mirror of
https://github.com/u-boot/u-boot.git
synced 2024-12-27 05:33:27 +08:00
b1e8512e9d
The hummingboard2 is slightly different to the cubox i and to the hummingboard. The GPIO pin info to probe came from solidruns for of u-boot on github. https://github.com/SolidRun/u-boot-imx6/blob/imx6/board/solidrun/mx6_cubox-i/mx6_cubox-i.c#L569-L589 I have tested on a hummingboard-edge witha imx6 solo and 512mb of ram. Signed-off-by: Dennis Gilmore <dgilmore@redhat.com>
159 lines
4.6 KiB
C
159 lines
4.6 KiB
C
/*
|
|
* Copyright (C) 2015 Freescale Semiconductor, Inc.
|
|
*
|
|
* Configuration settings for the SolidRun mx6 based boards
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
#ifndef __MX6CUBOXI_CONFIG_H
|
|
#define __MX6CUBOXI_CONFIG_H
|
|
|
|
#include <config_distro_defaults.h>
|
|
#include "mx6_common.h"
|
|
|
|
#include "imx6_spl.h"
|
|
|
|
#define CONFIG_IMX_THERMAL
|
|
|
|
#define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M)
|
|
#define CONFIG_MXC_UART
|
|
|
|
/* MMC Configs */
|
|
#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC2_BASE_ADDR
|
|
|
|
/* SATA Configuration */
|
|
#ifdef CONFIG_CMD_SATA
|
|
#define CONFIG_DWC_AHSATA
|
|
#define CONFIG_SYS_SATA_MAX_DEVICE 1
|
|
#define CONFIG_DWC_AHSATA_PORT_ID 0
|
|
#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR
|
|
#define CONFIG_LBA48
|
|
#define CONFIG_LIBATA
|
|
#endif
|
|
|
|
/* Ethernet Configuration */
|
|
#define CONFIG_FEC_MXC
|
|
#define CONFIG_MII
|
|
#define IMX_FEC_BASE ENET_BASE_ADDR
|
|
#define CONFIG_FEC_XCV_TYPE RGMII
|
|
#define CONFIG_FEC_MXC_PHYADDR 0
|
|
#define CONFIG_PHY_ATHEROS
|
|
|
|
/* Framebuffer */
|
|
#define CONFIG_VIDEO_IPUV3
|
|
#define CONFIG_VIDEO_BMP_RLE8
|
|
#define CONFIG_SPLASH_SCREEN
|
|
#define CONFIG_SPLASH_SCREEN_ALIGN
|
|
#define CONFIG_BMP_16BPP
|
|
#define CONFIG_VIDEO_LOGO
|
|
#define CONFIG_VIDEO_BMP_LOGO
|
|
#define CONFIG_IMX_HDMI
|
|
#define CONFIG_IMX_VIDEO_SKIP
|
|
|
|
/* USB */
|
|
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
|
|
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
|
|
#define CONFIG_MXC_USB_FLAGS 0
|
|
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
|
|
#define CONFIG_PREBOOT \
|
|
"if hdmidet; then " \
|
|
"usb start; " \
|
|
"setenv stdin serial,usbkbd; "\
|
|
"setenv stdout serial,vga; " \
|
|
"setenv stderr serial,vga; " \
|
|
"else " \
|
|
"setenv stdin serial; " \
|
|
"setenv stdout serial; " \
|
|
"setenv stderr serial; " \
|
|
"fi;"
|
|
|
|
/* Command definition */
|
|
|
|
#define CONFIG_MXC_UART_BASE UART1_BASE
|
|
#define CONSOLE_DEV "ttymxc0"
|
|
#define CONFIG_SYS_FSL_USDHC_NUM 1
|
|
#define CONFIG_SYS_MMC_ENV_DEV 0 /* SDHC2 */
|
|
|
|
#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
|
|
#ifndef CONFIG_SPL_BUILD
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"fdtfile=undefined\0" \
|
|
"fdt_addr_r=0x18000000\0" \
|
|
"fdt_addr=0x18000000\0" \
|
|
"kernel_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
|
|
"pxefile_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
|
|
"scriptaddr=" __stringify(CONFIG_LOADADDR) "\0" \
|
|
"ramdisk_addr_r=0x13000000\0" \
|
|
"ramdiskaddr=0x13000000\0" \
|
|
"initrd_high=0xffffffff\0" \
|
|
"fdt_high=0xffffffff\0" \
|
|
"ip_dyn=yes\0" \
|
|
"console=" CONSOLE_DEV ",115200\0" \
|
|
"bootm_size=0x10000000\0" \
|
|
"mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
|
|
"finduuid=part uuid mmc 0:1 uuid\0" \
|
|
"update_sd_firmware=" \
|
|
"if test ${ip_dyn} = yes; then " \
|
|
"setenv get_cmd dhcp; " \
|
|
"else " \
|
|
"setenv get_cmd tftp; " \
|
|
"fi; " \
|
|
"if mmc dev ${mmcdev}; then " \
|
|
"if ${get_cmd} ${update_sd_firmware_filename}; then " \
|
|
"setexpr fw_sz ${filesize} / 0x200; " \
|
|
"setexpr fw_sz ${fw_sz} + 1; " \
|
|
"mmc write ${loadaddr} 0x2 ${fw_sz}; " \
|
|
"fi; " \
|
|
"fi\0" \
|
|
"findfdt="\
|
|
"if test $board_name = HUMMINGBOARD2 && test $board_rev = MX6Q ; then " \
|
|
"setenv fdtfile imx6q-hummingboard2.dtb; fi; " \
|
|
"if test $board_name = HUMMINGBOARD2 && test $board_rev = MX6DL ; then " \
|
|
"setenv fdtfile imx6dl-hummingboard2.dtb; fi; " \
|
|
"if test $board_name = HUMMINGBOARD && test $board_rev = MX6Q ; then " \
|
|
"setenv fdtfile imx6q-hummingboard.dtb; fi; " \
|
|
"if test $board_name = HUMMINGBOARD && test $board_rev = MX6DL ; then " \
|
|
"setenv fdtfile imx6dl-hummingboard.dtb; fi; " \
|
|
"if test $board_name = CUBOXI && test $board_rev = MX6Q ; then " \
|
|
"setenv fdtfile imx6q-cubox-i.dtb; fi; " \
|
|
"if test $board_name = CUBOXI && test $board_rev = MX6DL ; then " \
|
|
"setenv fdtfile imx6dl-cubox-i.dtb; fi; " \
|
|
"if test $fdtfile = undefined; then " \
|
|
"echo WARNING: Could not determine dtb to use; fi; \0" \
|
|
BOOTENV
|
|
|
|
#define CONFIG_BOOTCOMMAND \
|
|
"run findfdt; " \
|
|
"run finduuid; " \
|
|
"run distro_bootcmd"
|
|
|
|
#define BOOT_TARGET_DEVICES(func) \
|
|
func(MMC, mmc, 0) \
|
|
func(SATA, sata, 0) \
|
|
func(USB, usb, 0) \
|
|
func(PXE, pxe, na) \
|
|
func(DHCP, dhcp, na)
|
|
|
|
#include <config_distro_bootcmd.h>
|
|
|
|
#else
|
|
#define CONFIG_EXTRA_ENV_SETTINGS
|
|
#endif /* CONFIG_SPL_BUILD */
|
|
|
|
/* Physical Memory Map */
|
|
#define CONFIG_NR_DRAM_BANKS 1
|
|
#define CONFIG_SYS_SDRAM_BASE MMDC0_ARB_BASE_ADDR
|
|
#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
|
|
#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
|
|
|
|
#define CONFIG_SYS_INIT_SP_OFFSET \
|
|
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_ADDR \
|
|
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
|
|
|
|
/* Environment organization */
|
|
#define CONFIG_ENV_SIZE (8 * 1024)
|
|
#define CONFIG_ENV_OFFSET (8 * 64 * 1024)
|
|
|
|
#endif /* __MX6CUBOXI_CONFIG_H */
|