mirror of
https://github.com/u-boot/u-boot.git
synced 2024-11-23 20:24:26 +08:00
a187559e3d
Correct spelling of "U-Boot" shall be used in all written text (documentation, comments in source files etc.). Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Heiko Schocher <hs@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
226 lines
6.1 KiB
Plaintext
226 lines
6.1 KiB
Plaintext
Motorola MPC85xxCDS boards
|
|
--------------------------
|
|
|
|
The CDS family of boards consists of a PCI backplane called the
|
|
"Arcadia", a PCI-form-factor carrier card that plugs into a PCI slot,
|
|
and a CPU daughter card that bolts onto the daughter card.
|
|
|
|
Much of the content of the README.mpc85xxads for the 85xx ADS boards
|
|
applies to the 85xx CDS boards as well. In particular the toolchain,
|
|
the switch nomenclature, and the basis for the memory map. There are
|
|
some differences, though.
|
|
|
|
|
|
Building U-Boot
|
|
---------------
|
|
|
|
The Binutils in current ELDK toolchain will not support MPC85xx
|
|
chip. You need to use binutils-2.14.tar.bz2 (or newer) from
|
|
http://ftp.gnu.org/gnu/binutils.
|
|
|
|
The 85xx CDS code base is known to compile using:
|
|
gcc (GCC) 3.2.2 20030217 (Yellow Dog Linux 3.0 3.2.2-2a)
|
|
|
|
|
|
Memory Map
|
|
----------
|
|
|
|
The memory map for U-Boot and linux has been extended w.r.t. the ADS
|
|
platform to allow for utilization of all 85xx CDS devices. The memory
|
|
map is setup for linux to operate properly. The linux source when
|
|
configured for MPC85xx CDS has been updated to reflect the new memory
|
|
map.
|
|
|
|
The mapping is:
|
|
|
|
0x0000_0000 0x7fff_ffff DDR 2G
|
|
0x8000_0000 0x9fff_ffff PCI1 MEM 512M
|
|
0xa000_0000 0xbfff_ffff PCI2 MEM 512M
|
|
0xe000_0000 0xe00f_ffff CCSR 1M
|
|
0xe200_0000 0xe2ff_ffff PCI1 IO 16M
|
|
0xe300_0000 0xe3ff_ffff PCI2 IO 16M
|
|
0xf000_0000 0xf7ff_ffff SDRAM 128M
|
|
0xf800_0000 0xf80f_ffff NVRAM/CADMUS (*) 1M
|
|
0xff00_0000 0xff7f_ffff FLASH (2nd bank) 8M
|
|
0xff80_0000 0xffff_ffff FLASH (boot bank) 8M
|
|
|
|
(*) The system control registers (CADMUS) start at offset 0xfdb0_4000
|
|
within the NVRAM/CADMUS region of memory.
|
|
|
|
|
|
Using Flash
|
|
-----------
|
|
|
|
The CDS board has two flash banks, each 8MB in size (2^23 = 0x00800000).
|
|
There is a switch which allows the boot-bank to be selected. The switch
|
|
settings for updating flash are given below.
|
|
|
|
The U-Boot commands for copying the boot-bank into the secondary bank are
|
|
as follows:
|
|
|
|
erase ff780000 ff7fffff
|
|
cp.b fff80000 ff780000 80000
|
|
|
|
|
|
U-Boot/kermit commands for downloading an image, then copying
|
|
it into the secondary bank:
|
|
|
|
loadb
|
|
[Drop to kermit:
|
|
^\c
|
|
send <u-boot-bin-image>
|
|
c
|
|
]
|
|
|
|
erase ff780000 ff7fffff
|
|
cp.b $loadaddr ff780000 80000
|
|
|
|
|
|
U-Boot commands for downloading an image via tftp and flashing
|
|
it into the second bank:
|
|
|
|
tftp 10000 <u-boot.bin.image>
|
|
erase ff780000 ff7fffff
|
|
cp.b 10000 ff780000 80000
|
|
|
|
|
|
After copying the image into the second bank of flash, be sure to toggle
|
|
SW2[2] on the carrier card before resetting the board in order to set the
|
|
secondary bank as the boot-bank.
|
|
|
|
|
|
Carrier Board Switches
|
|
----------------------
|
|
|
|
As a reminder, you should read the README.mpc85xxads too.
|
|
|
|
Most switches on the carrier board should not be changed. The only
|
|
user-settable switches on the carrier board are used to configure
|
|
the flash banks and determining the PCI slot.
|
|
|
|
The first two bits of SW2 control how flash is used on the board:
|
|
|
|
12345678
|
|
--------
|
|
SW2=00XXXXXX FLASH: Boot bank 1, bank 2 available.
|
|
01XXXXXX FLASH: Boot bank 2, bank 1 available (swapped).
|
|
10XXXXXX FLASH: Boot promjet, bank 1 available
|
|
11XXXXXX FLASH: Boot promjet, bank 2 available
|
|
|
|
The boot bank is always mapped to FF80_0000 and listed first by
|
|
the "flinfo" command. The secondary bank is always FF00_0000.
|
|
|
|
When using PCI, linux needs to know to which slot the CDS carrier is
|
|
connected.. By convention, the user-specific bits of SW2 are used to
|
|
convey this information:
|
|
|
|
12345678
|
|
--------
|
|
SW2=xxxxxx00 PCI SLOT INFORM: The CDS carrier is in slot0 of the Arcadia
|
|
xxxxxx01 PCI SLOT INFORM: The CDS carrier is in slot1 of the Arcadia
|
|
xxxxxx10 PCI SLOT INFORM: The CDS carrier is in slot2 of the Arcadia
|
|
xxxxxx11 PCI SLOT INFORM: The CDS carrier is in slot3 of the Arcadia
|
|
|
|
These are cleverly, er, clearly silkscreened as Slot 1 through 4,
|
|
respectively, on the Arcadia near the support posts.
|
|
|
|
|
|
The default setting of all switches on the carrier board is:
|
|
|
|
12345678
|
|
--------
|
|
SW1=01101100
|
|
SW2=0x1111yy x=Flash bank, yy=PCI slot
|
|
SW3=11101111
|
|
SW4=10001000
|
|
|
|
|
|
8555/41 CPU Card Switches
|
|
-------------------------
|
|
|
|
Most switches on the CPU Card should not be changed. However, the
|
|
frequency can be changed by setting SW3:
|
|
|
|
12345678
|
|
--------
|
|
SW3=XX00XXXX == CORE:CCB 2:1
|
|
XX01XXXX == CORE:CCB 5:2
|
|
XX10XXXX == CORE:CCB 3:1
|
|
XX11XXXX == CORE:CCB 7:2
|
|
XXXX1000 == CCB:SYSCLK 8:1
|
|
XXXX1010 == CCB:SYSCLK 10:1
|
|
|
|
A safe default setting for all switches on the CPU board is:
|
|
|
|
12345678
|
|
--------
|
|
SW1=10001111
|
|
SW2=01000111
|
|
SW3=00001000
|
|
SW4=11111110
|
|
|
|
|
|
8548 CPU Card Switches
|
|
----------------------
|
|
And, just to be confusing, in this set of switches:
|
|
|
|
ON = 1
|
|
OFF = 0
|
|
|
|
Default
|
|
SW1=11111101
|
|
SW2=10011111
|
|
SW3=11001000 (8X) (2:1)
|
|
SW4=11110011
|
|
|
|
SW3=X000XXXX == CORE:CCB 4:1
|
|
X001XXXX == CORE:CCB 9:2
|
|
X010XXXX == CORE:CCB 1:1
|
|
X011XXXX == CORE:CCB 3:2
|
|
X100XXXX == CORE:CCB 2:1
|
|
X101XXXX == CORE:CCB 5:2
|
|
X110XXXX == CORE:CCB 3:1
|
|
X111XXXX == CORE:CCB 7:2
|
|
XXXX0000 == CCB:SYSCLK 16:1
|
|
XXXX0001 == RESERVED
|
|
XXXX0010 == CCB:SYSCLK 2:1
|
|
XXXX0011 == CCB:SYSCLK 3:1
|
|
XXXX0100 == CCB:SYSCLK 4:1
|
|
XXXX0101 == CCB:SYSCLK 5:1
|
|
XXXX0110 == CCB:SYSCLK 6:1
|
|
XXXX0111 == RESERVED
|
|
XXXX1000 == CCB:SYSCLK 8:1
|
|
XXXX1001 == CCB:SYSCLK 9:1
|
|
XXXX1010 == CCB:SYSCLK 10:1
|
|
XXXX1011 == RESERVED
|
|
XXXX1100 == CCB:SYSCLK 12:1
|
|
XXXX1101 == CCB:SYSCLK 20:1
|
|
XXXX1110 == RESERVED
|
|
XXXX1111 == RESERVED
|
|
|
|
|
|
eDINK Info
|
|
----------
|
|
|
|
One bank of flash may contain an eDINK image.
|
|
|
|
Memory Map:
|
|
|
|
CCSRBAR @ 0xe0000000
|
|
Flash Bank 1 @ 0xfe000000
|
|
Flash Bank 2 @ 0xff000000
|
|
Ram @ 0
|
|
|
|
Commands for downloading a U-Boot image to memory from edink:
|
|
|
|
env -c
|
|
time -s 4/8/2004 4:30p
|
|
dl -k -b -o 100000
|
|
[Drop to kermit:
|
|
^\c
|
|
transmit /binary <u-boot-bin-image>
|
|
c
|
|
]
|
|
|
|
fu -l 100000 fe780000 80000
|