
.name = "FWBADAPT-LCD-F07A-0102",
|
|
.refresh = 60,
|
|
.xres = 800,
|
|
.yres = 480,
|
|
.pixclock = 33260,
|
|
.left_margin = 128,
|
|
.right_margin = 128,
|
|
.upper_margin = 22,
|
|
.lower_margin = 22,
|
|
.hsync_len = 1,
|
|
.vsync_len = 1,
|
|
.sync = 0,
|
|
.vmode = FB_VMODE_NONINTERLACED
|
|
} } };
|
|
size_t display_count = ARRAY_SIZE(displays);
|
|
|
|
static void setup_display(void)
|
|
{
|
|
struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
|
|
int reg;
|
|
|
|
enable_ipu_clock();
|
|
imx_setup_hdmi();
|
|
|
|
reg = readl(&mxc_ccm->chsccdr);
|
|
reg |= (CHSCCDR_CLK_SEL_LDB_DI0
|
|
<< MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
|
|
writel(reg, &mxc_ccm->chsccdr);
|
|
|
|
/* Disable LCD backlight */
|
|
SETUP_IOMUX_PAD(PAD_DI0_PIN4__GPIO4_IO20);
|
|
gpio_request(IMX_GPIO_NR(4, 20), "LCD_BKLEN");
|
|
gpio_direction_input(IMX_GPIO_NR(4, 20));
|
|
}
|
|
#endif /* CONFIG_VIDEO_IPUV3 */
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
setup_iomux_uart();
|
|
#ifdef CONFIG_SATA
|
|
setup_sata();
|
|
#endif
|
|
|
|
return 0;
|
|
}
|
|
|
|
#define PMIC_I2C_BUS 2
|
|
|
|
int power_init_board(void)
|
|
{
|
|
struct udevice *dev;
|
|
int reg, ret;
|
|
|
|
ret = pmic_get("pfuze100@8", &dev);
|
|
if (ret < 0) {
|
|
debug("pmic_get() ret %d\n", ret);
|
|
return 0;
|
|
}
|
|
|
|
reg = pmic_reg_read(dev, PFUZE100_DEVICEID);
|
|
if (reg < 0) {
|
|
debug("pmic_reg_read() ret %d\n", reg);
|
|
return 0;
|
|
}
|
|
printf("PMIC: PFUZE100 ID=0x%02x\n", reg);
|
|
with_pmic = true;
|
|
|
|
/* Set VGEN2 to 1.5V and enable */
|
|
reg = pmic_reg_read(dev, PFUZE100_VGEN2VOL);
|
|
reg &= ~(LDO_VOL_MASK);
|
|
reg |= (LDOA_1_50V | (1 << (LDO_EN)));
|
|
pmic_reg_write(dev, PFUZE100_VGEN2VOL, reg);
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* Do not overwrite the console
|
|
* Use always serial for U-Boot console
|
|
*/
|
|
int overwrite_console(void)
|
|
{
|
|
return 1;
|
|
}
|
|
|
|
#ifdef CONFIG_CMD_BMODE
|
|
static const struct boot_mode board_boot_modes[] = {
|
|
/* 4 bit bus width */
|
|
{"mmc0", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
|
|
{"mmc1", MAKE_CFGVAL(0x40, 0x20, 0x00, 0x00)},
|
|
{NULL, 0},
|
|
};
|
|
#endif
|
|
|
|
static bool is_revc1(void)
|
|
{
|
|
SETUP_IOMUX_PADS(rev_detection_pad);
|
|
gpio_request(REV_DETECTION, "REV_DETECT");
|
|
gpio_direction_input(REV_DETECTION);
|
|
|
|
if (gpio_get_value(REV_DETECTION))
|
|
return true;
|
|
else
|
|
return false;
|
|
}
|
|
|
|
static bool is_revd1(void)
|
|
{
|
|
if (with_pmic)
|
|
return true;
|
|
else
|
|
return false;
|
|
}
|
|
|
|
int board_late_init(void)
|
|
{
|
|
#ifdef CONFIG_CMD_BMODE
|
|
add_board_boot_modes(board_boot_modes);
|
|
#endif
|
|
|
|
#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
|
|
if (is_mx6dqp())
|
|
env_set("board_rev", "MX6QP");
|
|
else if (is_mx6dq())
|
|
env_set("board_rev", "MX6Q");
|
|
else
|
|
env_set("board_rev", "MX6DL");
|
|
|
|
if (is_revd1())
|
|
env_set("board_name", "D1");
|
|
else if (is_revc1())
|
|
env_set("board_name", "C1");
|
|
else
|
|
env_set("board_name", "B1");
|
|
#endif
|
|
setup_iomux_enet();
|
|
|
|
if (is_revd1())
|
|
puts("Board: Wandboard rev D1\n");
|
|
else if (is_revc1())
|
|
puts("Board: Wandboard rev C1\n");
|
|
else
|
|
puts("Board: Wandboard rev B1\n");
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_init(void)
|
|
{
|
|
/* address of boot parameters */
|
|
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
|
|
|
|
#if defined(CONFIG_VIDEO_IPUV3)
|
|
setup_i2c(1, I2C1_SPEED_NON_DM, 0x7f, &mx6dl_i2c2_pad_info);
|
|
if (is_mx6dq() || is_mx6dqp()) {
|
|
setup_i2c(1, I2C1_SPEED_NON_DM, 0x7f, &mx6q_i2c2_pad_info);
|
|
setup_i2c(2, I2C2_SPEED_NON_DM, 0x7f, &mx6q_i2c3_pad_info);
|
|
} else {
|
|
setup_i2c(1, I2C1_SPEED_NON_DM, 0x7f, &mx6dl_i2c2_pad_info);
|
|
setup_i2c(2, I2C2_SPEED_NON_DM, 0x7f, &mx6dl_i2c3_pad_info);
|
|
}
|
|
|
|
setup_display();
|
|
#endif
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_SPL_LOAD_FIT
|
|
int board_fit_config_name_match(const char *name)
|
|
{
|
|
if (is_mx6dq()) {
|
|
if (!strcmp(name, "imx6q-wandboard-revd1"))
|
|
return 0;
|
|
} else if (is_mx6dqp()) {
|
|
if (!strcmp(name, "imx6qp-wandboard-revd1"))
|
|
return 0;
|
|
} else if (is_mx6dl() || is_mx6solo()) {
|
|
if (!strcmp(name, "imx6dl-wandboard-revd1"))
|
|
return 0;
|
|
}
|
|
|
|
return -EINVAL;
|
|
}
|
|
#endif
|