mirror of
https://github.com/u-boot/u-boot.git
synced 2024-12-05 02:23:31 +08:00
844f9bf1ee
This patch adds a delay when regulators are disabled. This delay is set to 5 ms to cover all use cases. The worst use case actually seen is during a SD card power cycle. Signed-off-by: Christophe Kerello <christophe.kerello@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
86 lines
1.9 KiB
C
86 lines
1.9 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause */
|
|
/*
|
|
* Copyright (C) 2018, STMicroelectronics - All Rights Reserved
|
|
*/
|
|
|
|
#ifndef __PMIC_STPMU1_H_
|
|
#define __PMIC_STPMU1_H_
|
|
|
|
#define STPMU1_MASK_RESET_BUCK 0x18
|
|
#define STPMU1_BUCKX_CTRL_REG(buck) (0x20 + (buck))
|
|
#define STPMU1_VREF_CTRL_REG 0x24
|
|
#define STPMU1_LDOX_CTRL_REG(ldo) (0x25 + (ldo))
|
|
#define STPMU1_USB_CTRL_REG 0x40
|
|
#define STPMU1_NVM_USER_STATUS_REG 0xb8
|
|
#define STPMU1_NVM_USER_CONTROL_REG 0xb9
|
|
|
|
#define STPMU1_MASK_RESET_BUCK3 BIT(2)
|
|
|
|
#define STPMU1_BUCK_EN BIT(0)
|
|
#define STPMU1_BUCK_MODE BIT(1)
|
|
#define STPMU1_BUCK_OUTPUT_MASK GENMASK(7, 2)
|
|
#define STPMU1_BUCK_OUTPUT_SHIFT 2
|
|
#define STPMU1_BUCK2_1200000V (24 << STPMU1_BUCK_OUTPUT_SHIFT)
|
|
#define STPMU1_BUCK2_1350000V (30 << STPMU1_BUCK_OUTPUT_SHIFT)
|
|
#define STPMU1_BUCK3_1800000V (39 << STPMU1_BUCK_OUTPUT_SHIFT)
|
|
|
|
#define STPMU1_VREF_EN BIT(0)
|
|
|
|
#define STPMU1_LDO_EN BIT(0)
|
|
#define STPMU1_LDO12356_OUTPUT_MASK GENMASK(6, 2)
|
|
#define STPMU1_LDO12356_OUTPUT_SHIFT 2
|
|
#define STPMU1_LDO3_MODE BIT(7)
|
|
#define STPMU1_LDO3_DDR_SEL 31
|
|
#define STPMU1_LDO3_1800000 (9 << STPMU1_LDO12356_OUTPUT_SHIFT)
|
|
#define STPMU1_LDO4_UV 3300000
|
|
|
|
#define STPMU1_USB_BOOST_EN BIT(0)
|
|
#define STPMU1_USB_PWR_SW_EN GENMASK(2, 1)
|
|
|
|
#define STPMU1_NVM_USER_CONTROL_PROGRAM BIT(0)
|
|
#define STPMU1_NVM_USER_CONTROL_READ BIT(1)
|
|
|
|
#define STPMU1_NVM_USER_STATUS_BUSY BIT(0)
|
|
#define STPMU1_NVM_USER_STATUS_ERROR BIT(1)
|
|
|
|
#define STPMU1_DEFAULT_START_UP_DELAY_MS 1
|
|
#define STPMU1_DEFAULT_STOP_DELAY_MS 5
|
|
#define STPMU1_USB_BOOST_START_UP_DELAY_MS 10
|
|
|
|
enum {
|
|
STPMU1_BUCK1,
|
|
STPMU1_BUCK2,
|
|
STPMU1_BUCK3,
|
|
STPMU1_BUCK4,
|
|
STPMU1_MAX_BUCK,
|
|
};
|
|
|
|
enum {
|
|
STPMU1_BUCK_MODE_HP,
|
|
STPMU1_BUCK_MODE_LP,
|
|
};
|
|
|
|
enum {
|
|
STPMU1_LDO1,
|
|
STPMU1_LDO2,
|
|
STPMU1_LDO3,
|
|
STPMU1_LDO4,
|
|
STPMU1_LDO5,
|
|
STPMU1_LDO6,
|
|
STPMU1_MAX_LDO,
|
|
};
|
|
|
|
enum {
|
|
STPMU1_LDO_MODE_NORMAL,
|
|
STPMU1_LDO_MODE_BYPASS,
|
|
STPMU1_LDO_MODE_SINK_SOURCE,
|
|
};
|
|
|
|
enum {
|
|
STPMU1_PWR_SW1,
|
|
STPMU1_PWR_SW2,
|
|
STPMU1_MAX_PWR_SW,
|
|
};
|
|
|
|
#endif
|