mirror of
https://github.com/u-boot/u-boot.git
synced 2024-11-29 15:43:44 +08:00
056fbc73d5
This patch added support for accessing dual memories in parallel connection with single chipselect line from controller. For more info - see doc/SPI/README.dual-flash Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
93 lines
4.0 KiB
Plaintext
93 lines
4.0 KiB
Plaintext
SPI/QSPI Dual flash connection modes:
|
|
=====================================
|
|
|
|
This describes how SPI/QSPI flash memories are connected to a given
|
|
controller in a single chip select line.
|
|
|
|
Current spi_flash framework supports, single flash memory connected
|
|
to a given controller with single chip select line, but there are some
|
|
hw logics(ex: xilinx zynq qspi) that describes two/dual memories are
|
|
connected with a single chip select line from a controller.
|
|
|
|
"dual_flash" from include/spi.h describes these types of connection mode
|
|
|
|
Possible connections:
|
|
--------------------
|
|
SF_SINGLE_FLASH:
|
|
- single spi flash memory connected with single chip select line.
|
|
|
|
+------------+ CS +---------------+
|
|
| |----------------------->| |
|
|
| Controller | I0[3:0] | Flash memory |
|
|
| SPI/QSPI |<======================>| (SPI/QSPI) |
|
|
| | CLK | |
|
|
| |----------------------->| |
|
|
+------------+ +---------------+
|
|
|
|
SF_DUAL_STACKED_FLASH:
|
|
- dual spi/qspi flash memories are connected with a single chipselect
|
|
line and these two memories are operating stacked fasion with shared buses.
|
|
- xilinx zynq qspi controller has implemented this feature [1]
|
|
|
|
+------------+ CS +---------------+
|
|
| |---------------------->| |
|
|
| | I0[3:0] | Upper Flash |
|
|
| | +=========>| memory |
|
|
| | | CLK | (SPI/QSPI) |
|
|
| | | +---->| |
|
|
| Controller | CS | | +---------------+
|
|
| SPI/QSPI |------------|----|---->| |
|
|
| | I0[3:0] | | | Lower Flash |
|
|
| |<===========+====|====>| memory |
|
|
| | CLK | | (SPI/QSPI) |
|
|
| |-----------------+---->| |
|
|
+------------+ +---------------+
|
|
|
|
- two memory flash devices should has same hw part attributes (like size,
|
|
vendor..etc)
|
|
- Configurations:
|
|
on LQSPI_CFG register, Enable TWO_MEM[BIT:30] on LQSPI_CFG
|
|
Enable U_PAGE[BIT:28] if U_PAGE flag set - upper memory
|
|
Disable U_PAGE[BIT:28] if U_PAGE flag unset - lower memory
|
|
- Operation:
|
|
accessing memories serially like one after another.
|
|
by default, if U_PAGE is unset lower memory should accessible,
|
|
once user wants to access upper memory need to set U_PAGE.
|
|
|
|
SPI_FLASH_CONN_DUALPARALLEL:
|
|
- dual spi/qspi flash memories are connected with a single chipselect
|
|
line and these two memories are operating parallel with separate buses.
|
|
- xilinx zynq qspi controller has implemented this feature [1]
|
|
|
|
+-------------+ CS +---------------+
|
|
| |---------------------->| |
|
|
| | I0[3:0] | Upper Flash |
|
|
| |<=====================>| memory |
|
|
| | CLK | (SPI/QSPI) |
|
|
| |---------------------->| |
|
|
| Controller | CS +---------------+
|
|
| SPI/QSPI |---------------------->| |
|
|
| | I0[3:0] | Lower Flash |
|
|
| |<=====================>| memory |
|
|
| | CLK | (SPI/QSPI) |
|
|
| |---------------------->| |
|
|
+-------------+ +---------------+
|
|
|
|
- two memory flash devices should has same hw part attributes (like size,
|
|
vendor..etc)
|
|
- Configurations:
|
|
Need to enable SEP_BUS[BIT:29],TWO_MEM[BIT:30] on LQSPI_CFG register.
|
|
- Operation:
|
|
Even bits, i.e. bit 0, 2, 4 ., of a data word is located in the lower memory
|
|
and odd bits, i.e. bit 1, 3, 5, ., of a data word is located in the upper memory.
|
|
|
|
Note: Technically there is only one CS line from the controller, but
|
|
zynq qspi controller has an internal hw logic to enable additional CS
|
|
when controller is configured for dual memories.
|
|
|
|
[1] http://www.xilinx.com/support/documentation/user_guides/ug585-Zynq-7000-TRM.pdf
|
|
|
|
--
|
|
Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
|
05-01-2014.
|