mirror of
https://github.com/u-boot/u-boot.git
synced 2024-12-01 00:23:29 +08:00
700a0c648d
Old, obsolete and duplicated code was cleaned up and replace by the new partitioning method. There are two possible approaches now: * define a single, static partition * use mtdparts command line option and dynamic partitioning Default is static partitioning.
594 lines
19 KiB
C
594 lines
19 KiB
C
/*
|
|
* (C) Copyright 2001
|
|
* Stuart Hughes <stuarth@lineo.com>
|
|
* This file is based on similar values for other boards found in other
|
|
* U-Boot config files, and some that I found in the mpc8260ads manual.
|
|
*
|
|
* Note: my board is a PILOT rev.
|
|
* Note: the mpc8260ads doesn't come with a proper Ethernet MAC address.
|
|
*
|
|
* See file CREDITS for list of people who contributed to this
|
|
* project.
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License as
|
|
* published by the Free Software Foundation; either version 2 of
|
|
* the License, or (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
|
|
* MA 02111-1307 USA
|
|
*/
|
|
|
|
/*
|
|
* Config header file for a MPC8266ADS Pilot 16M Ram Simm, 8Mbytes Flash Simm
|
|
*/
|
|
|
|
/* !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
|
|
!! !!
|
|
!! This configuration requires JP3 to be in position 1-2 to work !!
|
|
!! To make it work for the default, the TEXT_BASE define in !!
|
|
!! board/mpc8266ads/config.mk must be changed from 0xfe000000 to !!
|
|
!! 0xfff00000 !!
|
|
!! The CFG_HRCW_MASTER define below must also be changed to match !!
|
|
!! !!
|
|
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
* (easy to change)
|
|
*/
|
|
|
|
#define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */
|
|
#define CONFIG_MPC8266ADS 1 /* ...on motorola ADS board */
|
|
#define CONFIG_CPM2 1 /* Has a CPM2 */
|
|
|
|
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
|
|
|
|
/* allow serial and ethaddr to be overwritten */
|
|
#define CONFIG_ENV_OVERWRITE
|
|
|
|
/*
|
|
* select serial console configuration
|
|
*
|
|
* if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
|
|
* CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
|
|
* for SCC).
|
|
*
|
|
* if CONFIG_CONS_NONE is defined, then the serial console routines must
|
|
* defined elsewhere (for example, on the cogent platform, there are serial
|
|
* ports on the motherboard which are used for the serial console - see
|
|
* cogent/cma101/serial.[ch]).
|
|
*/
|
|
#undef CONFIG_CONS_ON_SMC /* define if console on SMC */
|
|
#define CONFIG_CONS_ON_SCC /* define if console on SCC */
|
|
#undef CONFIG_CONS_NONE /* define if console on something else */
|
|
#define CONFIG_CONS_INDEX 1 /* which serial channel for console */
|
|
|
|
/*
|
|
* select ethernet configuration
|
|
*
|
|
* if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
|
|
* CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
|
|
* for FCC)
|
|
*
|
|
* if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
|
|
* defined elsewhere (as for the console), or CFG_CMD_NET must be removed
|
|
* from CONFIG_COMMANDS to remove support for networking.
|
|
*/
|
|
#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */
|
|
#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */
|
|
#undef CONFIG_ETHER_NONE /* define if ether on something else */
|
|
#define CONFIG_ETHER_INDEX 2 /* which channel for ether */
|
|
#define CONFIG_MII /* MII PHY management */
|
|
#define CONFIG_BITBANGMII /* bit-bang MII PHY management */
|
|
/*
|
|
* Port pins used for bit-banged MII communictions (if applicable).
|
|
*/
|
|
#define MDIO_PORT 2 /* Port C */
|
|
#define MDIO_ACTIVE (iop->pdir |= 0x00400000)
|
|
#define MDIO_TRISTATE (iop->pdir &= ~0x00400000)
|
|
#define MDIO_READ ((iop->pdat & 0x00400000) != 0)
|
|
|
|
#define MDIO(bit) if(bit) iop->pdat |= 0x00400000; \
|
|
else iop->pdat &= ~0x00400000
|
|
|
|
#define MDC(bit) if(bit) iop->pdat |= 0x00200000; \
|
|
else iop->pdat &= ~0x00200000
|
|
|
|
#define MIIDELAY udelay(1)
|
|
|
|
#if (CONFIG_ETHER_INDEX == 2)
|
|
|
|
/*
|
|
* - Rx-CLK is CLK13
|
|
* - Tx-CLK is CLK14
|
|
* - Select bus for bd/buffers (see 28-13)
|
|
* - Half duplex
|
|
*/
|
|
# define CFG_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
|
|
# define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
|
|
# define CFG_CPMFCR_RAMTYPE 0
|
|
# define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB)
|
|
|
|
#endif /* CONFIG_ETHER_INDEX */
|
|
|
|
/* other options */
|
|
#define CONFIG_HARD_I2C 1 /* To enable I2C support */
|
|
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
|
|
#define CFG_I2C_SLAVE 0x7F
|
|
#define CFG_I2C_EEPROM_ADDR_LEN 1
|
|
|
|
/* PCI */
|
|
#define CONFIG_PCI
|
|
#define CONFIG_PCI_PNP
|
|
#define CONFIG_PCI_BOOTDELAY 0
|
|
#undef CONFIG_PCI_SCAN_SHOW
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Definitions for Serial Presence Detect EEPROM address
|
|
* (to get SDRAM settings)
|
|
*/
|
|
#define SPD_EEPROM_ADDRESS 0x50
|
|
|
|
|
|
#define CONFIG_8260_CLKIN 66000000 /* in Hz */
|
|
#define CONFIG_BAUDRATE 115200
|
|
|
|
|
|
#define CONFIG_COMMANDS ( CFG_CMD_ALL & ~( \
|
|
CFG_CMD_BEDBUG | \
|
|
CFG_CMD_BMP | \
|
|
CFG_CMD_BSP | \
|
|
CFG_CMD_DATE | \
|
|
CFG_CMD_DHCP | \
|
|
CFG_CMD_DOC | \
|
|
CFG_CMD_DTT | \
|
|
CFG_CMD_EEPROM | \
|
|
CFG_CMD_ELF | \
|
|
CFG_CMD_EXT2 | \
|
|
CFG_CMD_FDC | \
|
|
CFG_CMD_FDOS | \
|
|
CFG_CMD_HWFLOW | \
|
|
CFG_CMD_IDE | \
|
|
CFG_CMD_JFFS2 | \
|
|
CFG_CMD_KGDB | \
|
|
CFG_CMD_MMC | \
|
|
CFG_CMD_NAND | \
|
|
CFG_CMD_PCMCIA | \
|
|
CFG_CMD_REISER | \
|
|
CFG_CMD_SCSI | \
|
|
CFG_CMD_SPI | \
|
|
CFG_CMD_SNTP | \
|
|
CFG_CMD_VFD | \
|
|
CFG_CMD_UNIVERSE | \
|
|
CFG_CMD_USB | \
|
|
CFG_CMD_XIMG ) )
|
|
|
|
/* Define a command string that is automatically executed when no character
|
|
* is read on the console interface withing "Boot Delay" after reset.
|
|
*/
|
|
#undef CONFIG_BOOT_ROOT_INITRD /* Use ram disk for the root file system */
|
|
#define CONFIG_BOOT_ROOT_NFS /* Use a NFS mounted root file system */
|
|
|
|
#ifdef CONFIG_BOOT_ROOT_INITRD
|
|
#define CONFIG_BOOTCOMMAND \
|
|
"version;" \
|
|
"echo;" \
|
|
"bootp;" \
|
|
"setenv bootargs root=/dev/ram0 rw " \
|
|
"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
|
|
"bootm"
|
|
#endif /* CONFIG_BOOT_ROOT_INITRD */
|
|
|
|
#ifdef CONFIG_BOOT_ROOT_NFS
|
|
#define CONFIG_BOOTCOMMAND \
|
|
"version;" \
|
|
"echo;" \
|
|
"bootp;" \
|
|
"setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
|
|
"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
|
|
"bootm"
|
|
#endif /* CONFIG_BOOT_ROOT_NFS */
|
|
|
|
/* Add support for a few extra bootp options like:
|
|
* - File size
|
|
* - DNS
|
|
*/
|
|
#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \
|
|
CONFIG_BOOTP_BOOTFILESIZE | \
|
|
CONFIG_BOOTP_DNS)
|
|
|
|
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
|
|
#include <cmd_confdefs.h>
|
|
|
|
|
|
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
|
|
|
|
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
|
|
#undef CONFIG_KGDB_ON_SMC /* define if kgdb on SMC */
|
|
#define CONFIG_KGDB_ON_SCC /* define if kgdb on SCC */
|
|
#undef CONFIG_KGDB_NONE /* define if kgdb on something else */
|
|
#define CONFIG_KGDB_INDEX 2 /* which serial channel for kgdb */
|
|
#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port at */
|
|
#endif
|
|
|
|
#undef CONFIG_WATCHDOG /* disable platform specific watchdog */
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CFG_LONGHELP /* undef to save memory */
|
|
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
|
|
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
|
|
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
#else
|
|
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
|
|
#endif
|
|
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
|
|
#define CFG_MAXARGS 16 /* max number of command args */
|
|
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
|
|
|
|
#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
|
|
#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
|
|
|
|
#undef CONFIG_CLOCKS_IN_MHZ /* clocks passsed to Linux in MHz */
|
|
/* for versions < 2.4.5-pre5 */
|
|
|
|
#define CFG_LOAD_ADDR 0x100000 /* default load address */
|
|
|
|
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
|
|
|
|
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
|
|
|
|
#define CFG_FLASH_BASE 0xFE000000
|
|
#define FLASH_BASE 0xFE000000
|
|
#define CFG_MAX_FLASH_BANKS 1 /* max num of memory banks */
|
|
#define CFG_MAX_FLASH_SECT 32 /* max num of sects on one chip */
|
|
#define CFG_FLASH_SIZE 8
|
|
#define CFG_FLASH_ERASE_TOUT 8000 /* Timeout for Flash Erase (in ms) */
|
|
#define CFG_FLASH_WRITE_TOUT 5 /* Timeout for Flash Write (in ms) */
|
|
|
|
#undef CFG_FLASH_CHECKSUM
|
|
|
|
/* this is stuff came out of the Motorola docs */
|
|
/* Only change this if you also change the Hardware configuration Word */
|
|
#define CFG_DEFAULT_IMMR 0x0F010000
|
|
|
|
/* Set IMMR to 0xF0000000 or above to boot Linux */
|
|
#define CFG_IMMR 0xF0000000
|
|
#define CFG_BCSR 0xF8000000
|
|
#define CFG_PCI_INT 0xF8200000 /* PCI interrupt controller */
|
|
|
|
/* Define CONFIG_VERY_BIG_RAM to allow use of SDRAMs larger than 256MBytes
|
|
*/
|
|
/*#define CONFIG_VERY_BIG_RAM 1*/
|
|
|
|
/* What should be the base address of SDRAM DIMM and how big is
|
|
* it (in Mbytes)? This will normally auto-configure via the SPD.
|
|
*/
|
|
#define CFG_SDRAM_BASE 0x00000000
|
|
#define CFG_SDRAM_SIZE 16
|
|
|
|
#define SDRAM_SPD_ADDR 0x50
|
|
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* BR2,BR3 - Base Register
|
|
* Ref: Section 10.3.1 on page 10-14
|
|
* OR2,OR3 - Option Register
|
|
* Ref: Section 10.3.2 on page 10-16
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
|
|
/* Bank 2,3 - SDRAM DIMM
|
|
*/
|
|
|
|
/* The BR2 is configured as follows:
|
|
*
|
|
* - Base address of 0x00000000
|
|
* - 64 bit port size (60x bus only)
|
|
* - Data errors checking is disabled
|
|
* - Read and write access
|
|
* - SDRAM 60x bus
|
|
* - Access are handled by the memory controller according to MSEL
|
|
* - Not used for atomic operations
|
|
* - No data pipelining is done
|
|
* - Valid
|
|
*/
|
|
#define CFG_BR2_PRELIM ((CFG_SDRAM_BASE & BRx_BA_MSK) |\
|
|
BRx_PS_64 |\
|
|
BRx_MS_SDRAM_P |\
|
|
BRx_V)
|
|
|
|
#define CFG_BR3_PRELIM ((CFG_SDRAM_BASE & BRx_BA_MSK) |\
|
|
BRx_PS_64 |\
|
|
BRx_MS_SDRAM_P |\
|
|
BRx_V)
|
|
|
|
/* With a 64 MB DIMM, the OR2 is configured as follows:
|
|
*
|
|
* - 64 MB
|
|
* - 4 internal banks per device
|
|
* - Row start address bit is A8 with PSDMR[PBI] = 0
|
|
* - 12 row address lines
|
|
* - Back-to-back page mode
|
|
* - Internal bank interleaving within save device enabled
|
|
*/
|
|
#if (CFG_SDRAM_SIZE == 64)
|
|
#define CFG_OR2_PRELIM (MEG_TO_AM(CFG_SDRAM_SIZE) |\
|
|
ORxS_BPD_4 |\
|
|
ORxS_ROWST_PBI0_A8 |\
|
|
ORxS_NUMR_12)
|
|
#elif (CFG_SDRAM_SIZE == 16)
|
|
#define CFG_OR2_PRELIM (0xFF000C80)
|
|
#else
|
|
#error "INVALID SDRAM CONFIGURATION"
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PSDMR - 60x Bus SDRAM Mode Register
|
|
* Ref: Section 10.3.3 on page 10-21
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
|
|
#if (CFG_SDRAM_SIZE == 64)
|
|
/* With a 64 MB DIMM, the PSDMR is configured as follows:
|
|
*
|
|
* - Bank Based Interleaving,
|
|
* - Refresh Enable,
|
|
* - Address Multiplexing where A5 is output on A14 pin
|
|
* (A6 on A15, and so on),
|
|
* - use address pins A14-A16 as bank select,
|
|
* - A9 is output on SDA10 during an ACTIVATE command,
|
|
* - earliest timing for ACTIVATE command after REFRESH command is 7 clocks,
|
|
* - earliest timing for ACTIVATE or REFRESH command after PRECHARGE command
|
|
* is 3 clocks,
|
|
* - earliest timing for READ/WRITE command after ACTIVATE command is
|
|
* 2 clocks,
|
|
* - earliest timing for PRECHARGE after last data was read is 1 clock,
|
|
* - earliest timing for PRECHARGE after last data was written is 1 clock,
|
|
* - CAS Latency is 2.
|
|
*/
|
|
#define CFG_PSDMR (PSDMR_RFEN |\
|
|
PSDMR_SDAM_A14_IS_A5 |\
|
|
PSDMR_BSMA_A14_A16 |\
|
|
PSDMR_SDA10_PBI0_A9 |\
|
|
PSDMR_RFRC_7_CLK |\
|
|
PSDMR_PRETOACT_3W |\
|
|
PSDMR_ACTTORW_2W |\
|
|
PSDMR_LDOTOPRE_1C |\
|
|
PSDMR_WRC_1C |\
|
|
PSDMR_CL_2)
|
|
#elif (CFG_SDRAM_SIZE == 16)
|
|
/* With a 16 MB DIMM, the PSDMR is configured as follows:
|
|
*
|
|
* configuration parameters found in Motorola documentation
|
|
*/
|
|
#define CFG_PSDMR (0x016EB452)
|
|
#else
|
|
#error "INVALID SDRAM CONFIGURATION"
|
|
#endif
|
|
|
|
|
|
#define RS232EN_1 0x02000002
|
|
#define RS232EN_2 0x01000001
|
|
#define FETHIEN 0x08000008
|
|
#define FETH_RST 0x04000004
|
|
|
|
#define CFG_INIT_RAM_ADDR CFG_IMMR
|
|
#define CFG_INIT_RAM_END 0x4000 /* End of used area in DPRAM */
|
|
#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
|
|
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
|
|
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
|
|
|
|
|
|
/* Use this HRCW for booting from address 0xfe00000 (JP3 in setting 1-2) */
|
|
/* 0x0EB2B645 */
|
|
#define CFG_HRCW_MASTER (( HRCW_BPS11 | HRCW_CIP ) |\
|
|
( HRCW_L2CPC10 | HRCW_DPPC11 | HRCW_ISB010 ) |\
|
|
( HRCW_BMS | HRCW_MMR11 | HRCW_LBPC01 | HRCW_APPC10 ) |\
|
|
( HRCW_CS10PC01 | HRCW_MODCK_H0101 ) \
|
|
)
|
|
|
|
/* Use this HRCW for booting from address 0xfff0000 (JP3 in setting 2-3) */
|
|
/* #define CFG_HRCW_MASTER 0x0cb23645 */
|
|
|
|
/* This value should actually be situated in the first 256 bytes of the FLASH
|
|
which on the standard MPC8266ADS board is at address 0xFF800000
|
|
The linker script places it at 0xFFF00000 instead.
|
|
|
|
It still works, however, as long as the ADS board jumper JP3 is set to
|
|
position 2-3 so the board is using the BCSR as Hardware Configuration Word
|
|
|
|
If you want to use the one defined here instead, ust copy the first 256 bytes from
|
|
0xfff00000 to 0xff800000 (for 8MB flash)
|
|
|
|
- Rune
|
|
|
|
*/
|
|
|
|
/* no slaves */
|
|
#define CFG_HRCW_SLAVE1 0
|
|
#define CFG_HRCW_SLAVE2 0
|
|
#define CFG_HRCW_SLAVE3 0
|
|
#define CFG_HRCW_SLAVE4 0
|
|
#define CFG_HRCW_SLAVE5 0
|
|
#define CFG_HRCW_SLAVE6 0
|
|
#define CFG_HRCW_SLAVE7 0
|
|
|
|
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
|
|
#define BOOTFLAG_WARM 0x02 /* Software reboot */
|
|
|
|
#define CFG_MONITOR_BASE TEXT_BASE
|
|
#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
|
|
# define CFG_RAMBOOT
|
|
#endif
|
|
|
|
#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
|
|
#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
|
|
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
|
|
|
|
#ifndef CFG_RAMBOOT
|
|
# define CFG_ENV_IS_IN_FLASH 1
|
|
# define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
|
|
# define CFG_ENV_SECT_SIZE 0x40000
|
|
#else
|
|
# define CFG_ENV_IS_IN_NVRAM 1
|
|
# define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
|
|
# define CFG_ENV_SIZE 0x200
|
|
#endif /* CFG_RAMBOOT */
|
|
|
|
|
|
#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */
|
|
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
|
|
# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
|
|
#endif
|
|
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* HIDx - Hardware Implementation-dependent Registers 2-11
|
|
*-----------------------------------------------------------------------
|
|
* HID0 also contains cache control - initially enable both caches and
|
|
* invalidate contents, then the final state leaves only the instruction
|
|
* cache enabled. Note that Power-On and Hard reset invalidate the caches,
|
|
* but Soft reset does not.
|
|
*
|
|
* HID1 has only read-only information - nothing to set.
|
|
*/
|
|
/*#define CFG_HID0_INIT 0 */
|
|
#define CFG_HID0_INIT (HID0_ICE |\
|
|
HID0_DCE |\
|
|
HID0_ICFI |\
|
|
HID0_DCI |\
|
|
HID0_IFEM |\
|
|
HID0_ABE)
|
|
|
|
#define CFG_HID0_FINAL (HID0_ICE | HID0_IFEM | HID0_ABE )
|
|
|
|
#define CFG_HID2 0
|
|
|
|
#define CFG_SYPCR 0xFFFFFFC3
|
|
#define CFG_BCR 0x004C0000
|
|
#define CFG_SIUMCR 0x4E64C000
|
|
#define CFG_SCCR 0x00000000
|
|
|
|
/* local bus memory map
|
|
*
|
|
* 0x00000000-0x03FFFFFF 64MB SDRAM
|
|
* 0x80000000-0x9FFFFFFF 512MB outbound prefetchable PCI memory window
|
|
* 0xA0000000-0xBFFFFFFF 512MB outbound non-prefetchable PCI memory window
|
|
* 0xF0000000-0xF001FFFF 128KB MPC8266 internal memory
|
|
* 0xF4000000-0xF7FFFFFF 64MB outbound PCI I/O window
|
|
* 0xF8000000-0xF8007FFF 32KB BCSR
|
|
* 0xF8100000-0xF8107FFF 32KB ATM UNI
|
|
* 0xF8200000-0xF8207FFF 32KB PCI interrupt controller
|
|
* 0xF8300000-0xF8307FFF 32KB EEPROM
|
|
* 0xFE000000-0xFFFFFFFF 32MB flash
|
|
*/
|
|
#define CFG_BR0_PRELIM 0xFE001801 /* flash */
|
|
#define CFG_OR0_PRELIM 0xFE000836
|
|
#define CFG_BR1_PRELIM (CFG_BCSR | 0x1801) /* BCSR */
|
|
#define CFG_OR1_PRELIM 0xFFFF8010
|
|
#define CFG_BR4_PRELIM 0xF8300801 /* EEPROM */
|
|
#define CFG_OR4_PRELIM 0xFFFF8846
|
|
#define CFG_BR5_PRELIM 0xF8100801 /* PM5350 ATM UNI */
|
|
#define CFG_OR5_PRELIM 0xFFFF8E36
|
|
#define CFG_BR8_PRELIM (CFG_PCI_INT | 0x1801) /* PCI interrupt controller */
|
|
#define CFG_OR8_PRELIM 0xFFFF8010
|
|
|
|
#define CFG_RMR 0x0001
|
|
#define CFG_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
|
|
#define CFG_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
|
|
#define CFG_RCCR 0
|
|
#define CFG_MPTPR 0x00001900
|
|
#define CFG_PSRT 0x00000021
|
|
|
|
/* This address must not exist */
|
|
#define CFG_RESET_ADDRESS 0xFCFFFF00
|
|
|
|
/* PCI Memory map (if different from default map */
|
|
#define CFG_PCI_SLV_MEM_LOCAL CFG_SDRAM_BASE /* Local base */
|
|
#define CFG_PCI_SLV_MEM_BUS 0x00000000 /* PCI base */
|
|
#define CFG_PICMR0_MASK_ATTRIB (PICMR_MASK_512MB | PICMR_ENABLE | \
|
|
PICMR_PREFETCH_EN)
|
|
|
|
/*
|
|
* These are the windows that allow the CPU to access PCI address space.
|
|
* All three PCI master windows, which allow the CPU to access PCI
|
|
* prefetch, non prefetch, and IO space (see below), must all fit within
|
|
* these windows.
|
|
*/
|
|
|
|
/* PCIBR0 */
|
|
#define CFG_PCI_MSTR0_LOCAL 0x80000000 /* Local base */
|
|
#define CFG_PCIMSK0_MASK PCIMSK_1GB /* Size of window */
|
|
/* PCIBR1 */
|
|
#define CFG_PCI_MSTR1_LOCAL 0xF4000000 /* Local base */
|
|
#define CFG_PCIMSK1_MASK PCIMSK_64MB /* Size of window */
|
|
|
|
/*
|
|
* Master window that allows the CPU to access PCI Memory (prefetch).
|
|
* This window will be setup with the first set of Outbound ATU registers
|
|
* in the bridge.
|
|
*/
|
|
|
|
#define CFG_PCI_MSTR_MEM_LOCAL 0x80000000 /* Local base */
|
|
#define CFG_PCI_MSTR_MEM_BUS 0x80000000 /* PCI base */
|
|
#define CFG_CPU_PCI_MEM_START PCI_MSTR_MEM_LOCAL
|
|
#define CFG_PCI_MSTR_MEM_SIZE 0x20000000 /* 512MB */
|
|
#define CFG_POCMR0_MASK_ATTRIB (POCMR_MASK_512MB | POCMR_ENABLE | POCMR_PREFETCH_EN)
|
|
|
|
/*
|
|
* Master window that allows the CPU to access PCI Memory (non-prefetch).
|
|
* This window will be setup with the second set of Outbound ATU registers
|
|
* in the bridge.
|
|
*/
|
|
|
|
#define CFG_PCI_MSTR_MEMIO_LOCAL 0xA0000000 /* Local base */
|
|
#define CFG_PCI_MSTR_MEMIO_BUS 0xA0000000 /* PCI base */
|
|
#define CFG_CPU_PCI_MEMIO_START PCI_MSTR_MEMIO_LOCAL
|
|
#define CFG_PCI_MSTR_MEMIO_SIZE 0x20000000 /* 512MB */
|
|
#define CFG_POCMR1_MASK_ATTRIB (POCMR_MASK_512MB | POCMR_ENABLE)
|
|
|
|
/*
|
|
* Master window that allows the CPU to access PCI IO space.
|
|
* This window will be setup with the third set of Outbound ATU registers
|
|
* in the bridge.
|
|
*/
|
|
|
|
#define CFG_PCI_MSTR_IO_LOCAL 0xF4000000 /* Local base */
|
|
#define CFG_PCI_MSTR_IO_BUS 0xF4000000 /* PCI base */
|
|
#define CFG_CPU_PCI_IO_START PCI_MSTR_IO_LOCAL
|
|
#define CFG_PCI_MSTR_IO_SIZE 0x04000000 /* 64MB */
|
|
#define CFG_POCMR2_MASK_ATTRIB (POCMR_MASK_64MB | POCMR_ENABLE | POCMR_PCI_IO)
|
|
|
|
/*
|
|
* JFFS2 partitions
|
|
*
|
|
*/
|
|
/* No command line, one static partition, whole device */
|
|
#undef CONFIG_JFFS2_CMDLINE
|
|
#define CONFIG_JFFS2_DEV "nor0"
|
|
#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
|
|
#define CONFIG_JFFS2_PART_OFFSET 0x00000000
|
|
|
|
/* mtdparts command line support */
|
|
/*
|
|
#define CONFIG_JFFS2_CMDLINE
|
|
#define MTDIDS_DEFAULT ""
|
|
#define MTDPARTS_DEFAULT ""
|
|
*/
|
|
|
|
#endif /* __CONFIG_H */
|