mirror of
https://github.com/u-boot/u-boot.git
synced 2024-12-02 17:13:28 +08:00
1a4596601f
Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
152 lines
4.8 KiB
INI
152 lines
4.8 KiB
INI
#
|
|
# Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
|
|
#
|
|
# Based on Kirkwood support:
|
|
# (C) Copyright 2009
|
|
# Marvell Semiconductor <www.marvell.com>
|
|
# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
|
|
#
|
|
# SPDX-License-Identifier: GPL-2.0+
|
|
#
|
|
# Refer doc/README.kwbimage for more details about how-to configure
|
|
# and create kirkwood boot image
|
|
#
|
|
|
|
# Boot Media configurations
|
|
BOOT_FROM spi # Boot from SPI flash
|
|
|
|
# SOC registers configuration using bootrom header extension
|
|
# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
|
|
|
|
# Configure RGMII-0 interface pad voltage to 1.8V
|
|
DATA 0xFFD100e0 0x1B1B1B9B
|
|
|
|
#Dram initalization for SINGLE x16 CL=5 @ 400MHz
|
|
DATA 0xFFD01400 0x43000618 # DDR Configuration register
|
|
# bit13-0: 0xa00 (2560 DDR2 clks refresh rate)
|
|
# bit23-14: zero
|
|
# bit24: 1= enable exit self refresh mode on DDR access
|
|
# bit25: 1 required
|
|
# bit29-26: zero
|
|
# bit31-30: 01
|
|
|
|
DATA 0xFFD01404 0x35143000 # DDR Controller Control Low
|
|
# bit 4: 0=addr/cmd in smame cycle
|
|
# bit 5: 0=clk is driven during self refresh, we don't care for APX
|
|
# bit 6: 0=use recommended falling edge of clk for addr/cmd
|
|
# bit14: 0=input buffer always powered up
|
|
# bit18: 1=cpu lock transaction enabled
|
|
# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
|
|
# bit27-24: 8= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
|
|
# bit30-28: 3 required
|
|
# bit31: 0=no additional STARTBURST delay
|
|
|
|
DATA 0xFFD01408 0x11012228 # DDR Timing (Low) (active cycles value +1)
|
|
# bit7-4: TRCD
|
|
# bit11- 8: TRP
|
|
# bit15-12: TWR
|
|
# bit19-16: TWTR
|
|
# bit20: TRAS msb
|
|
# bit23-21: 0x0
|
|
# bit27-24: TRRD
|
|
# bit31-28: TRTP
|
|
|
|
DATA 0xFFD0140C 0x00000A19 # DDR Timing (High)
|
|
# bit6-0: TRFC
|
|
# bit8-7: TR2R
|
|
# bit10-9: TR2W
|
|
# bit12-11: TW2W
|
|
# bit31-13: zero required
|
|
|
|
DATA 0xFFD01410 0x0000000C # DDR Address Control
|
|
# bit1-0: 00, Cs0width=x8
|
|
# bit3-2: 11, Cs0size=1Gb
|
|
# bit5-4: 00, Cs2width=nonexistent
|
|
# bit7-6: 00, Cs1size =nonexistent
|
|
# bit9-8: 00, Cs2width=nonexistent
|
|
# bit11-10: 00, Cs2size =nonexistent
|
|
# bit13-12: 00, Cs3width=nonexistent
|
|
# bit15-14: 00, Cs3size =nonexistent
|
|
# bit16: 0, Cs0AddrSel
|
|
# bit17: 0, Cs1AddrSel
|
|
# bit18: 0, Cs2AddrSel
|
|
# bit19: 0, Cs3AddrSel
|
|
# bit31-20: 0 required
|
|
|
|
DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
|
|
# bit0: 0, OpenPage enabled
|
|
# bit31-1: 0 required
|
|
|
|
DATA 0xFFD01418 0x00000000 # DDR Operation
|
|
# bit3-0: 0x0, DDR cmd
|
|
# bit31-4: 0 required
|
|
|
|
DATA 0xFFD0141C 0x00000632 # DDR Mode
|
|
# bit2-0: 2, BurstLen=2 required
|
|
# bit3: 0, BurstType=0 required
|
|
# bit6-4: 4, CL=5
|
|
# bit7: 0, TestMode=0 normal
|
|
# bit8: 0, DLL reset=0 normal
|
|
# bit11-9: 6, auto-precharge write recovery ????????????
|
|
# bit12: 0, PD must be zero
|
|
# bit31-13: 0 required
|
|
|
|
DATA 0xFFD01420 0x00000004 # DDR Extended Mode
|
|
# bit0: 0, DDR DLL enabled
|
|
# bit1: 1, DDR drive strenght reduced
|
|
# bit2: 1, DDR ODT control lsd enabled
|
|
# bit5-3: 000, required
|
|
# bit6: 1, DDR ODT control msb, enabled
|
|
# bit9-7: 000, required
|
|
# bit10: 0, differential DQS enabled
|
|
# bit11: 0, required
|
|
# bit12: 0, DDR output buffer enabled
|
|
# bit31-13: 0 required
|
|
|
|
DATA 0xFFD01424 0x0000F07F # DDR Controller Control High
|
|
# bit2-0: 111, required
|
|
# bit3 : 1 , MBUS Burst Chop disabled
|
|
# bit6-4: 111, required
|
|
# bit7 : 1 , D2P Latency enabled
|
|
# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
|
|
# bit9 : 0 , no half clock cycle addition to dataout
|
|
# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
|
|
# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
|
|
# bit15-12: 1111 required
|
|
# bit31-16: 0 required
|
|
|
|
DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
|
|
DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
|
|
|
|
DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
|
|
DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size
|
|
# bit0: 1, Window enabled
|
|
# bit1: 0, Write Protect disabled
|
|
# bit3-2: 00, CS0 hit selected
|
|
# bit23-4: ones, required
|
|
# bit31-24: 0x07, Size (i.e. 128MB)
|
|
|
|
DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled
|
|
DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
|
|
DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
|
|
|
|
DATA 0xFFD01494 0x00010000 # DDR ODT Control (Low)
|
|
# bit3-0: 1, ODT0Rd, MODT[0] asserted during read from DRAM CS0
|
|
# bit19-16:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0
|
|
|
|
DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
|
|
# bit1-0: 00, ODT0 controlled by ODT Control (low) register above
|
|
# bit3-2: 01, ODT1 active NEVER!
|
|
# bit31-4: zero, required
|
|
|
|
DATA 0xFFD0149C 0x0000E40F # CPU ODT Control
|
|
# bit3-0: 1, ODT0Rd, Internal ODT asserted during read from DRAM bank0
|
|
# bit7-4: 1, ODT0Wr, Internal ODT asserted during write to DRAM bank0
|
|
# bit11-10:1, DQ_ODTSel. ODT select turned on
|
|
|
|
DATA 0xFFD01480 0x00000001 # DDR Initialization Control
|
|
#bit0=1, enable DDR init upon this register write
|
|
|
|
# End of Header extension
|
|
DATA 0x0 0x0
|