Blocksize was hardcoded to 512 bytes. But the blocksize varies
depeding on various mmc subsystem commands (between 8 and 512).
This hardcoding was resulting in interrupt error during data
transfer.
It is now calculated based upon the request sent by mmc subsystem.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Use get_timer() the same way as drivers/net/ftgmac100.c
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Reviewed-by: Macpaul Lin <macpaul@gmail.com>
Tested-by: Macpaul Lin <macpaul@gmail.com>
- Timeout counter value is set as DTOCV bits in SYSCTL register
For counter value set as timeout,
Timeout period = (2^(timeout + 13)) SD Clock cycles
- As per 4.6.2.2 section of SD Card specification v2.00, host should
cofigure timeout period value to minimum 0.25 sec.
- Number of SD Clock cycles for 0.25sec should be minimum
(SD Clock/sec * 0.25 sec) SD Clock cycles
= (mmc->tran_speed * 1/4) SD Clock cycles
- Calculating timeout based on
(2^(timeout + 13)) >= mmc->tran_speed * 1/4
Taking log2 both the sides and rounding up to next power of 2
=> timeout + 13 = log2(mmc->tran_speed/4) + 1
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We had an extra '0x' in the output of the LAWAR header that would cause
output like:
LAWBAR11: 0x00000000 LAWAR0x11: 0x80f0001d
intead of:
LAWBAR11: 0x00000000 LAWAR11: 0x80f0001d
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add waiting for receiving Ethernet gadget state on the Windows host
side before dropping pullup, but keep it for debug.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Port USB gadget RNDIS protocol support from linux-2.6.26
(.27 gadget stack actually has composite drivers).
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Disconnecting USB gadget with pending interrupt may cause its wrong
handling in the next time when interface will be started again
(especially actual for RNDIS). This interrupt may force the gadget
to queue unexpected response before setup stage.
Despite the fact that such interrupt handled after dropped pullup
also may add pending response, this will not bring to any issues due to
usb_ep_disable (which clears the queue) called on gadget unregistering.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
This adds support for using USB Ethernet dongles in host mode. This is just
the framework - drivers will come later. A new config option called
CONFIG_USB_HOST_ETHER can be defined in board config files to switch this
on.
The was originally written by NVIDIA and was cleaned up for release by the
Chromium authors.
Signed-off-by: Simon Glass <sjg@chromium.org>
Changed both to use a common timeout for URB submission, since they were using
different values and EHCI's was too short.
Also fixed EHCI to actually check if urb submission succeeded, rather than
silently continuing into the weeds.
Change-Id: I7f71499ffaa05187d8e5618db2419e1606007b82
Signed-off-by: Simon Glass <sjg@chromium.org>
Added this for mmc_spi driver. Though altera spi core does not
support programmable speed. It is fixed when configured in
sopc-builder.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
Data timeout counter (SYSCTL[DTOCV]) is not reliable for values of 4, 8,
and 12. Program one more than the desired value: 4 -> 5, 8 -> 9, 12 -> 13.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some CPU needs cache handling. So this patch add the config of
CONFIG_SH_ETHER_CACHE_WRITEBACK, and it calls wback function.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Added arch/arm/cpu/arm926ejs/davinci/et1011c.c for handling
ET1011C gigabit phy. which overrides get_link_speed function
from default implementation. This enables output of 125 MHz
reference clock on SYS_CLK pin.
Signed-off-by: Prakash PM <prakash.pm@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Adds "DaVinci-EMAC" as the name of the device so that
it gets printed as "Using DaVinci-EMAC device"
during network access (dhcp, tftp) instead of empty name
in "Using" statement.This name also gets
reflected in 'ethact' env variable.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Enabling the gigabit was overwriting the
previous configuration by setting up only GIGAFORCE and
GIG bits of MAC control register.
Modified to retain previous configuration while
gigabit enabling.
Signed-off-by: Prakash PM <prakash.pm@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Added support for MMC/SD cards for Davinci. This feature is enabled by
CONFIG_DAVINCI_MMC and is dependant on CONFIG_MMC and CONFIG_GENERIC_MMC
options. This is tested on DM355 and DM365 EVMs with both the available mmc
controllers.
Signed-off-by: Alagu Sankar <alagusankar@embwise.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Drop warnings due to unused variables.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
This patch cleans driver code replacing all accesses
to registers with fixed offsets with a corresponding
structure.
Signed-off-by: Stefano Babic <sbabic@denx.de>
The MXC SPI driver didn't calculate the SPI clock up to
now and just used highest possible divider 512 for DATA
RATE in the control register. This results in very low
transfer rates.
The patch adds code to calculate and setup the SPI clock
frequency for transfers.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Stefano Babic <sbabic@denx.de>
We need to shift only one time in each cycle in the swapping loop
for unaligned tx case. Currently two byte shift operations are
performed in each loop cycle causing zero gaps in the transmited
data, so not all data scheduled for transmition is actually
transmited.
The proper swapping in unaligned rx case is missing, so add it
as we need to put the received data into the rx buffer in the
correct byte order.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>
The patch adds helper funtions for basic access to the registers
of the MC9sdz60 chip (multifunctional device with RTC and CAN) via
I2C interface.
Signed-off-by: Stefano Babic <sbabic@denx.de>
There is sporadic failures when more as one I2C slave
is on the bus and the processor tries to communicate
with more as one slave.
The problem was seen on a mx35pdk (two I2C slaves,
PMIC controller and CAN/RTC chip).
The current driver uses the IIF bit in the status register
to check if the bus is busy or not. According to the manual,
this is not correct, because the IIB bit should be checked.
Not only, to check if a transfer is finished must be checked
the ICF bit, and this is not tested at all.
This patch comes from analyse with a corresponding driver
provided by Freescale as part of the LTIB tool. Comparing
the two drivers, it appears that the current u-boot driver checks
the wrong bits, and depending on race condition, the transfer
can be successful or not.
The patch gets rid also of own debug function (DPRINTF),
replaced with the general debug().
Tested on Freescale mx35pdk.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
This driver accesses to processor's register
via __REG macros, that are removed (or are planned
to be removed) and replaced by C structures.
This patches replaces all occurrencies of __REG macros.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Make at91 header includes in soft_i2c depend only on CONFIG_AT91FAMILY
rather than individual SoCs.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Reinhard Meyer<u-boot@emk-elektronik.de>
Faraday's ftpmu010 is a power managemnet unit which support cpu
sleep and frequency scaling. It has been integrated into many SoC.
This patch also move ftpmu010 to a proper place for later enhancement.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
