u-boot/configs/at91sam9x5ek_mmc_defconfig
Tom Rini d31466b382 Convert CONFIG_SYS_CBSIZE to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_CBSIZE

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06 12:09:00 -04:00

75 lines
1.8 KiB
Plaintext

CONFIG_ARM=y
CONFIG_SKIP_LOWLEVEL_INIT=y
CONFIG_ARCH_AT91=y
CONFIG_SYS_TEXT_BASE=0x26f00000
CONFIG_SYS_MALLOC_LEN=0x81000
CONFIG_TARGET_AT91SAM9X5EK=y
CONFIG_ATMEL_LEGACY=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_ENV_SIZE=0x4000
CONFIG_DM_GPIO=y
CONFIG_DEFAULT_DEVICE_TREE="at91sam9g35ek"
CONFIG_DEBUG_UART_BOARD_INIT=y
CONFIG_DEBUG_UART_BASE=0xfffff200
CONFIG_DEBUG_UART_CLOCK=132000000
CONFIG_SYS_LOAD_ADDR=0x22000000
CONFIG_DEBUG_UART=y
CONFIG_FIT=y
CONFIG_SD_BOOT=y
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="mem=128M console=ttyS0,115200 mtdparts=atmel_nand:8M(bootstrap/uboot/kernel)ro,-(rootfs) root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait"
# CONFIG_CONSOLE_MUX is not set
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_HUSH_PARSER=y
CONFIG_SYS_PROMPT="U-Boot> "
CONFIG_SYS_CBSIZE=256
CONFIG_SYS_PBSIZE=281
CONFIG_CMD_BOOTZ=y
# CONFIG_CMD_FLASH is not set
CONFIG_CMD_MMC=y
CONFIG_CMD_NAND=y
CONFIG_CMD_NAND_TRIMFFS=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_BOOTP_BOOTFILESIZE=y
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
CONFIG_CMD_MTDPARTS=y
CONFIG_CMD_UBI=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_IS_IN_FAT=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_DM=y
CONFIG_CLK=y
CONFIG_CLK_AT91=y
CONFIG_AT91_GPIO=y
CONFIG_GENERIC_ATMEL_MCI=y
CONFIG_MTD=y
CONFIG_MTD_RAW_NAND=y
CONFIG_NAND_ATMEL=y
CONFIG_ATMEL_NAND_HW_PMECC=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SF_DEFAULT_SPEED=30000000
CONFIG_SPI_FLASH_ATMEL=y
CONFIG_DM_ETH=y
CONFIG_MACB=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_AT91=y
CONFIG_DM_SERIAL=y
CONFIG_DEBUG_UART_ANNOUNCE=y
CONFIG_ATMEL_USART=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
CONFIG_TIMER=y
CONFIG_ATMEL_PIT_TIMER=y
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_DM_VIDEO=y
# CONFIG_VIDEO_BPP8 is not set
# CONFIG_VIDEO_BPP32 is not set
CONFIG_ATMEL_HLCD=y