mirror of
https://github.com/u-boot/u-boot.git
synced 2024-12-14 07:13:28 +08:00
a09fea1d28
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
154 lines
3.3 KiB
C
154 lines
3.3 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* WORK Microwave work_92105 board configuration file
|
|
*
|
|
* (C) Copyright 2014 DENX Software Engineering GmbH
|
|
* Written-by: Albert ARIBAUD <albert.aribaud@3adev.fr>
|
|
*/
|
|
|
|
#ifndef __CONFIG_WORK_92105_H__
|
|
#define __CONFIG_WORK_92105_H__
|
|
|
|
/* SoC and board defines */
|
|
#include <linux/sizes.h>
|
|
#include <asm/arch/cpu.h>
|
|
|
|
/*
|
|
* Define work_92105 machine type by hand -- done only for compatibility
|
|
* with original board code
|
|
*/
|
|
#define CONFIG_MACH_TYPE 736
|
|
|
|
#if !defined(CONFIG_SPL_BUILD)
|
|
#define CONFIG_SKIP_LOWLEVEL_INIT
|
|
#endif
|
|
|
|
/*
|
|
* Memory configurations
|
|
*/
|
|
#define CONFIG_SYS_MALLOC_LEN SZ_1M
|
|
#define CONFIG_SYS_SDRAM_BASE EMC_DYCS0_BASE
|
|
#define CONFIG_SYS_SDRAM_SIZE SZ_128M
|
|
#define CONFIG_SYS_MEMTEST_START (CONFIG_SYS_SDRAM_BASE + SZ_32K)
|
|
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_TEXT_BASE - SZ_1M)
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + SZ_32K)
|
|
|
|
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + SZ_512K \
|
|
- GENERATED_GBL_DATA_SIZE)
|
|
|
|
/*
|
|
* Serial Driver
|
|
*/
|
|
#define CONFIG_SYS_LPC32XX_UART 5 /* UART5 - NS16550 */
|
|
|
|
/*
|
|
* Ethernet Driver
|
|
*/
|
|
|
|
#define CONFIG_PHY_SMSC
|
|
#define CONFIG_LPC32XX_ETH
|
|
#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
|
|
/* FIXME: remove "Waiting for PHY auto negotiation to complete..." message */
|
|
|
|
/*
|
|
* I2C driver
|
|
*/
|
|
|
|
#define CONFIG_SYS_I2C_LPC32XX
|
|
#define CONFIG_SYS_I2C
|
|
#define CONFIG_SYS_I2C_SPEED 350000
|
|
|
|
/*
|
|
* I2C EEPROM
|
|
*/
|
|
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x56
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
|
|
|
|
/*
|
|
* I2C RTC
|
|
*/
|
|
|
|
#define CONFIG_RTC_DS1374
|
|
|
|
/*
|
|
* U-Boot General Configurations
|
|
*/
|
|
#define CONFIG_SYS_CBSIZE 1024
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
|
|
|
|
/*
|
|
* NAND chip timings for FIXME: which one?
|
|
*/
|
|
|
|
#define CONFIG_LPC32XX_NAND_MLC_TCEA_DELAY 333333333
|
|
#define CONFIG_LPC32XX_NAND_MLC_BUSY_DELAY 10000000
|
|
#define CONFIG_LPC32XX_NAND_MLC_NAND_TA 18181818
|
|
#define CONFIG_LPC32XX_NAND_MLC_RD_HIGH 31250000
|
|
#define CONFIG_LPC32XX_NAND_MLC_RD_LOW 45454545
|
|
#define CONFIG_LPC32XX_NAND_MLC_WR_HIGH 40000000
|
|
#define CONFIG_LPC32XX_NAND_MLC_WR_LOW 83333333
|
|
|
|
/*
|
|
* NAND
|
|
*/
|
|
|
|
/* driver configuration */
|
|
#define CONFIG_SYS_NAND_SELF_INIT
|
|
#define CONFIG_SYS_MAX_NAND_DEVICE 1
|
|
#define CONFIG_SYS_MAX_NAND_CHIPS 1
|
|
#define CONFIG_SYS_NAND_BASE MLC_NAND_BASE
|
|
#define CONFIG_NAND_LPC32XX_MLC
|
|
|
|
/*
|
|
* GPIO
|
|
*/
|
|
|
|
#define CONFIG_LPC32XX_GPIO
|
|
|
|
/*
|
|
* SSP/SPI/DISPLAY
|
|
*/
|
|
|
|
#define CONFIG_LPC32XX_SSP_TIMEOUT 100000
|
|
/*
|
|
* Environment
|
|
*/
|
|
|
|
/*
|
|
* Boot Linux
|
|
*/
|
|
#define CONFIG_CMDLINE_TAG
|
|
#define CONFIG_SETUP_MEMORY_TAGS
|
|
#define CONFIG_INITRD_TAG
|
|
|
|
#define CONFIG_BOOTFILE "uImage"
|
|
#define CONFIG_LOADADDR 0x80008000
|
|
|
|
/*
|
|
* SPL
|
|
*/
|
|
|
|
/* SPL will be executed at offset 0 */
|
|
/* SPL will use SRAM as stack */
|
|
#define CONFIG_SPL_STACK 0x0000FFF8
|
|
/* Use the framework and generic lib */
|
|
/* SPL will use serial */
|
|
/* SPL will load U-Boot from NAND offset 0x40000 */
|
|
#define CONFIG_SPL_NAND_DRIVERS
|
|
#define CONFIG_SPL_NAND_BASE
|
|
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x00040000
|
|
#define CONFIG_SPL_PAD_TO 0x20000
|
|
/* U-Boot will be 0x40000 bytes, loaded and run at CONFIG_SYS_TEXT_BASE */
|
|
#define CONFIG_SYS_MONITOR_LEN 0x40000 /* actually, MAX size */
|
|
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
|
|
#define CONFIG_SYS_NAND_U_BOOT_DST CONFIG_SYS_TEXT_BASE
|
|
|
|
/*
|
|
* Include SoC specific configuration
|
|
*/
|
|
#include <asm/arch/config.h>
|
|
|
|
#endif /* __CONFIG_WORK_92105_H__*/
|