mirror of
https://github.com/u-boot/u-boot.git
synced 2024-12-01 00:23:29 +08:00
b5ee48c099
This patch adds support for more PMBus compatible devices to the NXP drivers for its QorIQ family devices. At runtime, the voltage regulator is queried over I2C, and the required voltage multiplier determined. This change supports the DIRECT and LINEAR PMBus voltage reporting modes. Previously, the driver only supported a few specific devices such as the IR36021 and LTC3882, so this change allows the QorIQ series to be used with a much larger variety of core voltage regulator devices. checkpatch warning "Use if (IS_DEFINED (...))" was ignored to maintain consistency with the existing code. Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com> Signed-off-by: Wasim Khan <wasim.khan@nxp.com> Tested-by: Wasim Khan <wasim.khan@nxp.com> [Rebased] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
576 lines
19 KiB
C
576 lines
19 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* Copyright 2017, 2020 NXP
|
|
*/
|
|
|
|
#ifndef __LS1088A_QDS_H
|
|
#define __LS1088A_QDS_H
|
|
|
|
#include "ls1088a_common.h"
|
|
|
|
|
|
#ifndef __ASSEMBLY__
|
|
unsigned long get_board_sys_clk(void);
|
|
unsigned long get_board_ddr_clk(void);
|
|
#endif
|
|
|
|
#ifdef CONFIG_TFABOOT
|
|
#define CONFIG_MISC_INIT_R
|
|
#endif
|
|
|
|
#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
|
|
#define CONFIG_QIXIS_I2C_ACCESS
|
|
#define SYS_NO_FLASH
|
|
|
|
#define CONFIG_SYS_CLK_FREQ 100000000
|
|
#define CONFIG_DDR_CLK_FREQ 100000000
|
|
#else
|
|
#define CONFIG_QIXIS_I2C_ACCESS
|
|
#if !CONFIG_IS_ENABLED(DM_I2C)
|
|
#define CONFIG_SYS_I2C_EARLY_INIT
|
|
#endif
|
|
#define CONFIG_SYS_CLK_FREQ get_board_sys_clk()
|
|
#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk()
|
|
#endif
|
|
|
|
#define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ/4)
|
|
#define COUNTER_FREQUENCY 25000000 /* 25MHz */
|
|
|
|
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
|
|
|
|
#define CONFIG_DDR_SPD
|
|
#define CONFIG_DDR_ECC
|
|
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
|
|
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
|
|
#define SPD_EEPROM_ADDRESS 0x51
|
|
#define CONFIG_SYS_SPD_BUS_NUM 0
|
|
|
|
|
|
/*
|
|
* IFC Definitions
|
|
*/
|
|
#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
|
|
#define CONFIG_SYS_NOR0_CSPR_EXT (0x0)
|
|
#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
|
|
#define CONFIG_SYS_NOR_AMASK_EARLY IFC_AMASK(64*1024*1024)
|
|
|
|
#define CONFIG_SYS_NOR0_CSPR \
|
|
(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
|
|
CSPR_PORT_SIZE_16 | \
|
|
CSPR_MSEL_NOR | \
|
|
CSPR_V)
|
|
#define CONFIG_SYS_NOR0_CSPR_EARLY \
|
|
(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY) | \
|
|
CSPR_PORT_SIZE_16 | \
|
|
CSPR_MSEL_NOR | \
|
|
CSPR_V)
|
|
#define CONFIG_SYS_NOR1_CSPR \
|
|
(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH1_BASE_PHYS) | \
|
|
CSPR_PORT_SIZE_16 | \
|
|
CSPR_MSEL_NOR | \
|
|
CSPR_V)
|
|
#define CONFIG_SYS_NOR1_CSPR_EARLY \
|
|
(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH1_BASE_PHYS_EARLY) | \
|
|
CSPR_PORT_SIZE_16 | \
|
|
CSPR_MSEL_NOR | \
|
|
CSPR_V)
|
|
#define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(12)
|
|
#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \
|
|
FTIM0_NOR_TEADC(0x5) | \
|
|
FTIM0_NOR_TAVDS(0x6) | \
|
|
FTIM0_NOR_TEAHC(0x5))
|
|
#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \
|
|
FTIM1_NOR_TRAD_NOR(0x1a) | \
|
|
FTIM1_NOR_TSEQRAD_NOR(0x13))
|
|
#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x8) | \
|
|
FTIM2_NOR_TCH(0x8) | \
|
|
FTIM2_NOR_TWPH(0xe) | \
|
|
FTIM2_NOR_TWP(0x1c))
|
|
#define CONFIG_SYS_NOR_FTIM3 0x04000000
|
|
#define CONFIG_SYS_IFC_CCR 0x01000000
|
|
|
|
#ifndef SYS_NO_FLASH
|
|
#define CONFIG_SYS_FLASH_QUIET_TEST
|
|
#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
|
|
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
|
|
|
|
#define CONFIG_SYS_FLASH_EMPTY_INFO
|
|
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE,\
|
|
CONFIG_SYS_FLASH_BASE + 0x40000000}
|
|
#endif
|
|
#endif
|
|
|
|
#define CONFIG_NAND_FSL_IFC
|
|
#define CONFIG_SYS_NAND_MAX_ECCPOS 256
|
|
#define CONFIG_SYS_NAND_MAX_OOBFREE 2
|
|
|
|
#define CONFIG_SYS_NAND_CSPR_EXT (0x0)
|
|
#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
|
|
| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
|
|
| CSPR_MSEL_NAND /* MSEL = NAND */ \
|
|
| CSPR_V)
|
|
#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024)
|
|
|
|
#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
|
|
| CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
|
|
| CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
|
|
| CSOR_NAND_RAL_3 /* RAL = 3Byes */ \
|
|
| CSOR_NAND_PGS_2K /* Page Size = 2K */ \
|
|
| CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
|
|
| CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
|
|
|
|
#define CONFIG_SYS_NAND_ONFI_DETECTION
|
|
|
|
/* ONFI NAND Flash mode0 Timing Params */
|
|
#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
|
|
FTIM0_NAND_TWP(0x18) | \
|
|
FTIM0_NAND_TWCHT(0x07) | \
|
|
FTIM0_NAND_TWH(0x0a))
|
|
#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
|
|
FTIM1_NAND_TWBE(0x39) | \
|
|
FTIM1_NAND_TRR(0x0e) | \
|
|
FTIM1_NAND_TRP(0x18))
|
|
#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \
|
|
FTIM2_NAND_TREH(0x0a) | \
|
|
FTIM2_NAND_TWHRE(0x1e))
|
|
#define CONFIG_SYS_NAND_FTIM3 0x0
|
|
|
|
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
|
|
#define CONFIG_SYS_MAX_NAND_DEVICE 1
|
|
#define CONFIG_MTD_NAND_VERIFY_WRITE
|
|
|
|
#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
|
|
|
|
#define CONFIG_FSL_QIXIS
|
|
#define CONFIG_SYS_I2C_FPGA_ADDR 0x66
|
|
#define QIXIS_LBMAP_SWITCH 6
|
|
#define QIXIS_QMAP_MASK 0xe0
|
|
#define QIXIS_QMAP_SHIFT 5
|
|
#define QIXIS_LBMAP_MASK 0x0f
|
|
#define QIXIS_LBMAP_SHIFT 0
|
|
#define QIXIS_LBMAP_DFLTBANK 0x0e
|
|
#define QIXIS_LBMAP_ALTBANK 0x2e
|
|
#define QIXIS_LBMAP_SD 0x00
|
|
#define QIXIS_LBMAP_EMMC 0x00
|
|
#define QIXIS_LBMAP_IFC 0x00
|
|
#define QIXIS_LBMAP_SD_QSPI 0x0e
|
|
#define QIXIS_LBMAP_QSPI 0x0e
|
|
#define QIXIS_RCW_SRC_IFC 0x25
|
|
#define QIXIS_RCW_SRC_SD 0x40
|
|
#define QIXIS_RCW_SRC_EMMC 0x41
|
|
#define QIXIS_RCW_SRC_QSPI 0x62
|
|
#define QIXIS_RST_CTL_RESET 0x41
|
|
#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
|
|
#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
|
|
#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
|
|
#define QIXIS_RST_FORCE_MEM 0x01
|
|
#define QIXIS_STAT_PRES1 0xb
|
|
#define QIXIS_SDID_MASK 0x07
|
|
#define QIXIS_ESDHC_NO_ADAPTER 0x7
|
|
|
|
#define CONFIG_SYS_FPGA_CSPR_EXT (0x0)
|
|
#define CONFIG_SYS_FPGA_CSPR (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \
|
|
| CSPR_PORT_SIZE_8 \
|
|
| CSPR_MSEL_GPCM \
|
|
| CSPR_V)
|
|
#define SYS_FPGA_CSPR_FINAL (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
|
|
| CSPR_PORT_SIZE_8 \
|
|
| CSPR_MSEL_GPCM \
|
|
| CSPR_V)
|
|
|
|
#define SYS_FPGA_AMASK IFC_AMASK(64 * 1024)
|
|
#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
|
|
#define CONFIG_SYS_FPGA_CSOR CSOR_GPCM_ADM_SHIFT(0)
|
|
#else
|
|
#define CONFIG_SYS_FPGA_CSOR CSOR_GPCM_ADM_SHIFT(12)
|
|
#endif
|
|
/* QIXIS Timing parameters*/
|
|
#define SYS_FPGA_CS_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \
|
|
FTIM0_GPCM_TEADC(0x0e) | \
|
|
FTIM0_GPCM_TEAHC(0x0e))
|
|
#define SYS_FPGA_CS_FTIM1 (FTIM1_GPCM_TACO(0xff) | \
|
|
FTIM1_GPCM_TRAD(0x3f))
|
|
#define SYS_FPGA_CS_FTIM2 (FTIM2_GPCM_TCS(0xf) | \
|
|
FTIM2_GPCM_TCH(0xf) | \
|
|
FTIM2_GPCM_TWP(0x3E))
|
|
#define SYS_FPGA_CS_FTIM3 0x0
|
|
|
|
#ifdef CONFIG_TFABOOT
|
|
#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
|
|
#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR_EARLY
|
|
#define CONFIG_SYS_CSPR0_FINAL CONFIG_SYS_NOR0_CSPR
|
|
#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
|
|
#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
|
|
#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
|
|
#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
|
|
#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
|
|
#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
|
|
#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT
|
|
#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR_EARLY
|
|
#define CONFIG_SYS_CSPR1_FINAL CONFIG_SYS_NOR1_CSPR
|
|
#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK_EARLY
|
|
#define CONFIG_SYS_AMASK1_FINAL CONFIG_SYS_NOR_AMASK
|
|
#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
|
|
#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
|
|
#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
|
|
#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
|
|
#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
|
|
#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT
|
|
#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR
|
|
#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK
|
|
#define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR
|
|
#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0
|
|
#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1
|
|
#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2
|
|
#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3
|
|
#define CONFIG_SYS_CSPR3_EXT CONFIG_SYS_FPGA_CSPR_EXT
|
|
#define CONFIG_SYS_CSPR3 CONFIG_SYS_FPGA_CSPR
|
|
#define CONFIG_SYS_CSPR3_FINAL SYS_FPGA_CSPR_FINAL
|
|
#define CONFIG_SYS_AMASK3 SYS_FPGA_AMASK
|
|
#define CONFIG_SYS_CSOR3 CONFIG_SYS_FPGA_CSOR
|
|
#define CONFIG_SYS_CS3_FTIM0 SYS_FPGA_CS_FTIM0
|
|
#define CONFIG_SYS_CS3_FTIM1 SYS_FPGA_CS_FTIM1
|
|
#define CONFIG_SYS_CS3_FTIM2 SYS_FPGA_CS_FTIM2
|
|
#define CONFIG_SYS_CS3_FTIM3 SYS_FPGA_CS_FTIM3
|
|
#else
|
|
#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
|
|
#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
|
|
#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
|
|
#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
|
|
#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
|
|
#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
|
|
#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
|
|
#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
|
|
#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
|
|
#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_FPGA_CSPR_EXT
|
|
#define CONFIG_SYS_CSPR2 CONFIG_SYS_FPGA_CSPR
|
|
#define CONFIG_SYS_CSPR2_FINAL SYS_FPGA_CSPR_FINAL
|
|
#define CONFIG_SYS_AMASK2 SYS_FPGA_AMASK
|
|
#define CONFIG_SYS_CSOR2 CONFIG_SYS_FPGA_CSOR
|
|
#define CONFIG_SYS_CS2_FTIM0 SYS_FPGA_CS_FTIM0
|
|
#define CONFIG_SYS_CS2_FTIM1 SYS_FPGA_CS_FTIM1
|
|
#define CONFIG_SYS_CS2_FTIM2 SYS_FPGA_CS_FTIM2
|
|
#define CONFIG_SYS_CS2_FTIM3 SYS_FPGA_CS_FTIM3
|
|
#else
|
|
#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
|
|
#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR_EARLY
|
|
#define CONFIG_SYS_CSPR0_FINAL CONFIG_SYS_NOR0_CSPR
|
|
#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
|
|
#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
|
|
#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
|
|
#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
|
|
#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
|
|
#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
|
|
#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT
|
|
#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR_EARLY
|
|
#define CONFIG_SYS_CSPR1_FINAL CONFIG_SYS_NOR1_CSPR
|
|
#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK_EARLY
|
|
#define CONFIG_SYS_AMASK1_FINAL CONFIG_SYS_NOR_AMASK
|
|
#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
|
|
#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
|
|
#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
|
|
#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
|
|
#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
|
|
#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT
|
|
#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR
|
|
#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK
|
|
#define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR
|
|
#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0
|
|
#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1
|
|
#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2
|
|
#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3
|
|
#define CONFIG_SYS_CSPR3_EXT CONFIG_SYS_FPGA_CSPR_EXT
|
|
#define CONFIG_SYS_CSPR3 CONFIG_SYS_FPGA_CSPR
|
|
#define CONFIG_SYS_CSPR3_FINAL SYS_FPGA_CSPR_FINAL
|
|
#define CONFIG_SYS_AMASK3 SYS_FPGA_AMASK
|
|
#define CONFIG_SYS_CSOR3 CONFIG_SYS_FPGA_CSOR
|
|
#define CONFIG_SYS_CS3_FTIM0 SYS_FPGA_CS_FTIM0
|
|
#define CONFIG_SYS_CS3_FTIM1 SYS_FPGA_CS_FTIM1
|
|
#define CONFIG_SYS_CS3_FTIM2 SYS_FPGA_CS_FTIM2
|
|
#define CONFIG_SYS_CS3_FTIM3 SYS_FPGA_CS_FTIM3
|
|
#endif
|
|
#endif
|
|
|
|
#define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
|
|
|
|
/*
|
|
* I2C bus multiplexer
|
|
*/
|
|
#define I2C_MUX_PCA_ADDR_PRI 0x77
|
|
#define I2C_MUX_PCA_ADDR_SEC 0x76 /* Secondary multiplexer */
|
|
#define I2C_RETIMER_ADDR 0x18
|
|
#define I2C_RETIMER_ADDR2 0x19
|
|
#define I2C_MUX_CH_DEFAULT 0x8
|
|
#define I2C_MUX_CH5 0xD
|
|
|
|
#define I2C_MUX_CH_VOL_MONITOR 0xA
|
|
|
|
/* Voltage monitor on channel 2*/
|
|
#define I2C_VOL_MONITOR_ADDR 0x63
|
|
#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2
|
|
#define I2C_VOL_MONITOR_BUS_V_OVF 0x1
|
|
#define I2C_VOL_MONITOR_BUS_V_SHIFT 3
|
|
#define I2C_SVDD_MONITOR_ADDR 0x4F
|
|
|
|
#define CONFIG_VID_FLS_ENV "ls1088aqds_vdd_mv"
|
|
#define CONFIG_VID
|
|
|
|
/* The lowest and highest voltage allowed for LS1088AQDS */
|
|
#define VDD_MV_MIN 819
|
|
#define VDD_MV_MAX 1212
|
|
|
|
#define CONFIG_VOL_MONITOR_LTC3882_SET
|
|
#define CONFIG_VOL_MONITOR_LTC3882_READ
|
|
|
|
#define PWM_CHANNEL0 0x0
|
|
|
|
/*
|
|
* RTC configuration
|
|
*/
|
|
#define RTC
|
|
#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Channel 3*/
|
|
|
|
/* EEPROM */
|
|
#define CONFIG_ID_EEPROM
|
|
#define CONFIG_SYS_I2C_EEPROM_NXID
|
|
#define CONFIG_SYS_EEPROM_BUS_NUM 0
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
|
|
|
|
#ifdef CONFIG_FSL_DSPI
|
|
#define CONFIG_SPI_FLASH_STMICRO
|
|
#define CONFIG_SPI_FLASH_SST
|
|
#define CONFIG_SPI_FLASH_EON
|
|
#if !defined(CONFIG_TFABOOT) && \
|
|
!defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
|
|
#endif
|
|
#endif
|
|
|
|
#ifdef CONFIG_SPL_BUILD
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
|
|
#else
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
|
|
#endif
|
|
|
|
#define CONFIG_FSL_MEMAC
|
|
|
|
/* MMC */
|
|
#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
|
|
#define CONFIG_ESDHC_DETECT_QUIRK ((readb(QIXIS_BASE + QIXIS_STAT_PRES1) & \
|
|
QIXIS_SDID_MASK) != QIXIS_ESDHC_NO_ADAPTER)
|
|
|
|
#define COMMON_ENV \
|
|
"kernelheader_addr_r=0x80200000\0" \
|
|
"fdtheader_addr_r=0x80100000\0" \
|
|
"kernel_addr_r=0x81000000\0" \
|
|
"fdt_addr_r=0x90000000\0" \
|
|
"load_addr=0xa0000000\0"
|
|
|
|
/* Initial environment variables */
|
|
#ifdef CONFIG_NXP_ESBC
|
|
#undef CONFIG_EXTRA_ENV_SETTINGS
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
COMMON_ENV \
|
|
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
|
|
"loadaddr=0x90100000\0" \
|
|
"kernel_addr=0x100000\0" \
|
|
"ramdisk_addr=0x800000\0" \
|
|
"ramdisk_size=0x2000000\0" \
|
|
"fdt_high=0xa0000000\0" \
|
|
"initrd_high=0xffffffffffffffff\0" \
|
|
"kernel_start=0x1000000\0" \
|
|
"kernel_load=0xa0000000\0" \
|
|
"kernel_size=0x2800000\0" \
|
|
"mcinitcmd=sf probe 0:0;sf read 0xa0a00000 0xa00000 0x100000;" \
|
|
"sf read 0xa0640000 0x640000 0x4000; esbc_validate 0xa0640000;" \
|
|
"sf read 0xa0e00000 0xe00000 0x100000;" \
|
|
"sf read 0xa0680000 0x680000 0x4000;esbc_validate 0xa0680000;" \
|
|
"fsl_mc start mc 0xa0a00000 0xa0e00000\0" \
|
|
"mcmemsize=0x70000000 \0"
|
|
#else /* if !(CONFIG_NXP_ESBC) */
|
|
#ifdef CONFIG_TFABOOT
|
|
#define QSPI_MC_INIT_CMD \
|
|
"sf probe 0:0;sf read 0x80000000 0xA00000 0x100000;" \
|
|
"sf read 0x80100000 0xE00000 0x100000;" \
|
|
"fsl_mc start mc 0x80000000 0x80100000\0"
|
|
#define SD_MC_INIT_CMD \
|
|
"mmcinfo;mmc read 0x80000000 0x5000 0x800;" \
|
|
"mmc read 0x80100000 0x7000 0x800;" \
|
|
"fsl_mc start mc 0x80000000 0x80100000\0"
|
|
#define IFC_MC_INIT_CMD \
|
|
"fsl_mc start mc 0x580A00000 0x580E00000\0"
|
|
|
|
#undef CONFIG_EXTRA_ENV_SETTINGS
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
COMMON_ENV \
|
|
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
|
|
"loadaddr=0x90100000\0" \
|
|
"kernel_addr=0x100000\0" \
|
|
"kernel_addr_sd=0x800\0" \
|
|
"ramdisk_addr=0x800000\0" \
|
|
"ramdisk_size=0x2000000\0" \
|
|
"fdt_high=0xa0000000\0" \
|
|
"initrd_high=0xffffffffffffffff\0" \
|
|
"kernel_start=0x1000000\0" \
|
|
"kernel_start_sd=0x8000\0" \
|
|
"kernel_load=0xa0000000\0" \
|
|
"kernel_size=0x2800000\0" \
|
|
"kernel_size_sd=0x14000\0" \
|
|
"mcinitcmd=sf probe 0:0;sf read 0x80000000 0xA00000 0x100000;" \
|
|
"sf read 0x80100000 0xE00000 0x100000;" \
|
|
"fsl_mc start mc 0x80000000 0x80100000\0" \
|
|
"mcmemsize=0x70000000 \0" \
|
|
"BOARD=ls1088aqds\0" \
|
|
"scriptaddr=0x80000000\0" \
|
|
"scripthdraddr=0x80080000\0" \
|
|
BOOTENV \
|
|
"boot_scripts=ls1088aqds_boot.scr\0" \
|
|
"boot_script_hdr=hdr_ls1088aqds_bs.out\0" \
|
|
"scan_dev_for_boot_part=" \
|
|
"part list ${devtype} ${devnum} devplist; " \
|
|
"env exists devplist || setenv devplist 1; " \
|
|
"for distro_bootpart in ${devplist}; do " \
|
|
"if fstype ${devtype} " \
|
|
"${devnum}:${distro_bootpart} " \
|
|
"bootfstype; then " \
|
|
"run scan_dev_for_boot; " \
|
|
"fi; " \
|
|
"done\0" \
|
|
"boot_a_script=" \
|
|
"load ${devtype} ${devnum}:${distro_bootpart} " \
|
|
"${scriptaddr} ${prefix}${script}; " \
|
|
"env exists secureboot && load ${devtype} " \
|
|
"${devnum}:${distro_bootpart} " \
|
|
"${scripthdraddr} ${prefix}${boot_script_hdr}; "\
|
|
"env exists secureboot " \
|
|
"&& esbc_validate ${scripthdraddr};" \
|
|
"source ${scriptaddr}\0" \
|
|
"qspi_bootcmd=echo Trying load from qspi..; " \
|
|
"sf probe 0:0; " \
|
|
"sf read 0x80001000 0xd00000 0x100000; " \
|
|
"fsl_mc lazyapply dpl 0x80001000 && " \
|
|
"sf read $kernel_load $kernel_start " \
|
|
"$kernel_size && bootm $kernel_load#$BOARD\0" \
|
|
"sd_bootcmd=echo Trying load from sd card..; " \
|
|
"mmcinfo;mmc read 0x80001000 0x6800 0x800; "\
|
|
"fsl_mc lazyapply dpl 0x80001000 && " \
|
|
"mmc read $kernel_load $kernel_start_sd " \
|
|
"$kernel_size_sd && bootm $kernel_load#$BOARD\0" \
|
|
"nor_bootcmd=echo Trying load from nor..; " \
|
|
"fsl_mc lazyapply dpl 0x580d00000 && " \
|
|
"cp.b $kernel_start $kernel_load " \
|
|
"$kernel_size && bootm $kernel_load#$BOARD\0"
|
|
#else
|
|
#if defined(CONFIG_QSPI_BOOT)
|
|
#undef CONFIG_EXTRA_ENV_SETTINGS
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
COMMON_ENV \
|
|
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
|
|
"loadaddr=0x90100000\0" \
|
|
"kernel_addr=0x100000\0" \
|
|
"ramdisk_addr=0x800000\0" \
|
|
"ramdisk_size=0x2000000\0" \
|
|
"fdt_high=0xa0000000\0" \
|
|
"initrd_high=0xffffffffffffffff\0" \
|
|
"kernel_start=0x1000000\0" \
|
|
"kernel_load=0xa0000000\0" \
|
|
"kernel_size=0x2800000\0" \
|
|
"mcinitcmd=sf probe 0:0;sf read 0x80000000 0xA00000 0x100000;" \
|
|
"sf read 0x80100000 0xE00000 0x100000;" \
|
|
"fsl_mc start mc 0x80000000 0x80100000\0" \
|
|
"mcmemsize=0x70000000 \0"
|
|
#elif defined(CONFIG_SD_BOOT)
|
|
#undef CONFIG_EXTRA_ENV_SETTINGS
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
COMMON_ENV \
|
|
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
|
|
"loadaddr=0x90100000\0" \
|
|
"kernel_addr=0x800\0" \
|
|
"ramdisk_addr=0x800000\0" \
|
|
"ramdisk_size=0x2000000\0" \
|
|
"fdt_high=0xa0000000\0" \
|
|
"initrd_high=0xffffffffffffffff\0" \
|
|
"kernel_start=0x8000\0" \
|
|
"kernel_load=0xa0000000\0" \
|
|
"kernel_size=0x14000\0" \
|
|
"mcinitcmd=mmcinfo;mmc read 0x80000000 0x5000 0x800;" \
|
|
"mmc read 0x80100000 0x7000 0x800;" \
|
|
"fsl_mc start mc 0x80000000 0x80100000\0" \
|
|
"mcmemsize=0x70000000 \0"
|
|
#else /* NOR BOOT */
|
|
#undef CONFIG_EXTRA_ENV_SETTINGS
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
COMMON_ENV \
|
|
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
|
|
"loadaddr=0x90100000\0" \
|
|
"kernel_addr=0x100000\0" \
|
|
"ramdisk_addr=0x800000\0" \
|
|
"ramdisk_size=0x2000000\0" \
|
|
"fdt_high=0xa0000000\0" \
|
|
"initrd_high=0xffffffffffffffff\0" \
|
|
"kernel_start=0x1000000\0" \
|
|
"kernel_load=0xa0000000\0" \
|
|
"kernel_size=0x2800000\0" \
|
|
"mcinitcmd=fsl_mc start mc 0x580A00000 0x580E00000\0" \
|
|
"mcmemsize=0x70000000 \0"
|
|
#endif
|
|
#endif /* CONFIG_TFABOOT */
|
|
#endif /* CONFIG_NXP_ESBC */
|
|
|
|
#ifdef CONFIG_TFABOOT
|
|
#define QSPI_NOR_BOOTCOMMAND "run distro_bootcmd; run qspi_bootcmd; " \
|
|
"env exists secureboot && esbc_halt;;"
|
|
#define IFC_NOR_BOOTCOMMAND "run distro_bootcmd; run nor_bootcmd; " \
|
|
"env exists secureboot && esbc_halt;;"
|
|
#define SD_BOOTCOMMAND "run distro_bootcmd; run sd_bootcmd; " \
|
|
"env exists secureboot && esbc_halt;;"
|
|
#endif
|
|
|
|
#ifdef CONFIG_FSL_MC_ENET
|
|
#define CONFIG_FSL_MEMAC
|
|
#define RGMII_PHY1_ADDR 0x1
|
|
#define RGMII_PHY2_ADDR 0x2
|
|
#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
|
|
#define SGMII_CARD_PORT2_PHY_ADDR 0x1d
|
|
#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
|
|
#define SGMII_CARD_PORT4_PHY_ADDR 0x1F
|
|
|
|
#define XQSGMII_CARD_PHY1_PORT0_ADDR 0x0
|
|
#define XQSGMII_CARD_PHY1_PORT1_ADDR 0x1
|
|
#define XQSGMII_CARD_PHY1_PORT2_ADDR 0x2
|
|
#define XQSGMII_CARD_PHY1_PORT3_ADDR 0x3
|
|
#define XQSGMII_CARD_PHY2_PORT0_ADDR 0x4
|
|
#define XQSGMII_CARD_PHY2_PORT1_ADDR 0x5
|
|
#define XQSGMII_CARD_PHY2_PORT2_ADDR 0x6
|
|
#define XQSGMII_CARD_PHY2_PORT3_ADDR 0x7
|
|
#define XQSGMII_CARD_PHY3_PORT0_ADDR 0x8
|
|
#define XQSGMII_CARD_PHY3_PORT1_ADDR 0x9
|
|
#define XQSGMII_CARD_PHY3_PORT2_ADDR 0xa
|
|
#define XQSGMII_CARD_PHY3_PORT3_ADDR 0xb
|
|
#define XQSGMII_CARD_PHY4_PORT0_ADDR 0xc
|
|
#define XQSGMII_CARD_PHY4_PORT1_ADDR 0xd
|
|
#define XQSGMII_CARD_PHY4_PORT2_ADDR 0xe
|
|
#define XQSGMII_CARD_PHY4_PORT3_ADDR 0xf
|
|
|
|
#define CONFIG_ETHPRIME "DPMAC1@xgmii"
|
|
#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
|
|
|
|
#endif
|
|
|
|
#define BOOT_TARGET_DEVICES(func) \
|
|
func(USB, usb, 0) \
|
|
func(MMC, mmc, 0) \
|
|
func(SCSI, scsi, 0) \
|
|
func(DHCP, dhcp, na)
|
|
#include <config_distro_bootcmd.h>
|
|
|
|
#include <asm/fsl_secure_boot.h>
|
|
|
|
#endif /* __LS1088A_QDS_H */
|