mirror of
https://github.com/u-boot/u-boot.git
synced 2024-12-16 00:03:26 +08:00
401d1c4f5d
Move this out of the common header and include it only where needed. In a number of cases this requires adding "struct udevice;" to avoid adding another large header or in other cases replacing / adding missing header files that had been pulled in, very indirectly. Finally, we have a few cases where we did not need to include <asm/global_data.h> at all, so remove that include. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
183 lines
4.5 KiB
C
183 lines
4.5 KiB
C
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* PCF8575 I2C GPIO EXPANDER DRIVER
|
|
*
|
|
* Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/
|
|
*
|
|
* Vignesh R <vigneshr@ti.com>
|
|
*
|
|
*
|
|
* Driver for TI PCF-8575 16-bit I2C gpio expander. Based on
|
|
* gpio-pcf857x Linux Kernel(v4.7) driver.
|
|
*
|
|
* Copyright (C) 2007 David Brownell
|
|
*
|
|
*/
|
|
|
|
/*
|
|
* NOTE: The driver and devicetree bindings are borrowed from Linux
|
|
* Kernel, but driver does not support all PCF857x devices. It currently
|
|
* supports PCF8575 16-bit expander by TI and NXP.
|
|
*
|
|
* TODO(vigneshr@ti.com):
|
|
* Support 8 bit PCF857x compatible expanders.
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <dm.h>
|
|
#include <i2c.h>
|
|
#include <log.h>
|
|
#include <asm-generic/gpio.h>
|
|
#include <asm/global_data.h>
|
|
#include <linux/bitops.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
struct pcf8575_chip {
|
|
int gpio_count; /* No. GPIOs supported by the chip */
|
|
|
|
/* NOTE: these chips have strange "quasi-bidirectional" I/O pins.
|
|
* We can't actually know whether a pin is configured (a) as output
|
|
* and driving the signal low, or (b) as input and reporting a low
|
|
* value ... without knowing the last value written since the chip
|
|
* came out of reset (if any). We can't read the latched output.
|
|
* In short, the only reliable solution for setting up pin direction
|
|
* is to do it explicitly.
|
|
*
|
|
* Using "out" avoids that trouble. When left initialized to zero,
|
|
* our software copy of the "latch" then matches the chip's all-ones
|
|
* reset state. Otherwise it flags pins to be driven low.
|
|
*/
|
|
unsigned int out; /* software latch */
|
|
const char *bank_name; /* Name of the expander bank */
|
|
};
|
|
|
|
/* Read/Write to 16-bit I/O expander */
|
|
|
|
static int pcf8575_i2c_write_le16(struct udevice *dev, unsigned int word)
|
|
{
|
|
struct dm_i2c_chip *chip = dev_get_parent_plat(dev);
|
|
u8 buf[2] = { word & 0xff, word >> 8, };
|
|
int ret;
|
|
|
|
ret = dm_i2c_write(dev, 0, buf, 2);
|
|
if (ret)
|
|
printf("%s i2c write failed to addr %x\n", __func__,
|
|
chip->chip_addr);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int pcf8575_i2c_read_le16(struct udevice *dev)
|
|
{
|
|
struct dm_i2c_chip *chip = dev_get_parent_plat(dev);
|
|
u8 buf[2];
|
|
int ret;
|
|
|
|
ret = dm_i2c_read(dev, 0, buf, 2);
|
|
if (ret) {
|
|
printf("%s i2c read failed from addr %x\n", __func__,
|
|
chip->chip_addr);
|
|
return ret;
|
|
}
|
|
|
|
return (buf[1] << 8) | buf[0];
|
|
}
|
|
|
|
static int pcf8575_direction_input(struct udevice *dev, unsigned offset)
|
|
{
|
|
struct pcf8575_chip *plat = dev_get_plat(dev);
|
|
int status;
|
|
|
|
plat->out |= BIT(offset);
|
|
status = pcf8575_i2c_write_le16(dev, plat->out);
|
|
|
|
return status;
|
|
}
|
|
|
|
static int pcf8575_direction_output(struct udevice *dev,
|
|
unsigned int offset, int value)
|
|
{
|
|
struct pcf8575_chip *plat = dev_get_plat(dev);
|
|
int ret;
|
|
|
|
if (value)
|
|
plat->out |= BIT(offset);
|
|
else
|
|
plat->out &= ~BIT(offset);
|
|
|
|
ret = pcf8575_i2c_write_le16(dev, plat->out);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int pcf8575_get_value(struct udevice *dev, unsigned int offset)
|
|
{
|
|
int value;
|
|
|
|
value = pcf8575_i2c_read_le16(dev);
|
|
|
|
return (value < 0) ? value : ((value & BIT(offset)) >> offset);
|
|
}
|
|
|
|
static int pcf8575_set_value(struct udevice *dev, unsigned int offset,
|
|
int value)
|
|
{
|
|
return pcf8575_direction_output(dev, offset, value);
|
|
}
|
|
|
|
static int pcf8575_ofdata_plat(struct udevice *dev)
|
|
{
|
|
struct pcf8575_chip *plat = dev_get_plat(dev);
|
|
struct gpio_dev_priv *uc_priv = dev_get_uclass_priv(dev);
|
|
|
|
int n_latch;
|
|
|
|
uc_priv->gpio_count = fdtdec_get_int(gd->fdt_blob, dev_of_offset(dev),
|
|
"gpio-count", 16);
|
|
uc_priv->bank_name = fdt_getprop(gd->fdt_blob, dev_of_offset(dev),
|
|
"gpio-bank-name", NULL);
|
|
if (!uc_priv->bank_name)
|
|
uc_priv->bank_name = fdt_get_name(gd->fdt_blob,
|
|
dev_of_offset(dev), NULL);
|
|
|
|
n_latch = fdtdec_get_uint(gd->fdt_blob, dev_of_offset(dev),
|
|
"lines-initial-states", 0);
|
|
plat->out = ~n_latch;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int pcf8575_gpio_probe(struct udevice *dev)
|
|
{
|
|
struct gpio_dev_priv *uc_priv = dev_get_uclass_priv(dev);
|
|
|
|
debug("%s GPIO controller with %d gpios probed\n",
|
|
uc_priv->bank_name, uc_priv->gpio_count);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct dm_gpio_ops pcf8575_gpio_ops = {
|
|
.direction_input = pcf8575_direction_input,
|
|
.direction_output = pcf8575_direction_output,
|
|
.get_value = pcf8575_get_value,
|
|
.set_value = pcf8575_set_value,
|
|
};
|
|
|
|
static const struct udevice_id pcf8575_gpio_ids[] = {
|
|
{ .compatible = "nxp,pcf8575" },
|
|
{ .compatible = "ti,pcf8575" },
|
|
{ }
|
|
};
|
|
|
|
U_BOOT_DRIVER(gpio_pcf8575) = {
|
|
.name = "gpio_pcf8575",
|
|
.id = UCLASS_GPIO,
|
|
.ops = &pcf8575_gpio_ops,
|
|
.of_match = pcf8575_gpio_ids,
|
|
.of_to_plat = pcf8575_ofdata_plat,
|
|
.probe = pcf8575_gpio_probe,
|
|
.plat_auto = sizeof(struct pcf8575_chip),
|
|
};
|