mirror of
https://github.com/u-boot/u-boot.git
synced 2024-11-25 13:14:19 +08:00
b24f5c4f27
GPIO pins need to be set up on start-up. Add a driver to provide this, configured from the device tree. The binding is slightly different from the existing ICH6 binding, since that is quite verbose. The new binding should be just as extensible. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Bin Meng <bmeng.cn@gmail.com>
209 lines
6.7 KiB
Plaintext
209 lines
6.7 KiB
Plaintext
Intel x86 PINCTRL/GPIO controller
|
|
|
|
Pin-muxing on broadwell devices can be described with a node for the PINCTRL
|
|
master node and a set of child nodes for each required pin state on the SoC.
|
|
These pin states use phandles and are referred to but a configuration section
|
|
which lists all pins in the device.
|
|
|
|
The PINCTRL master node requires the following properties:
|
|
- compatible : "intel,x86-broadwell-pinctrl"
|
|
|
|
Pin state nodes must be sub-nodes of the pinctrl master node. The must have
|
|
a phandle. They can contain the following optional properties:
|
|
- mode-gpio - forces the pin into GPIO mode
|
|
- output-value - sets the default output value of the GPIO, 0 (low, default)
|
|
or 1 (high)
|
|
- direction - sets the direction of the gpio, either PIN_INPUT (default)
|
|
or PIN_OUTPUT
|
|
- invert - the input pin is inverted
|
|
- trigger - sets the trigger type, either TRIGGER_EDGE (default) or
|
|
TRIGGER_LEVEL
|
|
- sense-disable - the input state sense is disabled
|
|
- owner 0 sets the owner of the pin, either OWNER_ACPI (default) or
|
|
ONWER_GPIO
|
|
- route - sets whether the pin is routed, either PIRQ_APIC_MASK or
|
|
PIRQ_APIC_ROUTE
|
|
- irq-enable - the interrupt is enabled
|
|
- reset-rsmrst - the pin will only be reset by RSMRST
|
|
- pirq-apic - the pin will be routed to the IOxAPIC
|
|
|
|
The first pin state will be the default, so pins without a configuration will
|
|
use that.
|
|
|
|
The pin configuration node is also a sub-node of the pinctrl master node, but
|
|
does not have a phandle. It has a single property:
|
|
|
|
- config - configuration to use for each pin. Each entry has of 3 cells:
|
|
- GPIO number (0..94)
|
|
- phandle of configuration (above)
|
|
- interrupt number (0..15)
|
|
|
|
There should be one entry for each pin (i.e. 95 entries).
|
|
But missing pins will receive the default configuration.
|
|
|
|
Example:
|
|
|
|
pch_pinctrl {
|
|
compatible = "intel,x86-broadwell-pinctrl";
|
|
|
|
/* Put this first: it is the default */
|
|
gpio_unused: gpio-unused {
|
|
mode-gpio;
|
|
direction = <PIN_INPUT>;
|
|
owner = <OWNER_GPIO>;
|
|
sense-disable;
|
|
};
|
|
|
|
gpio_acpi_sci: acpi-sci {
|
|
mode-gpio;
|
|
direction = <PIN_INPUT>;
|
|
invert;
|
|
route = <ROUTE_SCI>;
|
|
};
|
|
|
|
gpio_acpi_smi: acpi-smi {
|
|
mode-gpio;
|
|
direction = <PIN_INPUT>;
|
|
invert;
|
|
route = <ROUTE_SMI>;
|
|
};
|
|
|
|
gpio_input: gpio-input {
|
|
mode-gpio;
|
|
direction = <PIN_INPUT>;
|
|
owner = <OWNER_GPIO>;
|
|
};
|
|
|
|
gpio_input_invert: gpio-input-invert {
|
|
mode-gpio;
|
|
direction = <PIN_INPUT>;
|
|
owner = <OWNER_GPIO>;
|
|
invert;
|
|
};
|
|
|
|
gpio_native: gpio-native {
|
|
};
|
|
|
|
gpio_out_high: gpio-out-high {
|
|
mode-gpio;
|
|
direction = <PIN_OUTPUT>;
|
|
output-value = <1>;
|
|
owner = <OWNER_GPIO>;
|
|
sense-disable;
|
|
};
|
|
|
|
gpio_out_low: gpio-out-low {
|
|
mode-gpio;
|
|
direction = <PIN_OUTPUT>;
|
|
output-value = <0>;
|
|
owner = <OWNER_GPIO>;
|
|
sense-disable;
|
|
};
|
|
|
|
gpio_pirq: gpio-pirq {
|
|
mode-gpio;
|
|
direction = <PIN_INPUT>;
|
|
owner = <OWNER_GPIO>;
|
|
pirq-apic = <PIRQ_APIC_ROUTE>;
|
|
};
|
|
|
|
soc_gpio@0 {
|
|
config =
|
|
<0 &gpio_unused 0>, /* unused */
|
|
<1 &gpio_unused 0>, /* unused */
|
|
<2 &gpio_unused 0>, /* unused */
|
|
<3 &gpio_unused 0>, /* unused */
|
|
<4 &gpio_native 0>, /* native: i2c0_sda_gpio4 */
|
|
<5 &gpio_native 0>, /* native: i2c0_scl_gpio5 */
|
|
<6 &gpio_native 0>, /* native: i2c1_sda_gpio6 */
|
|
<7 &gpio_native 0>, /* native: i2c1_scl_gpio7 */
|
|
<8 &gpio_acpi_sci 0>, /* pch_lte_wake_l */
|
|
<9 &gpio_input_invert 0>,/* trackpad_int_l (wake) */
|
|
<10 &gpio_acpi_sci 0>, /* pch_wlan_wake_l */
|
|
<11 &gpio_unused 0>, /* unused */
|
|
<12 &gpio_unused 0>, /* unused */
|
|
<13 &gpio_pirq 3>, /* trackpad_int_l (pirql) */
|
|
<14 &gpio_pirq 4>, /* touch_int_l (pirqm) */
|
|
<15 &gpio_unused 0>, /* unused (strap) */
|
|
<16 &gpio_input 0>, /* pch_wp */
|
|
<17 &gpio_unused 0>, /* unused */
|
|
<18 &gpio_unused 0>, /* unused */
|
|
<19 &gpio_unused 0>, /* unused */
|
|
<20 &gpio_native 0>, /* pcie_wlan_clkreq_l */
|
|
<21 &gpio_out_high 0>, /* pp3300_ssd_en */
|
|
<22 &gpio_unused 0>, /* unused */
|
|
<23 &gpio_out_low 0>, /* pp3300_autobahn_en */
|
|
<24 &gpio_unused 0>, /* unused */
|
|
<25 &gpio_input 0>, /* ec_in_rw */
|
|
<26 &gpio_unused 0>, /* unused */
|
|
<27 &gpio_acpi_sci 0>, /* pch_wake_l */
|
|
<28 &gpio_unused 0>, /* unused */
|
|
<29 &gpio_unused 0>, /* unused */
|
|
<30 &gpio_native 0>, /* native: pch_suswarn_l */
|
|
<31 &gpio_native 0>, /* native: acok_buf */
|
|
<32 &gpio_native 0>, /* native: lpc_clkrun_l */
|
|
<33 &gpio_native 0>, /* native: ssd_devslp */
|
|
<34 &gpio_acpi_smi 0>, /* ec_smi_l */
|
|
<35 &gpio_acpi_smi 0>, /* pch_nmi_dbg_l (route in nmi_en) */
|
|
<36 &gpio_acpi_sci 0>, /* ec_sci_l */
|
|
<37 &gpio_unused 0>, /* unused */
|
|
<38 &gpio_unused 0>, /* unused */
|
|
<39 &gpio_unused 0>, /* unused */
|
|
<40 &gpio_native 0>, /* native: pch_usb1_oc_l */
|
|
<41 &gpio_native 0>, /* native: pch_usb2_oc_l */
|
|
<42 &gpio_unused 0>, /* wlan_disable_l */
|
|
<43 &gpio_out_high 0>, /* pp1800_codec_en */
|
|
<44 &gpio_unused 0>, /* unused */
|
|
<45 &gpio_acpi_sci 0>, /* dsp_int - codec wake */
|
|
<46 &gpio_pirq 6>, /* hotword_det_l_3v3 (pirqo) - codec irq */
|
|
<47 &gpio_out_low 0>, /* ssd_reset_l */
|
|
<48 &gpio_unused 0>, /* unused */
|
|
<49 &gpio_unused 0>, /* unused */
|
|
<50 &gpio_unused 0>, /* unused */
|
|
<51 &gpio_unused 0>, /* unused */
|
|
<52 &gpio_input 0>, /* sim_det */
|
|
<53 &gpio_unused 0>, /* unused */
|
|
<54 &gpio_unused 0>, /* unused */
|
|
<55 &gpio_unused 0>, /* unused */
|
|
<56 &gpio_unused 0>, /* unused */
|
|
<57 &gpio_out_high 0>, /* codec_reset_l */
|
|
<58 &gpio_unused 0>, /* unused */
|
|
<59 &gpio_out_high 0>, /* lte_disable_l */
|
|
<60 &gpio_unused 0>, /* unused */
|
|
<61 &gpio_native 0>, /* native: pch_sus_stat */
|
|
<62 &gpio_native 0>, /* native: pch_susclk */
|
|
<63 &gpio_native 0>, /* native: pch_slp_s5_l */
|
|
<64 &gpio_unused 0>, /* unused */
|
|
<65 &gpio_input 0>, /* ram_id3 */
|
|
<66 &gpio_input 0>, /* ram_id3_old (strap) */
|
|
<67 &gpio_input 0>, /* ram_id0 */
|
|
<68 &gpio_input 0>, /* ram_id1 */
|
|
<69 &gpio_input 0>, /* ram_id2 */
|
|
<70 &gpio_unused 0>, /* unused */
|
|
<71 &gpio_native 0>, /* native: modphy_en */
|
|
<72 &gpio_unused 0>, /* unused */
|
|
<73 &gpio_unused 0>, /* unused */
|
|
<74 &gpio_unused 0>, /* unused */
|
|
<75 &gpio_unused 0>, /* unused */
|
|
<76 &gpio_unused 0>, /* unused */
|
|
<77 &gpio_unused 0>, /* unused */
|
|
<78 &gpio_unused 0>, /* unused */
|
|
<79 &gpio_unused 0>, /* unused */
|
|
<80 &gpio_unused 0>, /* unused */
|
|
<81 &gpio_unused 0>, /* unused */
|
|
<82 &gpio_native 0>, /* native: ec_rcin_l */
|
|
<83 &gpio_native 0>, /* gspi0_cs */
|
|
<84 &gpio_native 0>, /* gspi0_clk */
|
|
<85 &gpio_native 0>, /* gspi0_miso */
|
|
<86 &gpio_native 0>, /* gspi0_mosi (strap) */
|
|
<87 &gpio_unused 0>, /* unused */
|
|
<88 &gpio_unused 0>, /* unused */
|
|
<89 &gpio_out_high 0>, /* pp3300_sd_en */
|
|
<90 &gpio_unused 0>, /* unused */
|
|
<91 &gpio_unused 0>, /* unused */
|
|
<92 &gpio_unused 0>, /* unused */
|
|
<93 &gpio_unused 0>, /* unused */
|
|
<94 &gpio_unused 0 >; /* unused */
|
|
};
|
|
};
|