mirror of
https://github.com/u-boot/u-boot.git
synced 2024-11-30 08:03:32 +08:00
79e4e6480b
Replace environmental variables memctl_intlv_ctl and ba_intlv_ctl with
hwconfig parameters. The syntax is
setenv hwconfig "fsl_ddr:ctlr_intlv=<mode>,bank_intlv=<mode>"
The mode values for memory controller interleaving are
cacheline
page
bank
superbank
The mode values for bank interleaving are
cs0_cs1
cs2_cs3
cs0_cs1_and_cs2_cs3
cs0_cs1_cs2_cs3
Signed-off-by: York Sun <yorksun@freescale.com>
73 lines
3.3 KiB
Plaintext
73 lines
3.3 KiB
Plaintext
|
|
Table of interleaving modes supported in cpu/8xxx/ddr/
|
|
======================================================
|
|
+-------------+---------------------------------------------------------+
|
|
| | Rank Interleaving |
|
|
| +--------+-----------+-----------+------------+-----------+
|
|
|Memory | | | | 2x2 | 4x1 |
|
|
|Controller | None | 2x1 lower | 2x1 upper | {CS0+CS1}, | {CS0+CS1+ |
|
|
|Interleaving | | {CS0+CS1} | {CS2+CS3} | {CS2+CS3} | CS2+CS3} |
|
|
+-------------+--------+-----------+-----------+------------+-----------+
|
|
|None | Yes | Yes | Yes | Yes | Yes |
|
|
+-------------+--------+-----------+-----------+------------+-----------+
|
|
|Cacheline | Yes | Yes | No | No, Only(*)| Yes |
|
|
| |CS0 Only| | | {CS0+CS1} | |
|
|
+-------------+--------+-----------+-----------+------------+-----------+
|
|
|Page | Yes | Yes | No | No, Only(*)| Yes |
|
|
| |CS0 Only| | | {CS0+CS1} | |
|
|
+-------------+--------+-----------+-----------+------------+-----------+
|
|
|Bank | Yes | Yes | No | No, Only(*)| Yes |
|
|
| |CS0 Only| | | {CS0+CS1} | |
|
|
+-------------+--------+-----------+-----------+------------+-----------+
|
|
|Superbank | No | Yes | No | No, Only(*)| Yes |
|
|
| | | | | {CS0+CS1} | |
|
|
+-------------+--------+-----------+-----------+------------+-----------+
|
|
(*) Although the hardware can be configured with memory controller
|
|
interleaving using "2x2" rank interleaving, it only interleaves {CS0+CS1}
|
|
from each controller. {CS2+CS3} on each controller are only rank
|
|
interleaved on that controller.
|
|
|
|
The ways to configure the ddr interleaving mode
|
|
==============================================
|
|
1. In board header file(e.g.MPC8572DS.h), add default interleaving setting
|
|
under "CONFIG_EXTRA_ENV_SETTINGS", like:
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"hwconfig=fsl_ddr:ctlr_intlv=bank" \
|
|
......
|
|
|
|
2. Run u-boot "setenv" command to configure the memory interleaving mode.
|
|
Either numerical or string value is accepted.
|
|
|
|
# disable memory controller interleaving
|
|
setenv hwconfig "fsl_ddr:ctlr_intlv=null"
|
|
|
|
# cacheline interleaving
|
|
setenv hwconfig "fsl_ddr:ctlr_intlv=cacheline"
|
|
|
|
# page interleaving
|
|
setenv hwconfig "fsl_ddr:ctlr_intlv=page"
|
|
|
|
# bank interleaving
|
|
setenv hwconfig "fsl_ddr:ctlr_intlv=bank"
|
|
|
|
# superbank
|
|
setenv hwconfig "fsl_ddr:ctlr_intlv=superbank"
|
|
|
|
# disable bank (chip-select) interleaving
|
|
setenv hwconfig "fsl_ddr:bank_intlv=null"
|
|
|
|
# bank(chip-select) interleaving cs0+cs1
|
|
setenv hwconfig "fsl_ddr:bank_intlv=cs0_cs1"
|
|
|
|
# bank(chip-select) interleaving cs2+cs3
|
|
setenv hwconfig "fsl_ddr:bank_intlv=cs2_cs3"
|
|
|
|
# bank(chip-select) interleaving (cs0+cs1) and (cs2+cs3) (2x2)
|
|
setenv hwconfig "fsl_ddr:bank_intlv=cs0_cs1_and_cs2_cs3"
|
|
|
|
# bank(chip-select) interleaving (cs0+cs1+cs2+cs3) (4x1)
|
|
setenv hwconfig "fsl_ddr:bank_intlv=cs0_cs1_cs2_cs3"
|
|
|
|
The above memory controller interleaving and bank interleaving can be mixed. The syntax is
|
|
setenv hwconfig "fsl_ddr:ctlr_intlv=cacheline,bank_intlv=cs0_cs1"
|