mirror of
https://github.com/u-boot/u-boot.git
synced 2024-12-02 00:53:29 +08:00
970bf8603b
This converts the following to Kconfig: CONFIG_USE_BOOTCOMMAND CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND CONFIG_NFSBOOTCOMMAND Signed-off-by: Tom Rini <trini@konsulko.com>
123 lines
4.0 KiB
C
123 lines
4.0 KiB
C
/*
|
|
* GE B1x5v2
|
|
*
|
|
* Copyright 2018-2020 GE Inc.
|
|
* Copyright 2018-2020 Collabora Ltd.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#ifndef __GE_B1X5V2_CONFIG_H
|
|
#define __GE_B1X5V2_CONFIG_H
|
|
|
|
#include "mx6_common.h"
|
|
|
|
#include "imx6_spl.h"
|
|
#define CONFIG_SPL_TARGET "u-boot-with-spl.imx"
|
|
|
|
/* PWM */
|
|
#define CONFIG_IMX6_PWM_PER_CLK 66000000
|
|
|
|
/* UART */
|
|
#define CONFIG_MXC_UART_BASE UART3_BASE
|
|
|
|
#if CONFIG_MXC_UART_BASE == UART2_BASE
|
|
/* UART2 requires CONFIG_DEBUG_UART_BASE=0x21e8000 */
|
|
#define CONSOLE_DEVICE "ttymxc1" /* System on Module debug connector */
|
|
#else
|
|
/* UART3 requires CONFIG_DEBUG_UART_BASE=0x21ec000 */
|
|
#define CONSOLE_DEVICE "ttymxc2" /* Base board debug connector */
|
|
#endif
|
|
|
|
/* USB */
|
|
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
|
|
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
|
|
#define CONFIG_MXC_USB_FLAGS 0
|
|
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2 /* Enabled USB controller number */
|
|
#define CONFIG_USBD_HS
|
|
|
|
/* Video */
|
|
#define CONFIG_HIDE_LOGO_VERSION
|
|
#define CONFIG_IMX_VIDEO_SKIP
|
|
|
|
/* Memory */
|
|
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
|
|
|
|
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
|
|
#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
|
|
#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
|
|
|
|
#define CONFIG_SYS_INIT_SP_OFFSET \
|
|
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_ADDR \
|
|
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
|
|
|
|
/* Command definition */
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"image=/boot/fitImage\0" \
|
|
"fdt_addr_r=0x18000000\0" \
|
|
"splash_addr_r=0x20000000\0" \
|
|
"mmcdev=2\0" \
|
|
"mmcpart=1\0" \
|
|
"console=console="CONSOLE_DEVICE",115200\0" \
|
|
"quiet=quiet loglevel=0\0" \
|
|
"rootdev=/dev/mmcblk1p\0" \
|
|
"setargs=setenv bootargs ${console} ${quiet} ${fsckforcerepair} " \
|
|
"bootcause=${bootcause} vt.global_cursor_default=0 vt.cur_default=1 " \
|
|
"root=${rootdev}${mmcpart} video=HDMI-A-1:${resolution} rootwait ro\0" \
|
|
"loadimage=load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
|
|
"showsplashscreen=load mmc ${mmcdev}:${mmcpart} ${splash_addr_r} /boot/splashscreen-${resolution}.bmp; " \
|
|
"bmp display ${splash_addr_r};\0" \
|
|
"setconfidx=" \
|
|
"if test \"${devicetype}\" = \"B105v2\"; then " \
|
|
"setenv confidx 1; " \
|
|
"elif test \"${devicetype}\" = \"B125v2\"; then " \
|
|
"setenv confidx 2; " \
|
|
"elif test \"${devicetype}\" = \"B155v2\"; then " \
|
|
"setenv confidx 3; " \
|
|
"elif test \"${devicetype}\" = \"B105Pv2\"; then " \
|
|
"setenv confidx 4; " \
|
|
"elif test \"${devicetype}\" = \"B125Pv2\"; then " \
|
|
"setenv confidx 5; " \
|
|
"fi;\0" \
|
|
"set_default_type=setenv devicetype B155v2; setenv resolution 1366x768;" \
|
|
"setenv fdtfile imx6dl-b155v2.dtb; run setconfidx;\0" \
|
|
"checkconfidx=env exists confidx || run set_default_type;\0" \
|
|
"checkfsckforcerepair=" \
|
|
"if test \"${bootcount}\" > \"3\" ; then " \
|
|
"setenv fsckforcerepair fsck.repair=1; " \
|
|
"fi;\0" \
|
|
"helix=run setconfidx; run checkconfidx; run checkfsckforcerepair; run setargs; " \
|
|
"regulator dev LED_VCC; regulator enable; " \
|
|
"regulator dev 5V0_AUDIO; regulator enable; " \
|
|
"bootm ${loadaddr}#conf@${confidx};\0" \
|
|
"failbootcmd=" \
|
|
"echo reached failbootcmd;" \
|
|
"cls; setcurs 5 4; " \
|
|
"lcdputs \"Monitor failed to start. Try again, or contact GE Service for support.\"; " \
|
|
"bootcount reset; \0" \
|
|
"hasfirstboot=" \
|
|
"load mmc ${mmcdev}:${mmcpart} ${loadaddr} " \
|
|
"/boot/bootcause/firstboot;\0" \
|
|
"swappartitions=" \
|
|
"setexpr mmcpart 3 - ${mmcpart};\0" \
|
|
"doboot=" \
|
|
"echo Booting from mmc:${mmcdev}:${mmcpart} ...; " \
|
|
"run helix;\0" \
|
|
"altbootcmd=" \
|
|
"setenv mmcpart 1; run hasfirstboot || setenv mmcpart 2; " \
|
|
"run hasfirstboot || setenv mmcpart 0; " \
|
|
"if test ${mmcpart} != 0; then " \
|
|
"setenv bootcause REVERT; " \
|
|
"run swappartitions loadimage doboot; " \
|
|
"fi; " \
|
|
"run failbootcmd\0" \
|
|
"tryboot=" \
|
|
"setenv mmcpart 1; run hasfirstboot || setenv mmcpart 2; " \
|
|
"run loadimage || run swappartitions && run loadimage || " \
|
|
"setenv mmcpart 0 && echo MISSING IMAGE;" \
|
|
"run showsplashscreen; sleep 1; " \
|
|
"run doboot; run failbootcmd;\0" \
|
|
|
|
#endif /* __GE_B1X5V2_CONFIG_H */
|