mirror of
https://github.com/u-boot/u-boot.git
synced 2024-11-25 21:24:21 +08:00
1a4596601f
Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
98 lines
2.7 KiB
C
98 lines
2.7 KiB
C
/*
|
|
* (C) Copyright 2009 Stefan Roese <sr@denx.de>, DENX Software Engineering
|
|
*
|
|
* Original Author Guenter Gebhardt
|
|
* Copyright (C) 2006 Micronas GmbH
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
|
|
#include "vct.h"
|
|
|
|
int vct_ehci_hcd_init(u32 *hccr, u32 *hcor)
|
|
{
|
|
int retval;
|
|
u32 val;
|
|
u32 addr;
|
|
|
|
dcgu_set_reset_switch(DCGU_HW_MODULE_USB_24, DCGU_SWITCH_ON);
|
|
dcgu_set_reset_switch(DCGU_HW_MODULE_USB_60, DCGU_SWITCH_ON);
|
|
dcgu_set_clk_switch(DCGU_HW_MODULE_USB_24, DCGU_SWITCH_ON);
|
|
dcgu_set_clk_switch(DCGU_HW_MODULE_USB_PLL, DCGU_SWITCH_ON);
|
|
dcgu_set_reset_switch(DCGU_HW_MODULE_USB_24, DCGU_SWITCH_OFF);
|
|
|
|
/* Wait until (DCGU_USBPHY_STAT == 7) */
|
|
addr = DCGU_USBPHY_STAT(DCGU_BASE);
|
|
val = reg_read(addr);
|
|
while (val != 7)
|
|
val = reg_read(addr);
|
|
|
|
dcgu_set_clk_switch(DCGU_HW_MODULE_USB_60, DCGU_SWITCH_ON);
|
|
dcgu_set_reset_switch(DCGU_HW_MODULE_USB_60, DCGU_SWITCH_OFF);
|
|
|
|
retval = scc_reset(SCC_USB_RW, 0);
|
|
if (retval) {
|
|
printf("scc_reset(SCC_USB_RW, 0) returned: 0x%x\n", retval);
|
|
return retval;
|
|
} else {
|
|
retval = scc_reset(SCC_CPU1_SPDMA_RW, 0);
|
|
if (retval) {
|
|
printf("scc_reset(SCC_CPU1_SPDMA_RW, 0) returned: 0x%x\n",
|
|
retval);
|
|
return retval;
|
|
}
|
|
}
|
|
|
|
if (!retval) {
|
|
/*
|
|
* For the AGU bypass, where the SCC client provides full
|
|
* physical address
|
|
*/
|
|
scc_set_usb_address_generation_mode(1);
|
|
scc_setup_dma(SCC_USB_RW, BCU_USB_BUFFER_1, DMA_LINEAR,
|
|
USE_NO_FH, DMA_READ, 0);
|
|
scc_setup_dma(SCC_CPU1_SPDMA_RW, BCU_USB_BUFFER_1, DMA_LINEAR,
|
|
USE_NO_FH, DMA_WRITE, 0);
|
|
scc_setup_dma(SCC_USB_RW, BCU_USB_BUFFER_0, DMA_LINEAR,
|
|
USE_NO_FH, DMA_WRITE, 0);
|
|
scc_setup_dma(SCC_CPU1_SPDMA_RW, BCU_USB_BUFFER_0, DMA_LINEAR,
|
|
USE_NO_FH, DMA_READ, 0);
|
|
|
|
/* Enable memory interface */
|
|
scc_enable(SCC_USB_RW, 1);
|
|
|
|
/* Start (start_cmd=0) DMAs */
|
|
scc_dma_cmd(SCC_USB_RW, DMA_START, 0, DMA_READ);
|
|
scc_dma_cmd(SCC_USB_RW, DMA_START, 0, DMA_WRITE);
|
|
} else {
|
|
printf("Cannot configure USB memory channel.\n");
|
|
printf("USB can not access RAM. SCC configuration failed.\n");
|
|
return retval;
|
|
}
|
|
|
|
/* Wait a short while */
|
|
udelay(300000);
|
|
|
|
reg_write(USBH_BURSTSIZE(USBH_BASE), 0x00001c1c);
|
|
|
|
/* Set EHCI structures and DATA in RAM */
|
|
reg_write(USBH_USBHMISC(USBH_BASE), 0x00840003);
|
|
/* Set USBMODE to bigendian and set host mode */
|
|
reg_write(USBH_USBMODE(USBH_BASE), 0x00000007);
|
|
|
|
/*
|
|
* USBH_BURSTSIZE MUST EQUAL 0x00001c1c in order for
|
|
* 512 byte USB transfers on the bulk pipe to work properly.
|
|
* Set USBH_BURSTSIZE to 0x00001c1c
|
|
*/
|
|
reg_write(USBH_BURSTSIZE(USBH_BASE), 0x00001c1c);
|
|
|
|
/* Insert access register addresses */
|
|
*hccr = REG_GLOBAL_START_ADDR + USBH_CAPLENGTH(USBH_BASE);
|
|
*hcor = REG_GLOBAL_START_ADDR + USBH_USBCMD(USBH_BASE);
|
|
|
|
return 0;
|
|
}
|