mirror of
https://github.com/u-boot/u-boot.git
synced 2024-12-23 11:43:26 +08:00
a09fea1d28
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
63 lines
1.5 KiB
C
63 lines
1.5 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* (C) Copyright 2013
|
|
* Texas Instruments Incorporated.
|
|
* Sricharan R <r.sricharan@ti.com>
|
|
*
|
|
* Configuration settings for the TI EVM5430 board.
|
|
* See ti_omap5_common.h for omap5 common settings.
|
|
*/
|
|
|
|
#ifndef __CONFIG_OMAP5_EVM_H
|
|
#define __CONFIG_OMAP5_EVM_H
|
|
|
|
#include <environment/ti/dfu.h>
|
|
|
|
#ifndef CONFIG_SPL_BUILD
|
|
/* Define the default GPT table for eMMC */
|
|
#define PARTS_DEFAULT \
|
|
"uuid_disk=${uuid_gpt_disk};" \
|
|
"name=rootfs,start=2MiB,size=-,uuid=${uuid_gpt_rootfs}"
|
|
#endif
|
|
|
|
#define DFUARGS \
|
|
"dfu_bufsiz=0x10000\0" \
|
|
DFU_ALT_INFO_MMC \
|
|
DFU_ALT_INFO_EMMC \
|
|
DFU_ALT_INFO_RAM
|
|
|
|
#include <configs/ti_omap5_common.h>
|
|
|
|
#define CONFIG_SYS_NS16550_COM3 UART3_BASE
|
|
|
|
/* MMC ENV related defines */
|
|
#define CONFIG_SYS_MMC_ENV_DEV 1 /* SLOT2: eMMC(1) */
|
|
|
|
/* Enhance our eMMC support / experience. */
|
|
#define CONFIG_HSMMC2_8BIT
|
|
|
|
/* Required support for the TCA642X GPIO we have on the uEVM */
|
|
#define CONFIG_TCA642X
|
|
#define CONFIG_SYS_I2C_TCA642X_BUS_NUM 4
|
|
#define CONFIG_SYS_I2C_TCA642X_ADDR 0x22
|
|
|
|
/* USB UHH support options */
|
|
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
|
|
|
|
#define CONFIG_OMAP_EHCI_PHY2_RESET_GPIO 80
|
|
#define CONFIG_OMAP_EHCI_PHY3_RESET_GPIO 79
|
|
|
|
/* Enabled commands */
|
|
|
|
/* USB Networking options */
|
|
|
|
#define CONSOLEDEV "ttyS2"
|
|
|
|
#define CONFIG_SCSI_AHCI_PLAT
|
|
#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
|
|
#define CONFIG_SYS_SCSI_MAX_LUN 1
|
|
#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
|
|
CONFIG_SYS_SCSI_MAX_LUN)
|
|
|
|
#endif /* __CONFIG_OMAP5_EVM_H */
|