u-boot/include/configs/korat.h
Tom Rini c2120fbfbc Merge branch 'master' of git://git.denx.de/u-boot-i2c
The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.

Conflicts:
	board/sandburst/common/ppc440gx_i2c.c
	board/sandburst/common/ppc440gx_i2c.h

Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:50:24 -04:00

556 lines
22 KiB
C

/*
* (C) Copyright 2007-2009
* Larry Johnson, lrj@acm.org
*
* (C) Copyright 2006-2007
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
* (C) Copyright 2006
* Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com
* Alain Saurel, AMCC/IBM, alain.saurel@fr.ibm.com
*
* SPDX-License-Identifier: GPL-2.0+
*/
/*
* korat.h - configuration for Korat board
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
*/
#define CONFIG_440EPX 1 /* Specific PPC440EPx */
#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_SYS_CLK_FREQ 33333333
#ifdef CONFIG_KORAT_PERMANENT
#define CONFIG_SYS_TEXT_BASE 0xFFFA0000
#else
#define CONFIG_SYS_TEXT_BASE 0xF7F60000
#endif
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
/*
* Manufacturer's information serial EEPROM parameters
*/
#define MAN_DATA_EEPROM_ADDR 0x53 /* EEPROM I2C address */
#define MAN_INFO_FIELD 2
#define MAN_INFO_LENGTH 9
#define MAN_MAC_ADDR_FIELD 3
#define MAN_MAC_ADDR_LENGTH 12
/*
* Base addresses -- Note these are effective addresses where the actual
* resources get mapped (not physical addresses).
*/
#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kiB for Monitor */
#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserve 256 kiB for malloc() */
#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */
#define CONFIG_SYS_FLASH0_SIZE 0x01000000
#define CONFIG_SYS_FLASH0_ADDR (-CONFIG_SYS_FLASH0_SIZE)
#define CONFIG_SYS_FLASH1_TOP 0xF8000000
#define CONFIG_SYS_FLASH1_MAX_SIZE 0x08000000
#define CONFIG_SYS_FLASH1_ADDR (CONFIG_SYS_FLASH1_TOP - CONFIG_SYS_FLASH1_MAX_SIZE)
#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH1_ADDR /* start of FLASH */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_OCM_BASE 0xe0010000 /* ocm */
#define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_OCM_BASE
#define CONFIG_SYS_PCI_BASE 0xe0000000 /* Internal PCI regs */
#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */
#define CONFIG_SYS_PCI_MEMBASE2 (CONFIG_SYS_PCI_MEMBASE + 0x20000000)
#define CONFIG_SYS_USB2D0_BASE 0xe0000100
#define CONFIG_SYS_USB_DEVICE 0xe0000000
#define CONFIG_SYS_USB_HOST 0xe0000400
#define CONFIG_SYS_CPLD_BASE 0xc0000000
/*
* Initial RAM & stack pointer
*/
/* 440EPx has 16KB of internal SRAM, so no need for D-Cache */
#undef CONFIG_SYS_INIT_RAM_DCACHE
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_BASE /* OCM */
#define CONFIG_SYS_INIT_RAM_SIZE (4 << 10)
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
/*
* Serial Port
*/
#define CONFIG_CONS_INDEX 1 /* Use UART0 */
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_serial_clock()
#define CONFIG_SYS_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
/*
* Environment
*/
#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environ vars */
/*
* FLASH related
*/
#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
#define CONFIG_FLASH_CFI_LEGACY /* Allow hard-coded config for FLASH0 */
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH1_ADDR, CONFIG_SYS_FLASH0_ADDR }
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* max number of sectors on one chip */
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware flash protection */
#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH1_TOP - CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
/* Address and size of Redundant Environment Sector */
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
/*
* DDR SDRAM
*/
#define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */
#define CONFIG_ZERO_SDRAM /* Zero SDRAM after setup */
#define CONFIG_DDR_ECC /* Use ECC when available */
#define SPD_EEPROM_ADDRESS {0x50}
#define CONFIG_PROG_SDRAM_TLB
#define CONFIG_SYS_MEM_TOP_HIDE (4 << 10) /* don't use last 4 KiB as */
/* per 440EPx Errata CHIP_11 */
/*
* I2C
*/
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_PPC4XX
#define CONFIG_SYS_I2C_PPC4XX_CH0
#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F
#define CONFIG_SYS_I2C_MULTI_EEPROMS
#define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1)
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
/* I2C RTC */
#define CONFIG_RTC_M41T60 1
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
/* I2C SYSMON (LM73) */
#define CONFIG_DTT_LM73 1 /* National Semi's LM73 */
#define CONFIG_DTT_SENSORS {2} /* Sensor addresses */
#define CONFIG_SYS_DTT_MAX_TEMP 70
#define CONFIG_SYS_DTT_MIN_TEMP -30
#define CONFIG_PREBOOT "echo;" \
"echo Type \\\"run flash_cf\\\" to mount from CompactFlash(R);" \
"echo"
#undef CONFIG_BOOTARGS
/* Setup some board specific values for the default environment variables */
#define CONFIG_HOSTNAME korat
/* Note: kernel_addr and ramdisk_addr assume that FLASH1 is 64 MiB. */
#define CONFIG_EXTRA_ENV_SETTINGS \
"u_boot=korat/u-boot.bin\0" \
"load=tftp 200000 ${u_boot}\0" \
"update=protect off F7F60000 F7FBFFFF;erase F7F60000 F7FBFFFF;" \
"cp.b ${fileaddr} F7F60000 ${filesize};protect on " \
"F7F60000 F7FBFFFF\0" \
"upd=run load update\0" \
"bootfile=korat/uImage\0" \
"dtb=korat/korat.dtb\0" \
"kernel_addr=F4000000\0" \
"ramdisk_addr=F4400000\0" \
"dtb_addr=F41E0000\0" \
"udl=tftp 200000 ${bootfile}; erase F4000000 F41DFFFF; " \
"cp.b ${fileaddr} F4000000 ${filesize}\0" \
"udd=tftp 200000 ${dtb}; erase F41E0000 F41FFFFF; " \
"cp.b ${fileaddr} F41E0000 ${filesize}\0" \
"ll=setenv kernel_addr 200000; setenv dtb_addr 1000000; " \
"tftp ${kernel_addr} ${uImage}; tftp ${dtb_addr} " \
"${dtb}\0" \
"rd_size=73728\0" \
"ramargs=setenv bootargs root=/dev/ram rw " \
"ramdisk_size=${rd_size}\0" \
"usbdev=sda1\0" \
"usbargs=setenv bootargs root=/dev/${usbdev} ro rootdelay=10\0" \
"rootpath=/opt/eldk/ppc_4xxFP\0" \
"netdev=eth0\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=${serverip}:${rootpath}\0" \
"pciclk=33\0" \
"addide=setenv bootargs ${bootargs} ide=reverse " \
"idebus=${pciclk}\0" \
"addip=setenv bootargs ${bootargs} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
":${hostname}:${netdev}:off panic=1\0" \
"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
"flash_cf=run usbargs addide addip addtty; " \
"bootm ${kernel_addr} - ${dtb_addr}\0" \
"flash_nfs=run nfsargs addide addip addtty; " \
"bootm ${kernel_addr} - ${dtb_addr}\0" \
"flash_self=run ramargs addip addtty; " \
"bootm ${kernel_addr} ${ramdisk_addr} ${dtb_addr}\0" \
""
#define CONFIG_BOOTCOMMAND "run flash_cf"
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_PPC4xx_EMAC
#define CONFIG_IBM_EMAC4_V4 1
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 2 /* PHY address, See schematics */
#define CONFIG_PHY_DYNAMIC_ANEG 1
#undef CONFIG_PHY_RESET /* Don't do software PHY reset */
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
#define CONFIG_HAS_ETH0
#define CONFIG_SYS_RX_ETH_BUFFER 32 /* Number of ethernet rx */
/* buffers & descriptors */
#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
#define CONFIG_PHY1_ADDR 3
/* USB */
#define CONFIG_USB_OHCI
#define CONFIG_USB_STORAGE
/* Comment this out to enable USB 1.1 device */
#define USB_2_0_DEVICE
/* Partitions */
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
#define CONFIG_ISO_PARTITION
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
#define CONFIG_BOOTP_SUBNETMASK
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DATE
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_DTT
#define CONFIG_CMD_DIAG
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_ELF
#define CONFIG_CMD_FAT
#define CONFIG_CMD_I2C
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_MII
#define CONFIG_CMD_NET
#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
#define CONFIG_CMD_PING
#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_USB
/* POST support */
#define CONFIG_POST (CONFIG_SYS_POST_CACHE | \
CONFIG_SYS_POST_CPU | \
CONFIG_SYS_POST_ECC | \
CONFIG_SYS_POST_ETHER | \
CONFIG_SYS_POST_FPU | \
CONFIG_SYS_POST_I2C | \
CONFIG_SYS_POST_MEMORY | \
CONFIG_SYS_POST_RTC | \
CONFIG_SYS_POST_SPR | \
CONFIG_SYS_POST_UART)
#define CONFIG_LOGBUFFER
#define CONFIG_SYS_POST_CACHE_ADDR 0xC8000000 /* free virtual address */
#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
#define CONFIG_SUPPORT_VFAT
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
/* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_LOOPW 1 /* enable loopw command */
#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
/*
* Korat-specific options
*/
#define CONFIG_SYS_KORAT_MAN_RESET_MS 10000 /* timeout for manufacturer reset */
/*
* PCI stuff
*/
/* General PCI */
#define CONFIG_PCI /* include pci support */
#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_SYS_PCI_CACHE_LINE_SIZE 0 /* to avoid problems with PNP */
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to */
/* CONFIG_SYS_PCI_MEMBASE */
/* Board-specific PCI */
#define CONFIG_SYS_PCI_TARGET_INIT
#define CONFIG_SYS_PCI_MASTER_INIT
#define CONFIG_SYS_PCI_BOARD_FIXUP_IRQ
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
#define CONFIG_SYS_PCI_SUBSYS_ID 0xcafe /* Whatever */
/*
* For booting Linux, the board info and command line data have to be in the
* first 8 MB of memory, since this is the maximum mapped by the Linux kernel
* during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*
* External Bus Controller (EBC) Setup
*/
/* Memory Bank 0 (NOR-FLASH) initialization */
#if CONFIG_SYS_FLASH0_SIZE == 0x01000000
#define CONFIG_SYS_EBC_PB0AP 0x04017300
#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH0_ADDR | 0x0009A000)
#elif CONFIG_SYS_FLASH0_SIZE == 0x04000000
#define CONFIG_SYS_EBC_PB0AP 0x04017300
#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH0_ADDR | 0x000DA000)
#else
#error Unable to configure chip select for current CONFIG_SYS_FLASH0_SIZE
#endif
/* Memory Bank 1 (NOR-FLASH) initialization */
#if CONFIG_SYS_FLASH1_MAX_SIZE == 0x08000000
#define CONFIG_SYS_EBC_PB1AP 0x04017300
#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_FLASH1_ADDR | 0x000FA000)
#else
#error Unable to configure chip select for current CONFIG_SYS_FLASH1_MAX_SIZE
#endif
/* Memory Bank 2 (CPLD) initialization */
#define CONFIG_SYS_EBC_PB2AP 0x04017300
#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_CPLD_BASE | 0x00038000)
/*
* GPIO Setup
*
* Korat GPIO usage:
*
* Init.
* Pin Source I/O value Function
* ------ ------ --- ----- ---------------------------------
* GPIO00 Alt1 I/O x PerAddr07
* GPIO01 Alt1 I/O x PerAddr06
* GPIO02 Alt1 I/O x PerAddr05
* GPIO03 GPIO x x GPIO03 to expansion bus connector
* GPIO04 GPIO x x GPIO04 to expansion bus connector
* GPIO05 GPIO x x GPIO05 to expansion bus connector
* GPIO06 Alt1 O x PerCS1 (2nd NOR flash)
* GPIO07 Alt1 O x PerCS2 (CPLD)
* GPIO08 Alt1 O x PerCS3 to expansion bus connector
* GPIO09 Alt1 O x PerCS4 to expansion bus connector
* GPIO10 Alt1 O x PerCS5 to expansion bus connector
* GPIO11 Alt1 I x PerErr
* GPIO12 GPIO O 0 ATMega !Reset
* GPIO13 GPIO x x Test Point 2 (TP2)
* GPIO14 GPIO O 1 Write protect EEPROM #1 (0xA8)
* GPIO15 GPIO O 0 CPU Run LED !On
* GPIO16 Alt1 O x GMC1TxD0
* GPIO17 Alt1 O x GMC1TxD1
* GPIO18 Alt1 O x GMC1TxD2
* GPIO19 Alt1 O x GMC1TxD3
* GPIO20 Alt1 I x RejectPkt0
* GPIO21 Alt1 I x RejectPkt1
* GPIO22 GPIO I x PGOOD_DDR
* GPIO23 Alt1 O x SCPD0
* GPIO24 Alt1 O x GMC0TxD2
* GPIO25 Alt1 O x GMC0TxD3
* GPIO26 GPIO? I/O x IIC0SDA (selected in SDR0_PFC4)
* GPIO27 GPIO O 0 PHY #0 1000BASE-X select
* GPIO28 GPIO O 0 PHY #1 1000BASE-X select
* GPIO29 GPIO I x Test jumper !Present
* GPIO30 GPIO I x SFP module #0 !Present
* GPIO31 GPIO I x SFP module #1 !Present
*
* GPIO32 GPIO O 1 SFP module #0 Tx !Enable
* GPIO33 GPIO O 1 SFP module #1 Tx !Enable
* GPIO34 Alt2 I x !UART1_CTS
* GPIO35 Alt2 O x !UART1_RTS
* GPIO36 Alt1 I x !UART0_CTS
* GPIO37 Alt1 O x !UART0_RTS
* GPIO38 Alt2 O x UART1_Tx
* GPIO39 Alt2 I x UART1_Rx
* GPIO40 Alt1 I x IRQ0 (Ethernet 0)
* GPIO41 Alt1 I x IRQ1 (Ethernet 1)
* GPIO42 Alt1 I x IRQ2 (PCI interrupt)
* GPIO43 Alt1 I x IRQ3 (System Alert from CPLD)
* GPIO44 xxxx x x (grounded through pulldown)
* GPIO45 GPIO O 0 PHY #0 Enable
* GPIO46 GPIO O 0 PHY #1 Enable
* GPIO47 GPIO I x Reset switch !Pressed
* GPIO48 GPIO I x Shutdown switch !Pressed
* GPIO49 xxxx x x (reserved for trace port)
* . . . . .
* . . . . .
* . . . . .
* GPIO63 xxxx x x (reserved for trace port)
*/
#define CONFIG_SYS_GPIO_ATMEGA_RESET_ 12
#define CONFIG_SYS_GPIO_ATMEGA_SS_ 13
#define CONFIG_SYS_GPIO_PHY0_FIBER_SEL 27
#define CONFIG_SYS_GPIO_PHY1_FIBER_SEL 28
#define CONFIG_SYS_GPIO_SFP0_PRESENT_ 30
#define CONFIG_SYS_GPIO_SFP1_PRESENT_ 31
#define CONFIG_SYS_GPIO_SFP0_TX_EN_ 32
#define CONFIG_SYS_GPIO_SFP1_TX_EN_ 33
#define CONFIG_SYS_GPIO_PHY0_EN 45
#define CONFIG_SYS_GPIO_PHY1_EN 46
#define CONFIG_SYS_GPIO_RESET_PRESSED_ 47
/*
* PPC440 GPIO Configuration
*/
#define CONFIG_SYS_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \
{ \
/* GPIO Core 0 */ \
{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO0 EBC_ADDR(7) DMA_REQ(2) */ \
{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO1 EBC_ADDR(6) DMA_ACK(2) */ \
{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO2 EBC_ADDR(5) DMA_EOT/TC(2) */ \
{GPIO0_BASE, GPIO_DIS, GPIO_SEL , GPIO_OUT_0}, /* GPIO3 EBC_ADDR(4) DMA_REQ(3) */ \
{GPIO0_BASE, GPIO_DIS, GPIO_SEL , GPIO_OUT_0}, /* GPIO4 EBC_ADDR(3) DMA_ACK(3) */ \
{GPIO0_BASE, GPIO_DIS, GPIO_SEL , GPIO_OUT_0}, /* GPIO5 EBC_ADDR(2) DMA_EOT/TC(3) */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO6 EBC_CS_N(1) */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO7 EBC_CS_N(2) */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 EBC_CS_N(3) */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 EBC_CS_N(4) */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 EBC_CS_N(5) */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO11 EBC_BUS_ERR */ \
{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO12 */ \
{GPIO0_BASE, GPIO_DIS, GPIO_SEL , GPIO_OUT_0}, /* GPIO13 */ \
{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO14 */ \
{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO15 */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO16 GMCTxD(4) */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO17 GMCTxD(5) */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO18 GMCTxD(6) */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO19 GMCTxD(7) */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO20 RejectPkt0 */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO21 RejectPkt1 */ \
{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO22 */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO23 SCPD0 */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO24 GMCTxD(2) */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO25 GMCTxD(3) */ \
{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO26 */ \
{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO27 EXT_EBC_REQ USB2D_RXERROR */ \
{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO28 USB2D_TXVALID */ \
{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO29 EBC_EXT_HDLA USB2D_PAD_SUSPNDM */ \
{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO30 EBC_EXT_ACK USB2D_XCVRSELECT*/ \
{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO31 EBC_EXR_BUSREQ USB2D_TERMSELECT*/ \
}, \
{ \
/* GPIO Core 1 */ \
{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO32 USB2D_OPMODE0 EBC_DATA(2) */ \
{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO33 USB2D_OPMODE1 EBC_DATA(3) */ \
{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO34 UART0_DCD_N UART1_DSR_CTS_N UART2_SOUT*/ \
{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO35 UART0_8PIN_DSR_N UART1_RTS_DTR_N UART2_SIN*/ \
{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO36 UART0_8PIN_CTS_N EBC_DATA(0) UART3_SIN*/ \
{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO37 UART0_RTS_N EBC_DATA(1) UART3_SOUT*/ \
{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO38 UART0_DTR_N UART1_SOUT */ \
{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO39 UART0_RI_N UART1_SIN */ \
{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO40 UIC_IRQ(0) */ \
{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO41 UIC_IRQ(1) */ \
{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO42 UIC_IRQ(2) */ \
{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO43 UIC_IRQ(3) */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO44 UIC_IRQ(4) DMA_ACK(1) */ \
{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO45 UIC_IRQ(6) DMA_EOT/TC(1) */ \
{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO46 UIC_IRQ(7) DMA_REQ(0) */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO47 UIC_IRQ(8) DMA_ACK(0) */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO48 UIC_IRQ(9) DMA_EOT/TC(0) */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO49 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO50 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO51 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO52 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO53 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO54 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO55 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO56 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO57 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO58 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO59 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO60 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO61 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO62 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO63 Unselect via TraceSelect Bit */ \
} \
}
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
/* Pass open firmware flat tree */
#define CONFIG_OF_LIBFDT 1
#define CONFIG_OF_BOARD_SETUP 1
#endif /* __CONFIG_H */