mirror of
https://github.com/u-boot/u-boot.git
synced 2024-11-25 13:14:19 +08:00
ebb73de168
The original bootcount methods do not provide an interface to DM and rely on a static configuration for I2C devices (e.g. bus, chip-addr, etc. are configured through defines statically). On a modern system that exposes multiple devices in a DTS-configurable way, this is less than optimal and a interface to DM-based devices will be desirable. This adds a simple driver that is DM-aware and configurable via DTS. If ambiguous (i.e. multiple bootcount-devices are present) the /chosen/u-boot,bootcount-device property can be used to select one bootcount device. Initially, this provides support for the following DM devices: * RTC devices Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
137 lines
3.7 KiB
Plaintext
137 lines
3.7 KiB
Plaintext
The chosen node
|
|
---------------
|
|
The chosen node does not represent a real device, but serves as a place
|
|
for passing data like which serial device to used to print the logs etc
|
|
|
|
|
|
stdout-path property
|
|
--------------------
|
|
Device trees may specify the device to be used for boot console output
|
|
with a stdout-path property under /chosen.
|
|
|
|
Example
|
|
-------
|
|
/ {
|
|
chosen {
|
|
stdout-path = "/serial@f00:115200";
|
|
};
|
|
|
|
serial@f00 {
|
|
compatible = "vendor,some-uart";
|
|
reg = <0xf00 0x10>;
|
|
};
|
|
};
|
|
|
|
tick-timer property
|
|
-------------------
|
|
In a system there are multiple timers, specify which timer to be used
|
|
as the tick-timer. Earlier it was hardcoded in the timer driver now
|
|
since device tree has all the timer nodes. Specify which timer to be
|
|
used as tick timer.
|
|
|
|
Example
|
|
-------
|
|
/ {
|
|
chosen {
|
|
tick-timer = "/timer2@f00";
|
|
};
|
|
|
|
timer2@f00 {
|
|
compatible = "vendor,some-timer";
|
|
reg = <0xf00 0x10>;
|
|
};
|
|
};
|
|
|
|
u-boot,bootcount-device property
|
|
--------------------------------
|
|
|
|
In a DM-based system, the bootcount may be stored in a device known to
|
|
the DM framework (e.g. in a battery-backed SRAM area within a RTC
|
|
device) managed by a device conforming to UCLASS_BOOTCOUNT. If
|
|
multiple such devices are present in a system concurrently, then the
|
|
u-boot,bootcount-device property can select the preferred target.
|
|
|
|
Example
|
|
-------
|
|
/ {
|
|
chosen {
|
|
u-boot,bootcount-device = &bootcount-rv3029;
|
|
};
|
|
|
|
bootcount-rv3029: bootcount@0 {
|
|
compatible = "u-boot,bootcount-rtc";
|
|
rtc = &rv3029;
|
|
offset = <0x38>;
|
|
};
|
|
|
|
i2c2 {
|
|
rv3029: rtc@56 {
|
|
compatible = "mc,rv3029";
|
|
reg = <0x56>;
|
|
};
|
|
};
|
|
};
|
|
|
|
u-boot,spl-boot-order property
|
|
------------------------------
|
|
|
|
In a system using an SPL stage and having multiple boot sources
|
|
(e.g. SPI NOR flash, on-board eMMC and a removable SD-card), the boot
|
|
device may be probed by reading the image and verifying an image
|
|
signature.
|
|
|
|
If the SPL is configured through the device-tree, the boot-order can
|
|
be configured with the spl-boot-order property under the /chosen node.
|
|
Each list element of the property should specify a device to be probed
|
|
in the order they are listed: references (i.e. implicit paths), a full
|
|
path or an alias is expected for each entry.
|
|
|
|
A special specifier "same-as-spl" can be used at any position in the
|
|
boot-order to direct U-Boot to insert the device the SPL was booted
|
|
from there. Whether this is indeed inserted or silently ignored (if
|
|
it is not supported on any given SoC/board or if the boot-device is
|
|
not available to continue booting from) is implementation-defined.
|
|
Note that if "same-as-spl" expands to an actual node for a given
|
|
board, the corresponding node may appear multiple times in the
|
|
boot-order (as there currently exists no mechanism to suppress
|
|
duplicates from the list).
|
|
|
|
Example
|
|
-------
|
|
/ {
|
|
chosen {
|
|
u-boot,spl-boot-order = "same-as-spl", &sdmmc, "/sdhci@fe330000";
|
|
};
|
|
};
|
|
|
|
u-boot,spl-boot-device property
|
|
-------------------------------
|
|
|
|
This property is a companion-property to the u-boot,spl-boot-order and
|
|
will be injected automatically by the SPL stage to notify a later stage
|
|
of where said later stage was booted from.
|
|
|
|
You should not define this property yourself in the device-tree, as it
|
|
may be overwritten without warning.
|
|
|
|
firmware-loader property
|
|
------------------------
|
|
Multiple file system firmware loader nodes could be defined in device trees for
|
|
multiple storage type and their default partition, then a property
|
|
"firmware-loader" can be used to pass default firmware loader
|
|
node(default storage type) to the firmware loader driver.
|
|
|
|
Example
|
|
-------
|
|
/ {
|
|
chosen {
|
|
firmware-loader = &fs_loader0;
|
|
};
|
|
|
|
fs_loader0: fs-loader@0 {
|
|
u-boot,dm-pre-reloc;
|
|
compatible = "u-boot,fs-loader";
|
|
phandlepart = <&mmc 1>;
|
|
};
|
|
};
|