mirror of
https://github.com/u-boot/u-boot.git
synced 2024-12-14 07:13:28 +08:00
a09fea1d28
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
91 lines
2.3 KiB
C
91 lines
2.3 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* Copyright (C) 2013 Suriyan Ramasami <suriyan.r@gmail.com>
|
|
*
|
|
* Based on dockstar.h originally written by
|
|
* Copyright (C) 2010 Eric C. Cooper <ecc@cmu.edu>
|
|
*
|
|
* Based on sheevaplug.h originally written by
|
|
* Prafulla Wadaskar <prafulla@marvell.com>
|
|
* (C) Copyright 2009
|
|
* Marvell Semiconductor <www.marvell.com>
|
|
*/
|
|
|
|
#ifndef _CONFIG_GOFLEXHOME_H
|
|
#define _CONFIG_GOFLEXHOME_H
|
|
|
|
/*
|
|
* High Level Configuration Options (easy to change)
|
|
*/
|
|
#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
|
|
#define CONFIG_KW88F6281 1 /* SOC Name */
|
|
#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
|
|
|
|
/*
|
|
* Default GPIO configuration and LED status
|
|
*/
|
|
#define GOFLEXHOME_OE_LOW (~(0))
|
|
#define GOFLEXHOME_OE_HIGH (~(0))
|
|
#define GOFLEXHOME_OE_VAL_LOW (1 << 29) /* USB_PWEN low */
|
|
#define GOFLEXHOME_OE_VAL_HIGH (1 << 17) /* LED pin high */
|
|
|
|
/* PHY related */
|
|
#define MV88E1116_LED_FCTRL_REG 10
|
|
#define MV88E1116_CPRSP_CR3_REG 21
|
|
#define MV88E1116_MAC_CTRL_REG 21
|
|
#define MV88E1116_PGADR_REG 22
|
|
#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
|
|
#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
|
|
|
|
/*
|
|
* Commands configuration
|
|
*/
|
|
|
|
/*
|
|
* mv-common.h should be defined after CMD configs since it used them
|
|
* to enable certain macros
|
|
*/
|
|
#include "mv-common.h"
|
|
|
|
/*
|
|
* Environment variables configurations
|
|
*/
|
|
/*
|
|
* max 4k env size is enough, but in case of nand
|
|
* it has to be rounded to sector size
|
|
*/
|
|
|
|
/*
|
|
* Default environment variables
|
|
*/
|
|
#define CONFIG_BOOTCOMMAND \
|
|
"setenv bootargs ${console} ${mtdparts} ${bootargs_root}; " \
|
|
"ubi part root; " \
|
|
"ubifsmount ubi:root; " \
|
|
"ubifsload 0x800000 ${kernel}; " \
|
|
"bootm 0x800000"
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"console=console=ttyS0,115200\0" \
|
|
"mtdids=nand0=orion_nand\0" \
|
|
"mtdparts="CONFIG_MTDPARTS_DEFAULT \
|
|
"kernel=/boot/uImage\0" \
|
|
"bootargs_root=ubi.mtd=root root=ubi0:root rootfstype=ubifs ro\0"
|
|
|
|
/*
|
|
* Ethernet Driver configuration
|
|
*/
|
|
#ifdef CONFIG_CMD_NET
|
|
#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
|
|
#define CONFIG_PHY_BASE_ADR 0
|
|
#endif /* CONFIG_CMD_NET */
|
|
|
|
/*
|
|
* * SATA Driver configuration
|
|
* */
|
|
#ifdef CONFIG_MVSATA_IDE
|
|
#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
|
|
#endif /*CONFIG_MVSATA_IDE*/
|
|
|
|
#endif /* _CONFIG_GOFLEXHOME_H */
|