Add support for USB-A9263 board manufactured by Calao Systems
(http://www.calao-systems.com/).
Code is based on old U-Boot sources (2010.09) released by Calao.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
enable support for the siemens AT91SAM9G20 based board corvus.
Signed-off-by: Boris Schmidt <boris.schmidt@siemens.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
enable support for the siemens AT91SAM9G20 based boards taurus
and axm.
Signed-off-by: Roger Meier <r.meier@siemens.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Phytec sells revision or version 3 of pcm051. It is labeled 1358.3 on
the board. The difference for u-boot is that is has other DDR3 RAM on it:
1 x MT41K256M16HA125E instead of 2 x MT41J256M8HX15E on revisions 1 and
2. Both configurations are 512 MiB.
Configure your u-boot build with pcm051_rev3 for the new RAM and
pcm051_rev1 for the old RAM configuration. Board revision 2 has to use
pcm051_rev1 also.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
The koelsch board has R8A7791, 2GB DDR3-SDRAM, USB,
Quad SPI, Ethernet, and more.
This patch supports the following functions:
- DDR3-SDRAM
- SCIF
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
Add the default RCW(SerDes 0x66_0x16) and PBI configure file for
T2080QDS board, so we can use PBL tool to generate the ramboot
image to support boot from NAND/SPI/SD.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
The T2080QDS is a high-performance computing evaluation, development and
test platform supporting the T2080 QorIQ Power Architecture processor.
T2080QDS feature overview
Processor:
- T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
Memory:
- Single memory controller capable of supporting DDR3 and DDR3-LV devices
- Two DDR3 DIMMs up to 4GB, Dual rank @ 2133MT/s and ECC support
Ethernet interfaces:
- Two 1Gbps RGMII on-board ports
- Four 10Gbps XFI on-board cages
- 1Gbps/2.5Gbps SGMII Riser card
- 10Gbps XAUI Riser card
Accelerator:
- DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
SerDes:
- 16 lanes up to 10.3125GHz
- Supports Aurora debug, PEX, SATA, SGMII, sRIO, HiGig, XFI and XAUI
IFC:
- 128MB NOR Flash, 512MB NAND Flash, PromJet debug port and FPGA
eSPI:
- Three SPI flash (16MB N25Q128A + 16MB EN25S64 + 512KB SST25WF040)
USB:
- Two USB2.0 ports with internal PHY (one Type-A + one micro Type-AB)
PCIE:
- Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV)
SATA:
- Two SATA 2.0 ports on-board
SRIO:
- Two Serial RapidIO 2.0 ports up to 5 GHz
eSDHC:
- Supports SD/SDHC/SDXC/eMMC Card
I2C:
- Four I2C controllers.
UART:
- Dual 4-pins UART serial ports
System Logic:
- QIXIS-II FPGA system controll
Debug Features:
- Support Legacy, COP/JTAG, Aurora, Event and EVT
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: removed Makefile blank line at EOF,
fix conflicts with moving DDR driver]
Acked-by: York Sun <yorksun@freescale.com>
T1042RDB_PI is Freescale Reference Design Board supporting the T1042
QorIQ Power Architecture™ processor. T1042 is a reduced personality
of T1040 SoC without Integrated 8-port Gigabit. The board is designed
with low power features targeted for Printing Image Market.
T1042RDB_PI is similar to T1040RDB board with few differences like
it has video interface, supports T1042 personality
T1042RDB_PI board Overview
-----------------------
- Four e5500 cores, each with a private 256 KB L2 cache
- 256 KB shared L3 CoreNet platform cache (CPC)
- Interconnect CoreNet platform
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving
support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
for the following functions:
- Packet parsing, classification, and distribution
- Queue management for scheduling, packet sequencing, and congestion
management
- Cryptography Acceleration
- RegEx Pattern Matching Acceleration
- IEEE Std 1588 support
- Hardware buffer management for buffer allocation and deallocation
- Ethernet interfaces
- Two on-board RGMII 10/100/1G ethernet ports.
- SERDES Connections, 8 lanes supporting:
— PCI
— SATA 2.0
- DDR Controller 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and
Interleaving
-IFC/Local Bus
- NAND flash: 1GB 8-bit NAND flash
- NOR: 128MB 16-bit NOR Flash
- Ethernet
- Two on-board RGMII 10/100/1G ethernet ports.
- PHY #0 remains powered up during deep-sleep
- CPLD
- Clocks
- System and DDR clock (SYSCLK, “DDRCLK”)
- SERDES clocks
- Video
- DIU supports video at up to 1280x1024x32bpp
- HDMI connector
- Power Supplies
- USB
- Supports two USB 2.0 ports with integrated PHYs
- Two type A ports with 5V@1.5A per port.
- SDHC
- SDHC/SDXC connector
- SPI
- On-board 64MB SPI flash
- I2C
- Device connected: EEPROM, thermal monitor, VID controller, RTC
- Other IO
- Two Serial ports
- ProfiBus port
- Four I2C ports
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
The MPC824x processors have long reached EOL, and the PN62 board has
not seen any board-specific updates for more than a decade. It is now
causing build issues. Instead of wasting time on things nobody is
interested in any more, we rather drop this board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
cc: Tom Rini <trini@ti.com>
Commit f6d1f6e4a5 broke selection of UARTs
other than UART0 for am335x_evm configurations by setting CONS_INDEX to
1 for all configurations. Revert the CONS_INDEX changes.
Signed-off-by: Andrew Bradford <andrew@bradfordembedded.com>
Update my email address as ti814x_evm maintainer to save
people some frustrating bounces and non-response.
Signed-off-by: Matt Porter <matt.porter@linaro.org>
Conflicts:
arch/arm/cpu/arm926ejs/mxs/Makefile
board/compulab/cm_t35/Makefile
board/corscience/tricorder/Makefile
board/ppcag/bg0900/Makefile
drivers/bootcount/Makefile
include/configs/omap4_common.h
include/configs/pdnb3.h
Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:
board/compulab/common/Makefile
board/udoo/Makefile
include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.
include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.
Note: 'git show' will also list two files just because
they are new:
include/configs/am335x_igep0033.h
include/configs/omap3_igep00x0.h
This patch adds me as a maintainer of the malta(el) board(s). I have
access to physical Malta boards and the desire for U-boot to run well on
them.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
This is in preparation for adapting this board to function correctly on
a physical MIPS Malta board. The board is moved into an "imgtec" vendor
directory at the same time in order to ready us for any other boards
supported by Imagination in the future.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Remove 'HEAD' line which is most likely left there while rebasing. It was
introduced in commit 877bfe37dc.
Signed-off-by: Luka Perkov <luka@openwrt.org>
Commit 93e14596 "Coding Style cleanup: replace leading SPACEs by TABs"
added trailing whitespace to a single line of boards.cfg. I presume this
was unintentional, and it causes the file to change after running it
through the reformat.py script. Remove the offending character.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
UART booting is supported on this SoC, but via UART3 rather than UART1.
Because of this we must change the board to use UART3 for all console
access (only one UART is exposed on this board and a slight HW mod is
required to switch UARTs).
Signed-off-by: Minal Shah <minal.shah@ti.com>
[trini: Make apply to mainline, reword commit]
Signed-off-by: Tom Rini <trini@ti.com>
The 'flashcard' u-boot configuration has a readonly environment and boots a
bare kernel/initrd to program the device from an clean environment.
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
There seems to be a naming convention for the configuration
files for boards using the same SoC family. This makes
easier to do changes that affect different boards based
on the same SoC.
Since the IGEPv2 board and the IGEP COM Module use a TI
OMAP35xx/DM37xx processor, is better to rename its board
config to use this naming scheme.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
There seems to be a naming convention for the configuration
files for boards using the same SoC family. This makes
easier to do changes that affect different boards based
on the same SoC.
Since the IGEP COM AQUILA use a TI AM335x processor is better
to rename its board config to use this naming scheme.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
This patch introduces the support for Keymile's kmp204x reference
design. This design is based on Freescale's P2040/P2041 SoC.
The peripherals used by this design are:
- DDR3 RAM with SPD support
- SPI NOR Flash as boot medium
- NAND Flash
- 2 PCIe busses (hosts 1 and 3)
- 3 FMAN Ethernet devices (FMAN1 DTSEC1/2/5)
- 3 Local Bus windows, with one dedicated to the QRIO reset/power mgmt
FPGA
- 2 HW I2C busses
- last but not least, the mandatory serial port
The board/keymile/kmp204x code is mostly based on Freescale's P2041rdb
support and was changed according to our design (that means essentially
removing what is not present on the designs and a few adaptations).
There is currently only one prototype board that is based on this design
and this patch also introduces it. The board is called kmlion1.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
kmp204x: update the ENV #define
The comments had to be refined as well as the total size
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: fix ddr.c]
Acked-by: York Sun <yorksun@freescale.com>
This board supports FEC Ethernet, SPI NOR and NAND flash.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Christoph Baumann <c.baumann@ppc-ag.de>
Add basic support for mx6q udoo board.
For further information about Udoo board:
http://www.udoo.org/
Tested booting a mainline device tree kernel and a Yocto rootfs from mmc.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Remove Prodrive pdnb3 board (including the scpu variant) support
from mainline. As its unmaintained and not needed any more for
quite some time.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Martijn de Gouw <martijn.de.gouw@prodrive.nl>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
- Rename old P1010RDB board as P1010RDB-PA.
- Add support for new P1010RDB-PB board.
- Some optimization.
For more details, see board/freescale/p1010rdb/README.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: fix conflicts in boards.cfg]
Acked-by: York Sun <yorksun@freescale.com>
T1040QDS is a high-performance computing evaluation, development and
test platform supporting the T1040 QorIQ Power Architecture™ processor.
T1040QDS board Overview
-----------------------
- Four e5500 cores, each with a private 256 KB L2 cache
- 256 KB shared L3 CoreNet platform cache (CPC)
- Interconnect CoreNet platform
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving
support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
for the following functions:
- Packet parsing, classification, and distribution
- Queue management for scheduling, packet sequencing, and congestion
management
- Cryptography Acceleration
- RegEx Pattern Matching Acceleration
- IEEE Std 1588 support
- Hardware buffer management for buffer allocation and deallocation
- Ethernet interfaces
- Integrated 8-port Gigabit Ethernet switch
- Four 1 Gbps Ethernet controllers
- SERDES Connections, 8 lanes supporting:
— PCI Express: supporting Gen 1 and Gen 2;
— SGMII
— QSGMII
— SATA 2.0
— Aurora debug with dedicated connectors
- DDR Controller 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and
Interleaving
-IFC/Local Bus
- NAND flash: 8-bit, async, up to 2GB.
- NOR: 8-bit or 16-bit, non-multiplexed, up to 512MB
- GASIC: Simple (minimal) target within Qixis FPGA
- PromJET rapid memory download support
- Ethernet
- Two on-board RGMII 10/100/1G ethernet ports.
- PHY #0 remains powered up during deep-sleep
- QIXIS System Logic FPGA
- Clocks
- System and DDR clock (SYSCLK, “DDRCLK”)
- SERDES clocks
- Power Supplies
- Video
- DIU supports video at up to 1280x1024x32bpp
- USB
- Supports two USB 2.0 ports with integrated PHYs
— Two type A ports with 5V@1.5A per port.
— Second port can be converted to OTG mini-AB
- SDHC
- SDHC port connects directly to an adapter card slot, featuring:
- Supporting SD slots for: SD, SDHC (1x, 4x, 8x) and/or MMC
— Supporting eMMC memory devices
- SPI
- On-board support of 3 different devices and sizes
- Other IO
- Two Serial ports
- ProfiBus port
- Four I2C ports
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: fix conflict in boards.cfg]
Acked-by-by: York Sun <yorksun@freescale.com>
omap1510inn is orphan and has been for years now.
Reove it and, as it was the only arm925t target,
also remove arm925t support.
Update doc/README.scrapyard accordingly.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
This patch add support for a new Samsung board Trats2.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Put all informations about targets, including state (active or
orphan) and maintainers, in boards.cfg; remove MAINTAINERS;
adjust the build system accordingly.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
Signed-off-by: Eric Jarrige <eric.jarrige@armadeus.org>
Signed-off-by: Nicolas Colombain <nicolas.colombain@armadeus.com>
Add STMP3780-based Sansa Fuze+ board. This board is a small PMP
device sporting a CPU which was later rebranded to i.MX233 .
Currently supported is USB gadget mode and MMC .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Add STMP3780-based XFi3 board. This board is a small PMP device
sporting a CPU which was later rebranded to i.MX233 . Currently
supported is USB gadget mode and both external SD and internal
Phison SD-NAND bridge .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
