mirror of
https://github.com/u-boot/u-boot.git
synced 2024-12-15 15:53:26 +08:00
a13110a99f
The RK3399-Q7 SoM is a Qseven-compatible (70mm x 70mm, MXM-230 connector) system-on-module from Theobroma Systems, featuring the Rockchip RK3399. It provides the following feature set: * up to 4GB DDR3 * on-module SPI-NOR flash * on-module eMMC (with 8-bit interace) * SD card (on a baseboad) via edge connector * Gigabit Ethernet w/ on-module Micrel KSZ9031 GbE PHY * HDMI/eDP/MIPI displays * 2x MIPI-CSI * USB - 1x USB 3.0 dual-role (direct connection) - 2x USB 3.0 host + 1x USB 2.0 (on-module USB 3.0 hub) * on-module STM32 Cortex-M0 companion controller, implementing: - low-power RTC functionality (ISL1208 emulation) - fan controller (AMC6821 emulation) - USB<->CAN bridge controller Note that we use a multi-payload FIT image for booting and have Cortex-M0 payload in a separate subimage: we thus rely on the FIT image loader to put it into the SRAM region that ATF expects it in. Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com> Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Fixed build warning on puma-rk3399: Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
74 lines
1.9 KiB
Plaintext
74 lines
1.9 KiB
Plaintext
CONFIG_ARM=y
|
|
CONFIG_ARCH_ROCKCHIP=y
|
|
CONFIG_TARGET_PUMA_RK3399=y
|
|
CONFIG_SPL_LIBCOMMON_SUPPORT=y
|
|
CONFIG_SPL_LIBGENERIC_SUPPORT=y
|
|
CONFIG_SYS_MALLOC_F_LEN=0x4000
|
|
CONFIG_ROCKCHIP_RK3399=y
|
|
CONFIG_SPL_SPI_FLASH_SUPPORT=y
|
|
CONFIG_SPL_SPI_SUPPORT=y
|
|
CONFIG_SPL_STACK_R_ADDR=0x80000
|
|
CONFIG_DEFAULT_DEVICE_TREE="rk3399-puma"
|
|
CONFIG_FIT=y
|
|
CONFIG_SPL_FIT=y
|
|
CONFIG_SPL_LOAD_FIT=y
|
|
CONFIG_SPL_FIT_SOURCE="board/theobroma-systems/puma_rk3399/fit_spl_atf.its"
|
|
# CONFIG_DISPLAY_CPUINFO is not set
|
|
# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
|
|
# CONFIG_SPL_LEGACY_IMAGE_SUPPORT is not set
|
|
CONFIG_SPL_STACK_R=y
|
|
CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x4000
|
|
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x200
|
|
CONFIG_CMD_BOOTZ=y
|
|
# CONFIG_CMD_IMLS is not set
|
|
CONFIG_CMD_GPT=y
|
|
CONFIG_CMD_MMC=y
|
|
CONFIG_CMD_SF=y
|
|
CONFIG_CMD_SPI=y
|
|
CONFIG_CMD_USB=y
|
|
# CONFIG_CMD_SETEXPR is not set
|
|
CONFIG_CMD_TIME=y
|
|
CONFIG_SPL_OF_CONTROL=y
|
|
CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
|
|
CONFIG_REGMAP=y
|
|
CONFIG_SPL_REGMAP=y
|
|
CONFIG_SYSCON=y
|
|
CONFIG_SPL_SYSCON=y
|
|
CONFIG_CLK=y
|
|
CONFIG_SPL_CLK=y
|
|
CONFIG_ROCKCHIP_GPIO=y
|
|
CONFIG_MMC_DW=y
|
|
CONFIG_MMC_DW_ROCKCHIP=y
|
|
CONFIG_MMC_SDHCI=y
|
|
CONFIG_MMC_SDHCI_ROCKCHIP=y
|
|
CONFIG_SPI_FLASH=y
|
|
CONFIG_SPI_FLASH_WINBOND=y
|
|
CONFIG_PHY_MICREL=y
|
|
CONFIG_PHY_MICREL_KSZ9031=y
|
|
CONFIG_DM_ETH=y
|
|
CONFIG_ETH_DESIGNWARE=y
|
|
CONFIG_GMAC_ROCKCHIP=y
|
|
CONFIG_PINCTRL=y
|
|
CONFIG_SPL_PINCTRL=y
|
|
CONFIG_ROCKCHIP_RK3399_PINCTRL=y
|
|
CONFIG_REGULATOR_PWM=y
|
|
CONFIG_DM_REGULATOR_FIXED=y
|
|
CONFIG_PWM_ROCKCHIP=y
|
|
CONFIG_RAM=y
|
|
CONFIG_SPL_RAM=y
|
|
CONFIG_BAUDRATE=115200
|
|
CONFIG_DEBUG_UART=y
|
|
CONFIG_DEBUG_UART_BASE=0xFF180000
|
|
CONFIG_DEBUG_UART_CLOCK=24000000
|
|
CONFIG_DEBUG_UART_SHIFT=2
|
|
CONFIG_SYS_NS16550=y
|
|
CONFIG_ROCKCHIP_SPI=y
|
|
CONFIG_SYSRESET=y
|
|
CONFIG_USB=y
|
|
CONFIG_USB_XHCI_HCD=y
|
|
CONFIG_USB_XHCI_DWC3=y
|
|
CONFIG_USB_EHCI_HCD=y
|
|
CONFIG_USB_EHCI_GENERIC=y
|
|
CONFIG_USB_STORAGE=y
|
|
CONFIG_ERRNO_STR=y
|