mirror of
https://github.com/u-boot/u-boot.git
synced 2024-12-27 05:33:27 +08:00
584550d76a
These config targets were added well before the Kconfig migration began as a way to demonstrate how to make these platforms work with cut down features. At this point in time they no longer serve a good purpose so remove them. Signed-off-by: Tom Rini <trini@konsulko.com>
414 lines
12 KiB
C
414 lines
12 KiB
C
/*
|
|
* Configuration settings for the TI OMAP3 EVM board.
|
|
*
|
|
* Copyright (C) 2006-2011 Texas Instruments Incorporated - http://www.ti.com/
|
|
*
|
|
* Author :
|
|
* Manikandan Pillai <mani.pillai@ti.com>
|
|
* Derived from Beagle Board and 3430 SDP code by
|
|
* Richard Woodruff <r-woodruff2@ti.com>
|
|
* Syed Mohammed Khasim <khasim@ti.com>
|
|
*
|
|
* Manikandan Pillai <mani.pillai@ti.com>
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#ifndef __OMAP3EVM_CONFIG_H
|
|
#define __OMAP3EVM_CONFIG_H
|
|
|
|
#include <asm/arch/cpu.h>
|
|
#include <asm/arch/omap.h>
|
|
|
|
/* ----------------------------------------------------------------------------
|
|
* Supported U-Boot commands
|
|
* ----------------------------------------------------------------------------
|
|
*/
|
|
|
|
#define CONFIG_CMD_JFFS2
|
|
|
|
#define CONFIG_CMD_NAND
|
|
|
|
/* ----------------------------------------------------------------------------
|
|
* Supported U-Boot features
|
|
* ----------------------------------------------------------------------------
|
|
*/
|
|
#define CONFIG_SYS_LONGHELP
|
|
|
|
/* Display CPU and Board information */
|
|
#define CONFIG_DISPLAY_CPUINFO
|
|
#define CONFIG_DISPLAY_BOARDINFO
|
|
|
|
/* Allow to overwrite serial and ethaddr */
|
|
#define CONFIG_ENV_OVERWRITE
|
|
|
|
/* Add auto-completion support */
|
|
#define CONFIG_AUTO_COMPLETE
|
|
|
|
/* ----------------------------------------------------------------------------
|
|
* Supported hardware
|
|
* ----------------------------------------------------------------------------
|
|
*/
|
|
|
|
/* MMC */
|
|
#define CONFIG_MMC
|
|
#define CONFIG_GENERIC_MMC
|
|
#define CONFIG_OMAP_HSMMC
|
|
|
|
/* SPL */
|
|
#define CONFIG_SPL_MMC_SUPPORT
|
|
#define CONFIG_SPL_FAT_SUPPORT
|
|
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
|
|
#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
|
|
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
|
|
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
|
|
|
|
/* Partition tables */
|
|
#define CONFIG_EFI_PARTITION
|
|
#define CONFIG_DOS_PARTITION
|
|
|
|
/* USB
|
|
*
|
|
* Enable CONFIG_USB_MUSB_HCD for Host functionalities MSC, keyboard
|
|
* Enable CONFIG_USB_MUSB_UDD for Device functionalities.
|
|
*/
|
|
#define CONFIG_USB_OMAP3
|
|
#define CONFIG_USB_MUSB_HCD
|
|
/* #define CONFIG_USB_MUSB_UDC */
|
|
|
|
/* NAND SPL */
|
|
#define CONFIG_SPL_NAND_SIMPLE
|
|
#define CONFIG_SPL_NAND_SUPPORT
|
|
#define CONFIG_SPL_NAND_BASE
|
|
#define CONFIG_SPL_NAND_DRIVERS
|
|
#define CONFIG_SPL_NAND_ECC
|
|
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
|
|
#define CONFIG_SYS_NAND_PAGE_COUNT 64
|
|
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
|
|
#define CONFIG_SYS_NAND_OOBSIZE 64
|
|
#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
|
|
#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
|
|
#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\
|
|
10, 11, 12, 13}
|
|
#define CONFIG_SYS_NAND_ECCSIZE 512
|
|
#define CONFIG_SYS_NAND_ECCBYTES 3
|
|
#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW
|
|
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
|
|
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
|
|
|
|
/*
|
|
* High level configuration options
|
|
*/
|
|
#define CONFIG_OMAP /* This is TI OMAP core */
|
|
#define CONFIG_OMAP_GPIO
|
|
#define CONFIG_OMAP_COMMON
|
|
/* Common ARM Erratas */
|
|
#define CONFIG_ARM_ERRATA_454179
|
|
#define CONFIG_ARM_ERRATA_430973
|
|
#define CONFIG_ARM_ERRATA_621766
|
|
|
|
#define CONFIG_SDRC /* The chip has SDRC controller */
|
|
|
|
#define CONFIG_OMAP3_EVM /* This is a OMAP3 EVM */
|
|
#define CONFIG_TWL4030_POWER /* with TWL4030 PMIC */
|
|
|
|
/*
|
|
* Clock related definitions
|
|
*/
|
|
#define V_OSCK 26000000 /* Clock output from T2 */
|
|
#define V_SCLK (V_OSCK >> 1)
|
|
|
|
/*
|
|
* OMAP3 has 12 GP timers, they can be driven by the system clock
|
|
* (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
|
|
* This rate is divided by a local divisor.
|
|
*/
|
|
#define CONFIG_SYS_TIMERBASE OMAP34XX_GPT2
|
|
#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
|
|
|
|
/* Size of environment - 128KB */
|
|
#define CONFIG_ENV_SIZE (128 << 10)
|
|
|
|
/* Size of malloc pool */
|
|
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
|
|
|
|
/*
|
|
* Physical Memory Map
|
|
* Note 1: CS1 may or may not be populated
|
|
* Note 2: SDRAM size is expected to be at least 32MB
|
|
*/
|
|
#define CONFIG_NR_DRAM_BANKS 2
|
|
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
|
|
#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
|
|
|
|
/* Limits for memtest */
|
|
#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0)
|
|
#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
|
|
0x01F00000) /* 31MB */
|
|
|
|
/* Default load address */
|
|
#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0)
|
|
|
|
/* -----------------------------------------------------------------------------
|
|
* Hardware drivers
|
|
* -----------------------------------------------------------------------------
|
|
*/
|
|
|
|
/*
|
|
* NS16550 Configuration
|
|
*/
|
|
#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
|
|
|
|
#define CONFIG_SYS_NS16550_SERIAL
|
|
#define CONFIG_SYS_NS16550_REG_SIZE (-4)
|
|
#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
|
|
|
|
/*
|
|
* select serial console configuration
|
|
*/
|
|
#define CONFIG_CONS_INDEX 1
|
|
#define CONFIG_SERIAL1 1 /* UART1 on OMAP3 EVM */
|
|
#define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1
|
|
#define CONFIG_BAUDRATE 115200
|
|
#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
|
|
115200}
|
|
|
|
/*
|
|
* I2C
|
|
*/
|
|
#define CONFIG_SYS_I2C
|
|
#define CONFIG_SYS_OMAP24_I2C_SPEED 100000
|
|
#define CONFIG_SYS_OMAP24_I2C_SLAVE 1
|
|
#define CONFIG_SYS_I2C_OMAP34XX
|
|
|
|
/*
|
|
* PISMO support
|
|
*/
|
|
/* Monitor at start of flash - Reserve 2 sectors */
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
|
|
|
|
#define CONFIG_SYS_MONITOR_LEN (256 << 10)
|
|
|
|
/* Start location & size of environment */
|
|
#define ONENAND_ENV_OFFSET 0x260000
|
|
#define SMNAND_ENV_OFFSET 0x260000
|
|
|
|
#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
|
|
|
|
/*
|
|
* NAND
|
|
*/
|
|
/* Physical address to access NAND */
|
|
#define CONFIG_SYS_NAND_ADDR NAND_BASE
|
|
|
|
/* Physical address to access NAND at CS0 */
|
|
#define CONFIG_SYS_NAND_BASE NAND_BASE
|
|
|
|
/* Max number of NAND devices */
|
|
#define CONFIG_SYS_MAX_NAND_DEVICE 1
|
|
#define CONFIG_SYS_NAND_BUSWIDTH_16BIT
|
|
/* Timeout values (in ticks) */
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ)
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ)
|
|
|
|
/* Flash banks JFFS2 should use */
|
|
#define CONFIG_SYS_MAX_MTD_BANKS (CONFIG_SYS_MAX_FLASH_BANKS + \
|
|
CONFIG_SYS_MAX_NAND_DEVICE)
|
|
|
|
#define CONFIG_SYS_JFFS2_MEM_NAND
|
|
#define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS
|
|
#define CONFIG_SYS_JFFS2_NUM_BANKS 1
|
|
|
|
#define CONFIG_JFFS2_NAND
|
|
/* nand device jffs2 lives on */
|
|
#define CONFIG_JFFS2_DEV "nand0"
|
|
/* Start of jffs2 partition */
|
|
#define CONFIG_JFFS2_PART_OFFSET 0x680000
|
|
/* Size of jffs2 partition */
|
|
#define CONFIG_JFFS2_PART_SIZE 0xf980000
|
|
|
|
/*
|
|
* USB
|
|
*/
|
|
#ifdef CONFIG_USB_OMAP3
|
|
|
|
#ifdef CONFIG_USB_MUSB_HCD
|
|
|
|
#define CONFIG_USB_STORAGE
|
|
#define CONGIG_CMD_STORAGE
|
|
|
|
#ifdef CONFIG_USB_KEYBOARD
|
|
#define CONFIG_SYS_USB_EVENT_POLL
|
|
#define CONFIG_PREBOOT "usb start"
|
|
#endif /* CONFIG_USB_KEYBOARD */
|
|
|
|
#endif /* CONFIG_USB_MUSB_HCD */
|
|
|
|
#ifdef CONFIG_USB_MUSB_UDC
|
|
/* USB device configuration */
|
|
#define CONFIG_USB_DEVICE
|
|
#define CONFIG_USB_TTY
|
|
#define CONFIG_SYS_CONSOLE_IS_IN_ENV
|
|
|
|
/* Change these to suit your needs */
|
|
#define CONFIG_USBD_VENDORID 0x0451
|
|
#define CONFIG_USBD_PRODUCTID 0x5678
|
|
#define CONFIG_USBD_MANUFACTURER "Texas Instruments"
|
|
#define CONFIG_USBD_PRODUCT_NAME "EVM"
|
|
#endif /* CONFIG_USB_MUSB_UDC */
|
|
|
|
#endif /* CONFIG_USB_OMAP3 */
|
|
|
|
/* ----------------------------------------------------------------------------
|
|
* U-Boot features
|
|
* ----------------------------------------------------------------------------
|
|
*/
|
|
#define CONFIG_SYS_MAXARGS 16 /* max args for a command */
|
|
|
|
#define CONFIG_MISC_INIT_R
|
|
|
|
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
|
|
#define CONFIG_SETUP_MEMORY_TAGS
|
|
#define CONFIG_INITRD_TAG
|
|
#define CONFIG_REVISION_TAG
|
|
|
|
/* Size of Console IO buffer */
|
|
#define CONFIG_SYS_CBSIZE 512
|
|
|
|
/* Size of print buffer */
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
|
|
sizeof(CONFIG_SYS_PROMPT) + 16)
|
|
|
|
/* Size of bootarg buffer */
|
|
#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
|
|
|
|
#define CONFIG_BOOTFILE "uImage"
|
|
|
|
/*
|
|
* NAND / OneNAND
|
|
*/
|
|
#if defined(CONFIG_CMD_NAND)
|
|
#define CONFIG_SYS_FLASH_BASE NAND_BASE
|
|
|
|
#define CONFIG_NAND_OMAP_GPMC
|
|
#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
|
|
#elif defined(CONFIG_CMD_ONENAND)
|
|
#define CONFIG_SYS_FLASH_BASE ONENAND_MAP
|
|
#define CONFIG_SYS_ONENAND_BASE ONENAND_MAP
|
|
#endif
|
|
|
|
#if !defined(CONFIG_ENV_IS_NOWHERE)
|
|
#if defined(CONFIG_CMD_NAND)
|
|
#define CONFIG_ENV_IS_IN_NAND
|
|
#elif defined(CONFIG_CMD_ONENAND)
|
|
#define CONFIG_ENV_IS_IN_ONENAND
|
|
#define CONFIG_ENV_OFFSET ONENAND_ENV_OFFSET
|
|
#endif
|
|
#endif /* CONFIG_ENV_IS_NOWHERE */
|
|
|
|
#define CONFIG_ENV_ADDR CONFIG_ENV_OFFSET
|
|
|
|
#if defined(CONFIG_CMD_NET)
|
|
|
|
/* Ethernet (SMSC9115 from SMSC9118 family) */
|
|
#define CONFIG_SMC911X
|
|
#define CONFIG_SMC911X_32_BIT
|
|
#define CONFIG_SMC911X_BASE 0x2C000000
|
|
|
|
/* BOOTP fields */
|
|
#define CONFIG_BOOTP_SUBNETMASK 0x00000001
|
|
#define CONFIG_BOOTP_GATEWAY 0x00000002
|
|
#define CONFIG_BOOTP_HOSTNAME 0x00000004
|
|
#define CONFIG_BOOTP_BOOTPATH 0x00000010
|
|
|
|
#endif /* CONFIG_CMD_NET */
|
|
|
|
/* Support for relocation */
|
|
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
|
|
#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
|
|
#define CONFIG_SYS_INIT_RAM_SIZE 0x800
|
|
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
|
|
CONFIG_SYS_INIT_RAM_SIZE - \
|
|
GENERATED_GBL_DATA_SIZE)
|
|
|
|
/* -----------------------------------------------------------------------------
|
|
* Board specific
|
|
* -----------------------------------------------------------------------------
|
|
*/
|
|
#define CONFIG_SYS_NO_FLASH
|
|
|
|
/* Uncomment to define the board revision statically */
|
|
/* #define CONFIG_STATIC_BOARD_REV OMAP3EVM_BOARD_GEN_2 */
|
|
|
|
#define CONFIG_SYS_CACHELINE_SIZE 64
|
|
|
|
/* Defines for SPL */
|
|
#define CONFIG_SPL_FRAMEWORK
|
|
#define CONFIG_SPL_TEXT_BASE 0x40200800
|
|
#define CONFIG_SPL_MAX_SIZE (54 * 1024) /* 8 KB for stack */
|
|
|
|
#define CONFIG_SPL_BSS_START_ADDR 0x80000000
|
|
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
|
|
|
|
#define CONFIG_SPL_BOARD_INIT
|
|
#define CONFIG_SPL_LIBCOMMON_SUPPORT
|
|
#define CONFIG_SPL_LIBDISK_SUPPORT
|
|
#define CONFIG_SPL_I2C_SUPPORT
|
|
#define CONFIG_SPL_LIBGENERIC_SUPPORT
|
|
#define CONFIG_SPL_SERIAL_SUPPORT
|
|
#define CONFIG_SPL_POWER_SUPPORT
|
|
#define CONFIG_SPL_OMAP3_ID_NAND
|
|
#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
|
|
|
|
/*
|
|
* 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
|
|
* 64 bytes before this address should be set aside for u-boot.img's
|
|
* header. That is 0x800FFFC0--0x80100000 should not be used for any
|
|
* other needs.
|
|
*/
|
|
#define CONFIG_SYS_TEXT_BASE 0x80100000
|
|
#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
|
|
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
|
|
|
|
/* -----------------------------------------------------------------------------
|
|
* Default environment
|
|
* -----------------------------------------------------------------------------
|
|
*/
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"loadaddr=0x82000000\0" \
|
|
"usbtty=cdc_acm\0" \
|
|
"mmcdev=0\0" \
|
|
"console=ttyO0,115200n8\0" \
|
|
"mmcargs=setenv bootargs console=${console} " \
|
|
"root=/dev/mmcblk0p2 rw " \
|
|
"rootfstype=ext3 rootwait\0" \
|
|
"nandargs=setenv bootargs console=${console} " \
|
|
"root=/dev/mtdblock4 rw " \
|
|
"rootfstype=jffs2\0" \
|
|
"loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
|
|
"bootscript=echo Running bootscript from mmc ...; " \
|
|
"source ${loadaddr}\0" \
|
|
"loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
|
|
"mmcboot=echo Booting from mmc ...; " \
|
|
"run mmcargs; " \
|
|
"bootm ${loadaddr}\0" \
|
|
"nandboot=echo Booting from nand ...; " \
|
|
"run nandargs; " \
|
|
"onenand read ${loadaddr} 280000 400000; " \
|
|
"bootm ${loadaddr}\0" \
|
|
|
|
#define CONFIG_BOOTCOMMAND \
|
|
"mmc dev ${mmcdev}; if mmc rescan; then " \
|
|
"if run loadbootscript; then " \
|
|
"run bootscript; " \
|
|
"else " \
|
|
"if run loaduimage; then " \
|
|
"run mmcboot; " \
|
|
"else run nandboot; " \
|
|
"fi; " \
|
|
"fi; " \
|
|
"else run nandboot; fi"
|
|
|
|
#endif /* __OMAP3EVM_CONFIG_H */
|