This patch fixes USB storage capacity detection breakage on 64-bit systems
which arises due to 'unsigned long' length difference. Old code assumes that
to be 32 bit and breaks because of inappropriate response buffer layout.
Also this fixes a number of build warnings and changes big-endian values
treatment style to be architecture-independent
Signed-off-by: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
This commit allows xHCI to use both 64 and 32 bit memory
physical addresses depending on architecture it's being built for.
Also it makes use of readq()/writeq() on 64-bit systems
Signed-off-by: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
This patch converts USB protocol headers to use explicitly sized
fields like the rest of the code
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Signed-off-by: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Cast pointers to unsigned long instead of a sized 32-bit type to avoid
pointer to integer cast size mismatch warnings.
Cc: Tom Warren <twarren@nvidia.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Change addresses to unsigned long to be compatible with 64-bit builds.
Regardless of fixing warnings, the device is still only 32-bit capable.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Marek Vasut <marex@denx.de>
Change addresses to unsigned long to be compatible with 64-bit builds.
Regardless of fixing warnings, the device is still only 32-bit capable.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: "Łukasz Majewski" <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Mass storage is not necessary present on interface 0. This
patch allow usb_stor_scan to look in every available interface.
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Since commit 79d75d7527 (ARM: move -march=* and -mtune= options to
arch/arm/Makefile), all the Tegra boards are broken because the SPL
is built for ARMv7.
Insert Tegra-specific code to arch/arm/Makefile to set compiler
flags for an earlier ARM architecture.
Note:
The v1 patch for commit 79d75d7527 *was* correct when it was
submitted. Notice it was originally written for multi .config
configuration where Kconfig set CONFIG_CPU_V7/CONFIG_CPU_ARM720T for
Tegra U-Boot Main/SPL, respectively. But, until it was merged into
the mainline, commit e02ee2548a (kconfig: switch to single .config
configuration) had been already applied there.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Stephen Warren <swarren@nvidia.com>
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Patch e11c6c27 (arm: Allow lr to be saved by board code) introduced
a different method to return from save_boot_params(). The SPL support
for AXP has been pulled and changing to this new method is now
required for SPL to work correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Luka Perkov <luka.perkov@sartura.hr>
While testing "arc: make sure _start is in the beginning of .text
section" I haven't done proper clean-up of built binaries and so missed
another tiny bit that lead to the following error:
--->8---
LD u-boot
arc-linux-ld.bfd: cannot find arch/arc/lib/start.o
Makefile:1107: recipe for target 'u-boot' failed
make: *** [u-boot] Error 1
--->8---
Fix is trivial: put "start.o" in "extra-y".
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This consolidates the flash settings for the Integrator
and activates the new ARM flash image support for them
so images can be loaded by name from flash.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This modifies the vexpress64 Juno configuration so that
it will by default load and boot a kernel and a device tree
from the images stored in the NOR flash. When we are
at it, also define the proper command line for the Juno and
indicate that the USB stick (/dev/sda1) is the default
root file system.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ARM reference designs all use a special flash image format
that stores a footer (two versions exist) at the end of the last
erase block of the image in flash memory.
Version one of the footer is indicated by the magic number
0xA0FFFF9F at 12 bytes before the end of the flash block and
version two is indicated by the magic number 0x464F4F54 0x464C5348
(ASCII for "FLSHFOOT") in the very last 8 bytes of the erase block.
This command driver implements support for both versions of the
AFS images (the name comes from the Linux driver in drivers/mtd/afs.c)
and makes it possible to list images and load an image by name into
the memory with these commands:
afs - lists flash contents
afs load <image> - loads image to address indicated in the image
afs load <image> <addres> - loads image to a specified address
This image scheme is used on the ARM Integrator family, ARM
Versatile family, ARM RealView family (not yet supported in U-Boot)
and ARM Versatile Express family up to and including the new
Juno board for 64 bit development.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ubi check command is expected to not fail and just check whether
a volume exist or not. Currently, when a volume does not exist, the
command fails which leads to an error:
"exit not allowed from main input shell."
Use 1 to indicate that a volume does not exist. This allows to use
ubi check in an if statement, e.g.
if ubi check rootfs; then; echo "exists"; else; echo "not there"; fi
This is important to have entry point in the beginning of .text section
because it allows simple loading and execution of U-Boot.
For example pre-bootloader loads U-Boot in memory starting from offset
0x81000000 and then just jumps to the same address.
Otherwise pre-bootloader would need to find-out where entry-point is. In
its turn if it deals with binary image of U-Boot there's no way for
pre-bootloader to get required value.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Work_92105 from Work Microwave is an LPC3250-
based board with the following features:
- 64MB or 128MB SDR DRAM
- 1 GB SLC NAND, managed through MLC controller.
- Ethernet
- Ethernet + PHY SMSC8710
- I2C:
- EEPROM (24M01-compatible)
- RTC (DS1374-compatible)
- Temperature sensor (DS620)
- DACs (2 x MAX518)
- SPI (through SSP interface)
- Port expander MAX6957
- LCD display (HD44780-compatible), controlled
through the port expander and DACs
This board has SPL support, and uses the LPC32XX boot
image format.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
introduce CONFIG_SPL_PANIC_ON_RAW_IMAGE.
An SPL which define this will panic() if the
image it has loaded does not have a mkimage
signature.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
The controller's Reed-Solomon ECC hardware is
used except of course for raw reads and writes.
It covers in- and out-of-band data together.
The SPL framework is supported.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
At present Hyungwon can't take care of this board in U-Boot,
so I will keep it working.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Hyungwon Hwang <human.hwang@samsung.com>
There're 2 versions of motherboards that could be used in ARC SDP.
The only important difference for U-Boot is different NAND IC in use:
[1] v2 board (we used to support up until now) sports MT29F4G08ABADAWP
while
[2] v3 board sports MT29F4G16ABADAWP
They are almost the same except data bus width 8-bit in [1] and 16-bit
in [2]. And for proper support of 16-bit data bus we have to pass
NAND_BUSWIDTH_16 option to NAND driver core - which we do now knowing
board type we're running on.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Add support for Inverse Path USB armory board, an open source
flash-drive sized computer based on Freescale i.MX53 SoC.
http://inversepath.com/usbarmory
Signed-off-by: Andrej Rosano <andrej@inversepath.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Chris Kuethe <chris.kuethe@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
Tested-By: Vagrant Cascadian <vagrant@debian.org>
Tested-by: Chris Kuethe <chris.kuethe@gmail.com>
Move the MX5 based boards to arch/arm/cpu/armv7/mx5, following the
commit: 89ebc82137
Signed-off-by: Andrej Rosano <andrej@inversepath.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
Tested-by: Chris Kuethe <chris.kuethe@gmail.com>
Since commit 326a682358 (malloc_f: enable SYS_MALLOC_F by default
if DM is on), Zynq MMC boot hangs up after printing the following:
U-Boot SPL 2015.04-rc5-00053-gadcc570 (Apr 08 2015 - 12:59:11)
mmc boot
reading system.dtb
Prior to commit 326a682358, Zynq boards enabled CONFIG_DM, but
not CONFIG_SYS_MALLOC_F. That commit forcibly turned on
CONFIG_SYS_MALLOC_F. I have not figured out the root cause, but
anyway it looks like CONFIG_SYS_MALLOC_F gave a bad impact on the
Zynq MMC boot.
We are planning to have the v2015.04 release in a few days.
I know this is a defensive fixup, but what I can do now is to add
# CONFIG_SYS_MALLOC_F is not set
to every Zynq defconfig file to get back the original behavior.
Tested on:
- Zedboard
- ZC706 board
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Cc: Simon Glass <sjg@chromium.org>
Include/fsl_sec.h defines sec_in and sec_out, according to the
platform's endianess. Therefore, CONFIG_SYS_FSL_LE needs to be
declared in the configuration file of the target, in order to use
enable the DEK blob generation command. This requirement is not
explicit in the README.mxc_hab.
Signed-off-by: Ulises Cardenas <Ulises.Cardenas@freescale.com>
Since commit 32df39c741 ("mx5: fix get_reset_cause") we have the following
boot messages on a mx53qsb:
U-Boot 2015.04-rc5-00029-gd68df02 (Apr 06 2015 - 11:15:39)
CPU: Freescale i.MX53 rev2.1 at 800 MHz
Reset cause: POR
Board: MX53 LOCO
I2C: ready
DRAM: 1 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
CPU: Freescale i.MX53 rev2.1 at 1000 MHz
Reset cause: unknown reset
Net: FEC [PRIME]
The CPU and Reset cause lines appear twice.
Initially mx53 boots at 800MHz, then at a later point the PMIC is configured via
I2C to raise the CPU voltage so that it can run at 1GHz.
To avoid such misleading double printings, disable printing cpu info for now.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
With e37f1eb we now use strict_strtoul() in do_mem_mtest() and this
gives us a warning:
../include/vsprintf.h:38:5: note: expected 'long unsigned int *' but
argument is of type 'int *'
Signed-off-by: Tom Rini <trini@konsulko.com>
Since the Kconfig conversion, boards.cfg scanned by MAKEALL is
generated by tools/genboardscfg.py. Every board is supposed to have
its own MAINTAINERS that contains maintainer and status information,
but, in fact, MAINTAINERS is missing from some boards.
For such boards, the first field, Status, is filled with '-'.
It causes a problem for "set" command, which ignores '-' in its
arguments. Consequently, get_target_arch() returns a wrong field
and MAKEALL fails to get a correct toolchain.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since the Kconfig conversion, config.mk has been included only when
include/config/auto.conf is newer than the .config file.
It causes build error if both files have the same time-stamps.
It is actually possible because EXT* file systems have a 1s time-stamp
resolution.
The config.mk should be included when include/config/auto.conf is
*not older* than the .config file.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Tom Rini <trini@konsulko.com>
Reported-by: York Sun <yorksun@freescale.com>
Reported-by: Stephen Warren <swarren@nvidia.com>
Reported-by: Matthew Gerlach <mgerlach@opensource.altera.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
