u-boot/include/configs/pico-imx6ul.h
Tom Rini a09fea1d28 env: Finish migration of common ENV options
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00

166 lines
4.7 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2015 Technexion Ltd.
*
* Configuration settings for the Technexion PICO-IMX6UL-EMMC board.
*/
#ifndef __PICO_IMX6UL_CONFIG_H
#define __PICO_IMX6UL_CONFIG_H
#include <asm/arch/imx-regs.h>
#include <linux/sizes.h>
#include "mx6_common.h"
#include <asm/mach-imx/gpio.h>
#include "imx6_spl.h"
#ifdef CONFIG_SPL_OS_BOOT
/* Falcon Mode */
#define CONFIG_SPL_FS_LOAD_ARGS_NAME "args"
#define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage"
#define CONFIG_SYS_SPL_ARGS_ADDR 0x88000000
/* Falcon Mode - MMC support: args@1MB kernel@2MB */
#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x800 /* 1MB */
#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS (CONFIG_CMD_SPL_WRITE_SIZE / 512)
#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x1000 /* 2MB */
#endif
/* Network support */
#define CONFIG_FEC_MXC
#define IMX_FEC_BASE ENET2_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 0x1
#define CONFIG_FEC_XCV_TYPE RMII
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (35 * SZ_1M) /* Increase due to DFU */
#define CONFIG_MXC_UART
#define CONFIG_MXC_UART_BASE UART6_BASE_ADDR
/* MMC Configs */
#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC1_BASE_ADDR
/* USB Configs */
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS 0
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_USBD_HS
#define CONFIG_SYS_DFU_DATA_BUF_SIZE SZ_16M
#define DFU_DEFAULT_POLL_TIMEOUT 300
#define CONFIG_DFU_ENV_SETTINGS \
"dfu_alt_info=" \
"spl raw 0x2 0x400;" \
"u-boot raw 0x8a 0x400;" \
"/boot/zImage ext4 0 1;" \
"/boot/imx6ul-pico-hobbit.dtb ext4 0 1;" \
"/boot/imx6ul-pico-pi.dtb ext4 0 1;" \
"rootfs part 0 1\0" \
#define BOOTMENU_ENV \
"bootmenu_0=Boot using PICO-Dwarf baseboard=" \
"setenv fdtfile imx6ul-pico-dwarf.dtb\0" \
"bootmenu_1=Boot using PICO-Hobbit baseboard=" \
"setenv fdtfile imx6ul-pico-hobbit.dtb\0" \
"bootmenu_2=Boot using PICO-Pi baseboard=" \
"setenv fdtfile imx6ul-pico-pi.dtb\0" \
#define CONFIG_SYS_MMC_IMG_LOAD_PART 1
#define CONFIG_EXTRA_ENV_SETTINGS \
"script=boot.scr\0" \
"image=zImage\0" \
"splashpos=m,m\0" \
"console=ttymxc5\0" \
"fdt_high=0xffffffff\0" \
"initrd_high=0xffffffff\0" \
"fdtfile=" CONFIG_DEFAULT_FDT_FILE "\0" \
"videomode=video=ctfb:x:800,y:480,depth:24,mode:0,pclk:30000,le:46,ri:210,up:22,lo:23,hs:20,vs:10,sync:0,vmode:0\0" \
BOOTMENU_ENV \
"fdt_addr=0x83000000\0" \
"fdt_addr_r=0x83000000\0" \
"kernel_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
"pxefile_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
"ramdisk_addr_r=0x83000000\0" \
"ramdiskaddr=0x83000000\0" \
"scriptaddr=" __stringify(CONFIG_LOADADDR) "\0" \
"mmcautodetect=yes\0" \
CONFIG_DFU_ENV_SETTINGS \
"findfdt=" \
"if test $fdtfile = ask ; then " \
"bootmenu -1; fi;" \
"if test $fdtfile != ask ; then " \
"saveenv; fi;\0" \
"finduuid=part uuid mmc 0:1 uuid\0" \
"partitions=" \
"uuid_disk=${uuid_gpt_disk};" \
"name=rootfs,size=0,uuid=${uuid_gpt_rootfs}\0" \
"fastboot_partition_alias_system=rootfs\0" \
"setup_emmc=mmc dev 0; gpt write mmc 0 $partitions; reset;\0" \
BOOTENV
#define BOOT_TARGET_DEVICES(func) \
func(MMC, mmc, 0) \
func(USB, usb, 0) \
func(PXE, pxe, na) \
func(DHCP, dhcp, na)
#include <config_distro_bootcmd.h>
#define CONFIG_SYS_MEMTEST_START 0x80000000
#define CONFIG_SYS_MEMTEST_END CONFIG_SYS_MEMTEST_START + SZ_128M
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
#define CONFIG_SYS_HZ 1000
/* Physical Memory Map */
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
/* I2C configs */
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_SPEED 100000
/* environment organization */
/* Environment starts at 768k = 768 * 1024 = 786432 */
/*
* Detect overlap between U-Boot image and environment area in build-time
*
* CONFIG_BOARD_SIZE_LIMIT = CONFIG_ENV_OFFSET - u-boot.img offset
* CONFIG_BOARD_SIZE_LIMIT = 768k - 69k = 699k = 715776
*
* Currently CONFIG_BOARD_SIZE_LIMIT does not handle expressions, so
* write the direct value here
*/
#define CONFIG_BOARD_SIZE_LIMIT 715776
#define CONFIG_SYS_MMC_ENV_DEV 0
#define CONFIG_SYS_MMC_ENV_PART 0
#ifdef CONFIG_VIDEO
#define CONFIG_VIDEO_MXS
#define CONFIG_VIDEO_LOGO
#define CONFIG_SPLASH_SCREEN
#define CONFIG_SPLASH_SCREEN_ALIGN
#define CONFIG_BMP_16BPP
#define CONFIG_VIDEO_BMP_RLE8
#define CONFIG_VIDEO_BMP_LOGO
#define MXS_LCDIF_BASE MX6UL_LCDIF1_BASE_ADDR
#endif
#endif /* __PICO_IMX6UL_CONFIG_H */