The CONFIG_SPL_MAX_SIZE could be 0x27000 for i.MX8MM when SPL_TEXT_BASE
set to 0x7E1000.
The DDR firmware max uses 96KB, there is a 4KB padding header before
SPL_TEXT_BASE, so the SPL MAX SIZE is `256KB - 96KB - 4KB`.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add a basic test of the 'fdt addr' command, to kick things off.
This includes a new convenience function to run a command from a printf()
string.
Signed-off-by: Simon Glass <sjg@chromium.org>
Convert taken FPGA image "compatible" string to a binary compatible
flag and pass it to an FPGA driver.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Tested-by: Ricardo Salveti <ricardo@foundries.io>
Tested-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Link: https://lore.kernel.org/r/20220722141614.297383-9-oleksandr.suvorov@foundries.io
Signed-off-by: Michal Simek <michal.simek@amd.com>
These flags may be used to check whether an FPGA driver is able to
load a particular FPGA bitstream image.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Tested-by: Ricardo Salveti <ricardo@foundries.io>
Tested-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Link: https://lore.kernel.org/r/20220722141614.297383-7-oleksandr.suvorov@foundries.io
Signed-off-by: Michal Simek <michal.simek@amd.com>
Do not use 0 as address for memory because of the special meaning for
pointers (null pointer). Change the spl bss start address to the second
page.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Link: https://lore.kernel.org/r/20220714134733.7487-1-stefan.herbrechtsmeier-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The ISW_ENTRY_ADDR symbol was used for OMAP devices in place of
SPL_TEXT_BASE. Keystone2 HS devices were not using it right either.
Remove ISW_ENTRY_ADDR and use SPL_TEXT_BASE directly.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
SPL on mvebu loads proper U-Boot from custom Marvell kwbimage format and
therefore support for other binary formats is not required to be present in
SPL. Boot source of proper U-Boot is defined by compile time options and
therefore it is not required to enable all possible and unused peripherals
in SPL by default.
This change decrease size of SPL binaries.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Some consoles use CSI 200~ and CSI 201~ to bracket inserts. This leads
U-Boot to misinterpret the inserted string. Ignore these escape sequences.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
On probe, the SPI NOR core will put a flash in 8D mode if it
supports it. But Linux as of now expects to get the flash in
1S mode. Handing the flash to Linux in Octal DTR mode means
the kernel will fail to detect the flash.
This commit adds an option to soft reset the flash after
spl_spi_load_image() so that the flash can be reset to 1S mode
and subsequent spi-nor probe in Linux does not fail, since
spl_spi_load_image() performs spi_flash_probe() the remove is
added after completion loading images in spi_flash_probe() itself.
Tested on J721E EVM with 5.10 Linux kernel.
Linux spi-nor probe without the fix:
root@j7-evm:~# dmesg | grep spi-nor
[ 4.928023] spi-nor spi0.0: unrecognized JEDEC id bytes: ff ff ff ff ff ff
[ 4.934938] spi-nor: probe of spi0.0 failed with error -2
Linux spi-nor probe with the fix:
root@j7-evm:~# dmesg | grep spi-nor
[ 4.904484] spi-nor spi0.0: mt35xu512aba (65536 Kbytes)
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
board_usb_init() should receive the controller_index as its
first parameter instead of having it hardcoded as 0.
All in-tree users have CONFIG_SPL_SDP_USB_DEV as 0, so this error
should not affect any board.
Fix it by passing controller_index as the parameter of board_usb_init().
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
Add support to load legacy image with payload compressed. This redirects
the boot flow for all legacy images. If the payload is not compressed, the
actual behavior will remain unchanged.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
If the payload is compressed, SPL_COPY_PAYLOAD_ONLY should always be set
since the payload will not be directly read to its load address. The
payload will first be read to a temporary buffer, and then be decompressed
to its load address, without image header.
If the payload is not compressed, and SPL_COPY_PAYLOAD_ONLY is set, image
header should be skipped on loading. Otherwise image header should also be
read to its load address.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch removes the dependency to SPL_NAND_DRIVERS for SPL_NAND_BASE to
allow minimal spl nand driver to use nand base for probing NAND chips.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Introduce define for connection timeout, named HUB_DEBOUNCE_TIMEOUT
as in linux kernel drivers/usb/core/hub.c
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
For now the driver does not probe if usbkbd was not present in stdin.
This presents two issues, we can not probe the driver before setting stdin
and we can not use this driver in other manner than stdin console.
This patch fixes this by adding an else statement. It simply probes the
driver without console management in the case "usbkbd" is not in stdin.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
In case the MALLOC_F_ADDR is set to non-zero value, the early malloc area is
not going to be placed just below stack top, but elsewhere. Do not reserve
MALLOC_F bytes in this case, as that wastes stack space and may even cause
insufficient stack space in SPL.
This functionality is particularly useful on i.MX8M, where the insufficient
stack space can be triggered.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Thomas Chou <thomas@wytron.com.tw>
Cc: Tom Rini <trini@konsulko.com>
Tighten up symbol dependencies in a number of places. Ensure that a SPL
specific option has at least a direct dependency on SPL. In places
where it's clear that we depend on something more specific, use that
dependency instead. This means in a very small number of places we can
drop redundant dependencies.
Reported-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The AST2600 bootrom has a max size of 64KB. This can be overridden if the
system is running the SPL from SPI NOR and not using secure boot.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Currently the SPI flash to load from is defined through the compile
time config CONFIG_SF_DEFAULT_BUS and CONFIG_SF_DEFAULT_CS, this
prevents the loading of binaries from different SPI flash using the
same build.E.g. supporting QSPI flash boot and OSPI flash boot
on J721E platform is not possible due to this limitation.
This commit adds lookup functions spl_spi_boot_bus()
and spl_spi_boot_cs for identifying the flash device based on the
selected boot device, when not overridden the lookup functions are
weakly defined in common/spl/spl_spi.c.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Now that we have consistently named symbols to enable USB host or gadget
controller support in SPL or full U-Boot, we do not need to
unconditionally build USB files nor depend on non-SPL symbols to know
when to build these common files.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tighten up symbol dependencies in a number of places. Ensure that a VPL
specific option has at least a direct dependency on VPL. In places
where it's clear that we depend on something more specific, use that
dependency instead.
Reported-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tighten up symbol dependencies in a number of places. Ensure that a TPL
specific option has at least a direct dependency on TPL. In places
where it's clear that we depend on something more specific, use that
dependency instead.
Reported-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
We want to keep all of the default values for SPL_LDSCRIPT in the same
place both for overall clarity as well as not polluting unrelated config
files.
Signed-off-by: Tom Rini <trini@konsulko.com>
The i.MX8M boards use partially specified binman images which have an
SPL entry without a U-Boot entry. This would normally cause an error due
to the 'u_boot_any' binman symbols declared by BINMAN_UBOOT_SYMBOLS
requiring a U-Boot-like entry in the same image as the SPL.
However, a problem in the ARMv8 __image_copy_start symbol definition
effectively disables binman from attempting to write any symbols at all,
so everything appears to work fine until runtime. A future patch fixes
the issue in the linker scripts, which lets binman fill in the symbols,
which would result in the build error described above.
Explicitly disable the 'u_boot_any' symbols for i.MX8M boards. They are
already effectively unusable, and they are incompatible with the boards'
current binman image descriptions.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Binman lets us declare symbols in SPL/TPL that refer to other entries in
the same binman image as them. These symbols are filled in with the
correct values while binman assembles the images, but this is done
in-memory only. Symbols marked as optional can be filled with
BINMAN_SYM_MISSING as an error value if their referred entry is missing.
However, the unmodified SPL/TPL binaries are still available on disk,
and can be used by people. For these files, nothing ensures that the
symbols are set to this error value, and they will be considered valid
when they are not.
Empirically, all symbols show up as zero in a sandbox_vpl build when we
run e.g. tpl/u-boot-tpl directly. On the other hand, zero is a perfectly
fine value for a binman-written symbol, so we cannot say the symbols
have wrong values based on that.
Declare a magic symbol that binman always fills in with a fixed value.
Check this value as an indicator that symbols were filled in correctly.
Return the error value for all symbols when this magic symbol has the
wrong value.
For binman tests, we need to make room for the new symbol in the mocked
SPL/TPL data by extending them by four bytes. This messes up some test
image layouts. Fix the affected values, and check the magic symbol
wherever it makes sense.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
The SPL code declares binman symbols for U-Boot phases depending on
CONFIG_IS_ENABLED(BINMAN_UBOOT_SYMBOLS). This config exists for SPL and
TPL, also add a version for VPL.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Enabling CONFIG_BINMAN makes binman run after a build to package any
images specified in the device-tree. It also enables a mechanism for
SPL/TPL to declare and use special linker symbols that refer to other
entries in the same binman image. A similar feature that gets this info
from the device-tree exists for U-Boot proper, but it is gated behind a
CONFIG_BINMAN_FDT unlike the symbols.
Confusingly, CONFIG_SPL/TPL_BINMAN_SYMBOLS also exist. These configs
don't actually enable/disable the symbols mechanism as one would expect,
but declare some symbols for U-Boot using this mechanism.
Reuse the BINMAN_SYMBOLS configs to make them toggle the symbols
mechanism, and declare symbols for the U-Boot phases in a dependent
BINMAN_UBOOT_SYMBOLS config. Extend it to cover symbols of all phases.
Update the config prompt and help message to make it clearer about this.
Fix binman test binaries to work with CONFIG_IS_ENABLED(BINMAN_SYMBOLS).
Co-developed-by: Peng Fan <peng.fan@nxp.com>
[Alper: New config for phase symbols, update Kconfigs, commit message]
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
TPL_BINMAN_SYMBOLS depends on SPL_FRAMEWORK. The code this enables is
compiled by checking CONFIG_$(SPL_TPL_)FRAMEWORK, so it should depend on
TPL_FRAMEWORK instead (which in turn depends on SPL_FRAMEWORK). This was
most likely a typo due to copy-pasting the config's SPL version, fix it.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Some SPL functions directly use the binman 'u_boot_any' symbols to get
U-Boot's binman image position. These symbols are declared by the
SPL/TPL_BINMAN_SYMBOLS configs, but they are accessed by macros defined
by just CONFIG_BINMAN. So when BINMAN is enabled and BINMAN_SYMBOLS is
disabled, the code tries to use undeclared symbols and we get an error.
Therefore, any use of 'u_boot_any' symbols in the code is an implicit
dependency on SPL/TPL_BINMAN_SYMBOLS. However, in the current uses
they are meant to be the next phase's values, where that happens to be
U-Boot. In the meantime, helper funcions spl_get_image_pos/size() were
introduced to get these values.
Convert all uses of u_boot_any symbols to these functions, so we only
access these symbols at one place. Make sure they will not use these
symbols when the BINMAN_SYMBOLS configs are disabled, by returning early
in those cases.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Add an option to tell SPL to show memory usage for driver model just
before it boots into the next phase.
Signed-off-by: Simon Glass <sjg@chromium.org>
cpu:
- Add driver for microblaze cpu
net:
- Add support for DM_ETH_PHY to AXI emac and emaclite
xilinx:
- Switch platforms to DM_ETH_PHY
- DT chagnes in ZynqMP and Zynq
- Enable support for SquashFS
zynqmp:
- Add support for KR260 boards
- Move BSS from address 0
- Move platform identification from board code to soc driver
- Improve zynqmp_psu_init_minimize
versal:
- Enable loading app at EL1
serial:
- Setup default address and clock rates for DEBUG uarts
pinctrl:
- Add support for tri state and output enable properties
relocate-rela:
- Clean relocate-rela implementation for ARM64
- Add support for Microblaze
microblaze:
- Add support for runtime relocation
- Rework cache handling (wiring, Kconfig) based on cpuinfo
- Remove interrupt support
timer:
- Extract axi timer driver from Microblaze to generic location
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYrlYngAKCRDKSWXLKUoM
ITgbAJ9S9xO2QqxtuodWAYMtJfvZ14c7mgCeKnyFTrrBnJkC0wPsGqE71oNJ49o=
=3gGm
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.10' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.10
cpu:
- Add driver for microblaze cpu
net:
- Add support for DM_ETH_PHY to AXI emac and emaclite
xilinx:
- Switch platforms to DM_ETH_PHY
- DT chagnes in ZynqMP and Zynq
- Enable support for SquashFS
zynqmp:
- Add support for KR260 boards
- Move BSS from address 0
- Move platform identification from board code to soc driver
- Improve zynqmp_psu_init_minimize
versal:
- Enable loading app at EL1
serial:
- Setup default address and clock rates for DEBUG uarts
pinctrl:
- Add support for tri state and output enable properties
relocate-rela:
- Clean relocate-rela implementation for ARM64
- Add support for Microblaze
microblaze:
- Add support for runtime relocation
- Rework cache handling (wiring, Kconfig) based on cpuinfo
- Remove interrupt support
timer:
- Extract axi timer driver from Microblaze to generic location
Microblaze is using NEEDS_MANUAL_RELOC from the beginnging. This is causing
issues with function pointer arrays which need to be updated manually after
relocation. Building code with -fPIC and linking with -pic will remove this
limitation and there is no longer need to run manual update.
By default still old option is enabled but by disabling NEEDS_MANUAL_RELOC
code will be compiled for full relocation.
The patch does couple of things which are connected to each other.
- Define STATIC_RELA dependency to call relocate-rela to fill sections.
- REMAKE_ELF was already enabled but u-boot file can't be used because
sections are empty. relocate-rela will fill them and output file is
u-boot.elf which should be used.
- Add support for full relocation (u-boot.elf)
- Add support for early relocation when u-boot.bin is loaded to different
address then CONFIG_SYS_TEXT_BASE
- Add rela.dyn and dynsym sections
Disabling NEEDS_MANUAL_RELOC U-Boot size increased by 10% of it's original
size (550kB to 608kB).
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/a845670b34925859b2e321875f7588a29f6655f9.1655299267.git.michal.simek@amd.com
The bi_enetaddr field in struct bd_info is write-only; nothing ever
reads back the value.
Moreover, the value we write is more or less random, and certainly not
something one can rely on: If the board has a writable environment and
the mac address has been stored there, we fetch that value. But if the
board doesn't, this code runs before initr_net() -> eth_initialize(),
and thus before the code in eth-uclass which fetches MAC addresses
from eeprom, fuses or whatnot and populates the (run-time) environment
with those values.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Tom Rini <trini@konsulko.com>
Static events do not currently work post-relocation for boards that enable
CONFIG_NEEDS_MANUAL_RELOC. Relocate event handler pointers for all event
spies to fix this.
Tested on Microblaze.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
The whole event_register() function is wrapped in EVENT_DYNAMIC #ifdef
checks, so the inner check is not needed:
#if CONFIG_IS_ENABLED(EVENT_DYNAMIC)
...
int event_register(...)
{
...
if (!CONFIG_IS_ENABLED(EVENT_DYNAMIC))
return -ENOSYS;
}
#endif
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
- In a few places, add missing "depends on" that can be implied from the
option name (i.e. SPL_DM_xxx depends on SPL_DM).
- Make less use of "if SPL_xxx ... endif" clauses as most of the time
this reads better as depends on. In the case of UBI however, move it
all to a sub-menu.
- Rework SPL_NO_CPU_SUPPORT as it's very specific to the
non-SPL_FRAMEWORK implementation used on those platforms, and a
tangent to how CONFIG_SPL_START_S_PATH was used.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Move all PowerPC (and some shared with Layerscape) options to
common/spl/Kconfig.nxp
- Move all other TPL related options to common/spl/Kconfig.tpl
- Move all VPL related options to common/spl/Kconfig.vpl
This makes the whole of common/spl/Kconfig slightly more readable.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR
CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_SPL_ARGS_ADDR
In doing so, we also consistently use this variable for SPL_OS_BOOT and
not CONFIG_SYS_FDT_BASE in some cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_SPL_MALLOC_SIZE
CONFIG_SYS_SPL_MALLOC_START
We introduce a default value here as well, and CONFIG_SYS_SPL_MALLOC to
control if we have a malloc pool or not.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_RELOC_TEXT_BASE
CONFIG_SPL_RELOC_STACK
CONFIG_SPL_RELOC_MALLOC_ADDR
CONFIG_SPL_RELOC_MALLOC_SIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
Update the Kconfig entry to have the correct defaults for i.MX7
platforms, and move the existing large comment from imx7_spl.h to
doc/imx/common/imx7.txt so that it's not lost.
Signed-off-by: Tom Rini <trini@konsulko.com>
Update the Kconfig entry to have the correct defaults for i.MX6
platforms, and move the existing large comment from imx6_spl.h to
doc/imx/common/imx6.txt so that it's not lost.
Signed-off-by: Tom Rini <trini@konsulko.com>
A number of PowerPC platforms define this, for SPL. To move this to
Kconfig, it needs to be CONFIG_SPL_SYS_CCSR_DO_NOT_RELOCATE, so use
CONFIG_IS_ENABLED() to check for usage. A number of layerscape
platforms bring this logic from PowerPC, but only need a small part of
it, for the fman driver. Remove their unused portion at least.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_BSS_MAX_SIZE
CONFIG_SPL_MAX_FOOTPRINT
Note that the da850evm platforms were violating the "only use one" rule
here, and so now hard-code their BSS limit.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_PAD_TO
CONFIG_SPL_MAX_SIZE
CONFIG_TPL_PAD_TO
CONFIG_TPL_MAX_SIZE
Note that we need to make TPL_MAX_SIZE be hex, and so move and convert the
existing places.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_FS_LOAD_ARGS_NAME
CONFIG_SPL_FS_LOAD_KERNEL_NAME
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_INIT_MINIMAL
CONFIG_SPL_FLUSH_IMAGE
CONFIG_SPL_SKIP_RELOCATE
Signed-off-by: Tom Rini <trini@konsulko.com>
This is only referenced in non-SPL_DM cases, of which there are
currently none. Remove this option and slightly re-organize the code is
there is now never an if/else at the start of spl_sata_load_image()
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a new device tree property "u-boot,version" in the chosen node to
pass the U-Boot version to the operating system.
This can be useful to implement a firmware upgrade procedure from the
operating system.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
If the fitImage has some bad block in fit image area, the
offset must be recalulcated. This should be done always.
After implementing it in mxs now is possible to call the function
even for that platform.
Cc: Fabio Estevam <festevam@gmail.com>
Tested-By: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Drop CONFIG_NEEDS_MANUAL_RELOC ifdefs in board_init_r() and use
IS_ENABLED() instead. Also, use the MANUAL_RELOC() macro to update the
initcall pointers.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
There is currently no support for PRE_CONSOLE_BUFFER in SPL, but if
and when that gets implemented, one would almost certainly want to use
a different address and/or size for the buffer (e.g., U-Boot proper
might specify an address in DRAM and a generous buffer, while SPL
would be much more constrained).
So a prerequisite for adding SPL_PRE_CONSOLE_BUFFER is to make the
code use SPL_-specific values. No functional change.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Booting of non-FIT images bypass our chain-of-trust boot flow,
these options should not be allowed when high security is set.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This matches what this support is called in the non-SPL case. The postfix
_SUPPORT is redundant as enabling Kconfig options implies support.
With this we can use CONFIG_IS_ENABLED() as needed.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
UEFI:
* Fix build errors due to
- using sed with non-standard extension for regular expression
- target architecture not recognized for CROSS_COMPILE=armv7a-*
- CONFIG_EVENT not selected
* add sha384/512 on certificate revocation
Others:
* factor out the user input handling in bootmenu command
-----BEGIN PGP SIGNATURE-----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=Kdu1
-----END PGP SIGNATURE-----
Merge tag 'efi-2022-07-rc3-2' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-07-rc3-2
UEFI:
* Fix build errors due to
- using sed with non-standard extension for regular expression
- target architecture not recognized for CROSS_COMPILE=armv7a-*
- CONFIG_EVENT not selected
* add sha384/512 on certificate revocation
Others:
* factor out the user input handling in bootmenu command
This commit moves the user input handling from cmd/bootmenu.c
to common/menu.c to reuse it from other modules.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This has been deprecated for over 10 years and everything now uses the
plain "phandle" property in preference. There's no need to set
linux,phandle when creating phandles for nodes that do not have one.
dtc changed the default to creating just phandle in version 1.4.5
released in September 2017 with the justification that the new style had
already been supported for 7 years by that point (see dtc commit 0016f8c
("dtc: change default phandles to ePAPR style instead of both")).
Signed-off-by: John Keeping <john@metanate.com>
menu_get_choice() needs to handle the case that menu item
is empty. In this case, menu_get_choice() returns -ENOENT.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
To make user aware of the menu entry selection, menu always
appears regardless of the number of entry.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Adjust test/py/tests/test_bootmenu.py
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add support for VPL, a new phase of U-Boot. This runs after TPL. It is
responsible for selecting which SPL binary to run, based on a
verified-boot process.
Signed-off-by: Simon Glass <sjg@chromium.org>
This feature is not available in SPL unless common/ and lib/ are built.
Update the Kconfig to avoid build errors.
Signed-off-by: Simon Glass <sjg@chromium.org>
efi_init_early() creates an event hook for block device probing.
It has to be called before any block device is probed.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
When env support is disabled then usage of env_get() generates linker
errors. So do not compile env_get() when env support is disabled (for
example when disabled only in SPL).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
As removal of nds32 has been ack'd for the Linux kernel, remove support
here as well.
Cc: Rick Chen <rick@andestech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
To quote the author:
The bootflow feature provide a built-in way for U-Boot to automatically
boot an Operating System without custom scripting and other customisation.
This is called 'standard boot' since it provides a standard way for
U-Boot to boot a distro, without scripting.
It introduces the following concepts:
- bootdev - a device which can hold a distro
- bootmeth - a method to scan a bootdev to find bootflows (owned by
U-Boot)
- bootflow - a description of how to boot (owned by the distro)
This series provides an implementation of these, enabled to scan for
bootflows from MMC, USB and Ethernet. It supports the existing distro
boot as well as the EFI loader flow (bootefi/bootmgr). It works
similiarly to the existing script-based approach, but is native to
U-Boot.
With this we can boot on a Raspberry Pi 3 with just one command:
bootflow scan -lb
which means to scan, listing (-l) each bootflow and trying to boot each
one (-b). The final patch shows this.
With a standard way to identify boot devices, booting become easier. It
also should be possible to support U-Boot scripts, for backwards
compatibility only.
...
The design is described in these two documents:
https://drive.google.com/file/d/1ggW0KJpUOR__vBkj3l61L2dav4ZkNC12/view?usp=sharinghttps://drive.google.com/file/d/1kTrflO9vvGlKp-ZH_jlgb9TY3WYG6FF9/view?usp=sharing
Add a bootdev driver for USB host. It can use the distro boot mechanism to
locate a file, or any other available bootmeth.
Signed-off-by: Simon Glass <sjg@chromium.org>
In the next commit, CONFIG_EFI_SETUP_EARLY will become mandated
in order to support dynamic enumeration of efi_disk objects.
This can, however, be problematic particularly in case of file-based
variable storage (efi_variable.c, default).
Non-volatile variables are to be restored from EFI system partition
by efi_init_variables() in efi_init_obj_list(). When efi_init_obj_list()
is called in board_init_r(), we don't know yet what disk devices
we have since none of device probing commands (say, scsi rescan) has not
been executed at that stage.
So in this commit, a preparatory change is made; efi_init_obj_list() is
broken into the two functions;
* efi_init_early(), and
* new efi_init_obj_list()
Only efi_init_early() will be called in board_init_r(), which allows
us to execute any of device probing commands, either though "preboot"
variable or normal command line, before calling efi_init_obj_list() which
is to be invoked at the first execution of an efi-related command
(or at efi_launch_capsules()) as used to be.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
This was implemented in order to get dual-slot bootloader
partitions on the BeagleBone Black, whose MLO boots from
the first bootable partition: MLO chainloads u-boot in the
same way.
Signed-off-by: Jérôme Carretero <cJ-uboot@zougloub.eu>
Reviewed-by: Tom Rini <trini@konsulko.com>
This annotates malloc and friends so that valgrind can track the heap. To
do this, we need to follow a few rules:
* Call VALGRIND_MALLOCLIKE_BLOCK whenever we malloc something
* Call VALGRIND_FREELIKE_BLOCK whenever we free something (generally after
we have done our bookkeeping)
* Call VALGRIND_RESIZEINPLACE_BLOCK whenever we change the size of an
allocation. We don't record the original request size of a block, and
neither does valgrind. For this reason, we pretend that the old size of
the allocation was for 0 bytes. This marks the whole allocaton as
undefined, so in order to mark all bits correctly, we must make the whole
new allocation defined with VALGRIND_MAKE_MEM_DEFINED. This may cause us
to miss some invalid reads, but there is no way to detect these without
recording the original size of the allocation.
In addition to the above, dlmalloc itself tends to make a lot of accesses
which we know are safe, but which would be unsafe outside of dlmalloc. For
this reason, we provide a suppression file which ignores errors ocurring in
dlmalloc.c
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Documentation:
* Describe how enable DM_SERIAL for a board
UEFI
* Preparatory patches for better integration of DM and UEFI
* Use sysreset after capsule updates instead of do_reset
* Allow to disable persisting non-volatile variables
-----BEGIN PGP SIGNATURE-----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=SxkC
-----END PGP SIGNATURE-----
Merge tag 'efi-2022-07-rc1' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-07-rc1
Documentation:
* Describe how enable DM_SERIAL for a board
UEFI
* Preparatory patches for better integration of DM and UEFI
* Use sysreset after capsule updates instead of do_reset
* Allow to disable persisting non-volatile variables
Every time a usb bus/port is scanned and a new device is detected,
we want to call device_probe() as it will give us a chance to run
additional post-processings for some purposes.
In particular, support for creating partitions on a device will be added.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use the CONFIG macros to conditionally build the GPIO hogging support in
either the SPL or U-Boot, or both, depending on the configuration. Also
call the GPIO hog probe function in the common SPL board initialization
as an equivalent to adding it to the U-Boot init sequence functions.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This doesn't really make much sense in the documentation. Add a code
comment instead.
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
A big part is the DM pinctrl driver, which allows us to get rid of quite
some custom pinmux code and make the whole port much more robust. Many
thanks to Samuel for that nice contribution! There are some more or less
cosmetic warnings about missing clocks right now, I will send the trivial
fixes for that later.
Another big chunk is the mkimage upgrade, which adds RISC-V and TOC0
(secure images) support. Both features are unused at the moment, but I
have an always-secure board that will use that once the DT lands in the
kernel.
On top of those big things we have some smaller fixes, improving the
I2C DM support, fixing some H6/H616 early clock setup and improving the
eMMC boot partition support.
The gitlab CI completed successfully, including the build test for all
161 sunxi boards. I also boot tested on a A64, A20, H3, H6, and F1C100
board. USB, SD card, eMMC, and Ethernet all work there (where applicable).
Platforms can overwrite the weak definition of spl_mmc_boot_mode() to
determine where to load U-Boot proper from.
For most of them this is a trivial decision based on Kconfig variables,
but it might be desirable the probe the actual device to answer this
question.
Pass the pointer to the mmc struct to that function, so implementations
can make use of that.
Compile-tested for all users changed.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Ley Foon Tan <ley.foon.tan@inte.com> (for SoCFPGA)
Acked-by: Lokesh Vutla <lokeshvutla@ti.com> (for OMAP and K3)
Reviewed-by: Simon Glass <sjg@chromium.org>
When u-boot is used as a chain-loaded bootloader (replacing OS kernel),
previous bootloader leaves data in RAM, that can be reused.
For example, on recent arm linux system, when chainloading u-boot,
there are initramfs and fdt in RAM prepared for OS booting. Initramfs
may be modified to store u-boot's payload, thus providing the ability to
use chainloaded u-boot to boot OS without any storage support.
Two config options added:
- SAVE_PREV_BL_INITRAMFS_START_ADDR
saves initramfs start address to 'prevbl_initrd_start_addr' environment
variable
- SAVE_PREV_BL_FDT_ADDR
saves fdt address to 'prevbl_fdt_addr' environment variable
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
This adds a boot method for loading the next stage from the host. It is
mostly modeled off of spl_load_image_ext. I am not really sure why/how
spl_load_image_fat uses three different methods to load the image, but
the simple case seems to work OK for now.
To control the presence of this boot method, we add a config symbol.
While we're at it, we update the original semihosting config symbol.
I think semihosting has some advantages of other forms of JTAG boot.
Common other ways to boot from JTAG include:
- Implementing DDR initialization through JTAG (typically with dozens of
lines of TCL) and then loading U-Boot. The DDR initialization
typically uses hard-coded register writes, and is not easily adapted
to different boards. BOOT_DEVICE_SMH allows booting with SPL,
leveraging U-Boot's existing DDR initialization code. This is the
method used by NXP's CodeWarrior IDE on Layerscape processors (see
AN12270).
- Loading a bootloader into SDRAM, waiting for it to initialize DDR, and
then loading U-Boot. This is tricky, because the debugger must stop the
boot after the bootloader has completed its work. Trying to load
U-Boot too early can cause failure to boot. This is the method used by
Xilinx with its Zynq(MP) processors.
- Loading SPL with BOOT_DEVICE_RAM and breaking before SPL loads the
image to load U-Boot at the appropriate place. This can be a bit
tricky, because the load address is dependent on the header size. An
elf with symbols must also be used in order to stop at the appropriate
point. BOOT_DEVICE_SMH can be viewed as an extension of this process,
where SPL automatically stops and tells the host where to place the
image.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Add the support of image pre load in spl or tpl
when loading an image from ram.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
This is not defined by any board. Even sandbox doesn't actually use
it since it has migrated to DM_VIDEO.
Drop this option. Remove the dead code also, for completeness, even
though the whole lcd.c file will be dropped soon.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Drop the Kconfigs which are not used and all references to them. In
particular, this drops CONFIG_VIDEO to avoid confusion and allow us to
eventually rename CONFIG_DM_VIDEO to CONFIG_VIDEO.
Also drop the prototype for video_get_info_str() which is no-longer used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
The non-driver model video support was removed two years ago. Drop this
driver, which is only used by nokia_rx51.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is a legacy driver and the value is set in board config headers
without a CONFIG prefix. Remove the code.
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Fix the help which should refer to TPL, not SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Suggested-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Instead of a special function, send an event after driver model is inited
and adjust the boards which use this function.
Signed-off-by: Simon Glass <sjg@chromium.org>
This hook can be implmented using events, for the three boards that
actually use it.
Add the event type and event handlers. Drop CONFIG_MISC_INIT_F since we
can just use CONFIG_EVENT to control this. Since sandbox always enables
CONFIG_EVENT, we can drop the defconfig lines there too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Generate events when devices are probed or removed, allowing hooks
to be added for these situations.
This is controlled by the DM_EVENT config option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a way to create and dispatch events without needing to allocate
memory. Also add a way to 'spy' on events, thus allowing 'hooks' to be
created.
Use a linker list for static events, which we can use to replace functions
like arch_cpu_init_f(). Allow an EVENT_DEBUG option which makes it
easier to see what is going on at runtime, but uses more code space.
Dynamic events allow the creation of a spy at runtime. This is not always
necessary, but can be enabled with EVENT_DYNAMIC if needed.
A 'test' event is the only option for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
When CONFIG_SPL_FIT is enabled we do not access U-Boot directly in
the image, since it is embedded in a FIT which is parsed at runtime.
Provide a CONFIG option to drop the symbols in this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
These symbols are incorrect, meaning that binman cannot find the
associated entry. This leads to errors like:
binman: Section '/binman/simple-bin': Symbol '_binman_spl_prop_size'
in entry '/binman/simple-bin/u-boot-spl/u-boot-spl-nodtb':
Entry 'spl' not found in list (mkimage,u-boot-spl-nodtb,
u-boot-spl-bss-pad,u-boot-spl-dtb,u-boot-spl,u-boot-img,main-section)
Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Replace %zx by %lx and cast size_t to ulong.
U-Boot currently prints garbage debug output:
size=x, ptr=18, limit=18: 4002a000
With this change it prints correct debug data:
size=18, ptr=18, limit=2000: 4002a000
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Listing MTD partitions directly in the flash mode has been deprecated
for a while for kernel Device Trees. Look for a node "partitions" in the
found flash nodes and use it instead of the flash node itself for the
partition list when it exists, so Device Trees following the current
best practices can be fixed up.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Using the XHCI driver, the function `usb_kbd_poll_for_event` takes
30-40ms to run. The exact time is dependent on the polling interval the
keyboard requests in its descriptor, and likely cannot be significantly
reduced without major rework to the XHCI driver.
The U-Boot EFI console service sets a timer to poll the keyboard every 5
microseconds, and this timer is checked every time a block is read off
disk. The net effect is that, on my system, loading a ~40MiB kernel and
initrd takes about 62 seconds with a slower keyboard and 53 seconds
with a faster one, with the vast majority of the time spent polling the
keyboard.
To solve this problem, this patch adds a 20ms delay between consecutive
calls to `usb_kbd_poll_for_event`. This is sufficient to reduce the
total loading time to under half a second for both keyboards, and does
not impact the perceived keystroke latency.
Signed-off-by: Thomas Watson <twatson52@icloud.com>
Use the new IF_ENABLED_INT() feature to avoid needing our own inline
function to handle this case. Tidy up the logic to ensure that the value
is only used when present. Update the 'expected' comment also.
Signed-off-by: Simon Glass <sjg@chromium.org>
ymodem_read_fit() driver will end copying up to BUF_SIZE boundary even
when requested size of copy operation is less than that.
For example, if offset = 0, size = 1440B, ymodem_read_fit() ends up
copying 2KB from offset = 0, to destination buffer addr
This causes data corruption when malloc'd buffer is passed during UART
boot since commit 03f1f78a9b ("spl: fit: Prefer a malloc()'d buffer
for loading images")
With this, UART boot works again on K3 (AM654, J7, AM64) family of
devices.
Fixes: 03f1f78a9b ("spl: fit: Prefer a malloc()'d buffer for loading images")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Currently the names MMC1, MMC2 and MMC2_2 are output in the SPL. To
achieve more userbility here the name of the boot source can be returned.
E.g. for "MMC1" -> "eMMC" or "MMC2" -> "SD card".
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
binman support for bintools (binary tools)
minor tools improvements in preparation for FDT signing
various minor fixes and improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmHyEeYRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYYlgf8C7tQVklXz9ZHhxVrFaPHWwgmBzEZJSrc
7SWhDX9yBrAYBUk8Q4OMnJz6nXW8Rz5Td9GfBNWcJag1HjJqno4BxkqwGk2tshgj
GIY0D1cGfKJzB4E6/rK/ETwmX4KVUyEf7S2IdJ0oydkn9t7OwDkUX5WtGXo70E7q
ZJGYlX5NQCVBRAF9NYDuyVFljrPzAiyT58VCtXY3q63C7PmRYvag8r56ug+8lkk3
9EbOTcwETqq9SbT1vucyBxwbUmoKhb2BF32jEcIhozowIM3GNsSpkdzQCUnylqfa
LYI/p0oVTKLfFRBRvQjLgdB/OQP8MLkby8A++Db2OW49mBXhn/5JWA==
=PdpE
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-26jan22' of https://source.denx.de/u-boot/custodians/u-boot-dm
acpi refactoring to allow non-x86 use
binman support for bintools (binary tools)
minor tools improvements in preparation for FDT signing
various minor fixes and improvements
Add support for CDC ACM using the new UDC and gadget API. This protocol
can be used for serial over USB data transfer and is widely supported
by various OS (GNU/Linux, MS-Windows, OSX...). The usual purpose of
such link is to access device debug console and can be useful for
products not exposing regular UART to the user.
A default stdio device named 'usbacm' is created, and can be used
to redirect console to USB link over CDC ACM:
> setenv stdin usbacm; setenv stdout usbacm
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
At present we rely on the key blob being in the global_data fdt_blob
pointer. This is true in U-Boot but not with tools. For clarity, pass the
parameter around.
Signed-off-by: Simon Glass <sjg@chromium.org>
Replace CONFIG_SYS_MAX_FLASH_BANKS by CFI_FLASH_BANKS to prepare
Kconfig migration and avoid to redefine CONFIG_SYS_MAX_FLASH_BANKS
in cfi_flash.h.
After this patch CONFIG_SYS_MAX_FLASH_BANKS should be never used in
the cfi code: use CFI_MAX_FLASH_BANKS for struct size or CFI_FLASH_BANKS
for number of CFI banks which can be dynamic.
This patch modify all the files which include mtd/cfi_flash.h.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Falcon mode is very useful in improving boot speed. A question that
Falcon mode asks is "Where do I look for the kernel". With MMC boot
media, the correct answer is CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR.
The scope of this patch is to move this to Kconfig.
It is possible for a system to support Falcon mode from NOR but not
MMC. In that case, mmc_load_image_raw_os() would not be used. To
address this, conditionally compile mmc_load_image_raw_os() when
SPL_FALCON_BOOT_MMCSD, instead of SPL_OS_BOOT.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Move spl_start_uboot to its own guard in spl_mmc.c, rerun migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
- fdt_support: Add fdt_for_each_node_by_compatible() helper macro
(Marek)
- turris_omnia: Fixup SATA or PCIe nodes at runtime in DT blob (Pali)
- pci_mvebu: Add support for Kirkwood PCIe controllers (Pali)
- SPL: More verifications for kwbimage in SPL (Pali)
- mvebu: Remove comphy_update_map() (Pali)
- Minor misc stuff
Commit 9baab60b80 ("SPL: Add support for parsing board / BootROM specific
image types") added support for loading board specific image types.
This commit adds support for a new weak function spl_parse_board_header()
which is called after loading boot image. Board may implement this function
for checking if loaded board specific image is valid.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add parameter spl_boot_device to spl_parse_board_header(), which allows
the implementations to see from which device we are booting and do
boot-device-specific checks of the image header.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add macro fdt_for_each_node_by_compatible() to allow iterating over
fdt nodes by compatible string.
Convert various usages of
off = fdt_node_offset_by_compatible(fdt, start, compat);
while (off > 0) {
code();
off = fdt_node_offset_by_compatible(fdt, off, compat);
}
and similar, to
fdt_for_each_node_by_compatible(off, fdt, start, compat)
code();
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Drop the remaining ifdefs around header includes, to fix an old TODO.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Not all architectures define <asm/gpio.h> and even on those that do, the
header cannot be included for all boards without causing various build
failures.
Since common/board_r.c only needs gpio_hog_probe_all() declaration, include
<asm-generic/gpio.h> and drop the associated ifdef.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
asm/mmu.h include is currently guarded by CONFIG_ADDR_MAP ifdef because
the header is only present on arm and powerpc. In order to remove the
dependency on this header and the associated ifdef, move init_addr_map()
declaration to init.h, since it is only called during the common init
sequence.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Add a return value to init_addr_map and use it directly in the
post-relocation init sequence, rather than using a wrapper stub.
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Add a return value to kgdb_init and use it directly in the post-relocation
init sequence, rather than using a wrapper stub. Also, move the "KGDB"
print message inside kgdb_init().
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Commit 98f705c9ce ("powerpc: remove 4xx support") removed (in 2017) the
last code that made use of bedbug debugger support. Since there aren't
any boards left that define either CONFIG_CMD_BEDBUG or a real
bedbug_init(), drop this feature from u-boot.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Factor out armv7m fragment to spl_perform_fixups(), which is an arch/board
specific function designed for this purpose.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
This implementation is intended to be copied to other projects and
modified, to as to foster a standard means of communcating runtime
information between firmware projects.
The GPL-2 license is too restrictive for some projects, e.g. those
intended as reference implementations rather than designed for
collaborative open-source development.
Update the license to make this easier to share.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we do support allocating the bloblist but the Kconfig is a bit
strange, since we still have to specify an address in that case. Partly
this is because it is a pain to have CONFIG options that disappears when
its dependency is enabled. It means that we must have #ifdefs in the code,
either in the C code or header file.
Make use of IF_ENABLED_INT() and its friend to solve that problem, so we
can separate out the location of bloblist into a choice. Put the address
and size into variables so we can log the result.
Add the options for SPL as well, so we can use CONFIG_IS_ENABLED().
Signed-off-by: Simon Glass <sjg@chromium.org>
We typically refer to the different U-Boot builds that a board runs
through as phases. This avoids confusion with the word 'stage' which is
used with bootstage, for example. Fix up some bloblist Kconfig help
which uses the wrong term.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present if someone adds a tag in the middle of the list it works well
enough within a U-Boot build. But if these tags are used in another
project, or with an older version of SPL, the numbers make become
inconsistent.
Use explicit tag numbers that never change, to resolve this problem.
Allocate areas for existing U-Boot tags and set up an area for use by
projects and vendors, as well as for private use. Keep tags above
0x10000 unallocated for now.
Update bloblist_tag_name() and the tests to work with this new setup.
Signed-off-by: Simon Glass <sjg@chromium.org>
The EC event log tag is no-longer used. The vboot handoff is now handled
by the vboot context instead.
Drop these unused tags.
Signed-off-by: Simon Glass <sjg@chromium.org>
Documentation:
* Add Sunxi board description
UEFI:
* Improvements to U-Boot running on top of UEFI
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEbcT5xx8ppvoGt20zxIHbvCwFGsQFAmHOp5gACgkQxIHbvCwF
GsTonA//Y8wwlaXA1TD6B0fIEcQiZucDJQD0nbHugx+1xw/7w9wHX1qfM4Tskqc4
y4RA3QyoyUp7tvesP6/EA3mAUSEUp0nrtLPyCJjjXV1lrOaXhwvbdqrhOCqUQLen
h6RNjhujVtbC90wBWYPal3Ip0hdIUROe3qp9Mk2p4zAru8jBEShn+PTRIeHvf6UV
9BZ8j9LCivC7hUAG3Cyv+KFhW1s47IN54WddedIREEWk4vIdrUMRLjW/kW8ZbDxx
gi1Eec25Rte6+p5k/+TJkvCwA8GC1kW+MFMYWxcAARZlUd0yr/S6ru5yaW8km0KQ
kKgcYGp878hVB41JFEhiGUf9CkwU2oo+3NZGIfNv/vG45J4UppyqNffm9c3ZudWC
S6DqRVPSp1YQEs45SIVZGx+LK6s1iTBn3DJ/dX68NavuUIYX2nnveUBgtW5vdzGf
ba0yh4a0EU36hcjd2o3y3sEAjiy+PF8SAZ+f2HQ7JaLjsCWF1zNFGsiAxaEStHp8
aVrUN0cWQPKnnI2A8DCqjmMaSBDKZDK59k6EeC1ZFdMmGivHEO61A0sDiUTz+IRW
U7XLvjAA5IVKAtij6T/iab6qvhgwABJRL9lZI5DMiFxJRSl4uSYe9YviG7+EzUg0
XMIs5nK6jBB74HPKqhBouiSUiRa9UHY/rdyNhJACHQ8GODzCf04=
=YdSB
-----END PGP SIGNATURE-----
Merge tag 'efi-next' of https://source.denx.de/u-boot/custodians/u-boot-efi into next
Pull request of efi-next
Documentation:
* Add Sunxi board description
UEFI:
* Improvements to U-Boot running on top of UEFI
Since EFI does not relocate and uses the same global_data pointer
throughout the board-init process, drop this unnecessary setup, to avoid
a hang.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
- support for showing a logo without splash screen config
- support for BMP drawing to depths other than 16bpp
- tests for the different types of supported BMP images
- support showing a logo when running coreboot via qemu
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCYcsdCQ4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXCLhAJ9pLJE3SpQRzpm+Nu4EMbCDzZKr+wCfbxnAZ9LC
zS1XZ6u9Se4ysDb+PYs=
=Hf5j
-----END PGP SIGNATURE-----
Merge tag 'video-next-20211228' of https://source.denx.de/u-boot/custodians/u-boot-video into next
- various fixes to the sandbox display support
- support for showing a logo without splash screen config
- support for BMP drawing to depths other than 16bpp
- tests for the different types of supported BMP images
- support showing a logo when running coreboot via qemu
This converts the following to Kconfig:
CONFIG_SYS_FSL_CLK
We move the exiting option to common/Kconfig near the other options to
control the contents of board_init_f() and note that this is a legacy
option. We further restrict this to where the call is going to be
non-empty, for the SoCs that had only been using this for some
MMC-related clocks.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_VIDEO_LOGO
Note that this option depends on CONFIG_DM_VIDEO now, since cfb_console is
deprecated. The only relevant code is now in splash.c
Drop the check for DM_VIDEO in that file.
Signed-off-by: Simon Glass <sjg@chromium.org>
The video driver uses this for debugging, but if used before relocation it
crashes at present. Avoid trying to output debugging before the console is
ready.
Signed-off-by: Simon Glass <sjg@chromium.org>
When running, if the devicetree failed to come from the expected source,
show a warning, e.g:
U-Boot ...
DRAM: 128 MiB
Core: 42 devices, 11 uclasses, devicetree: separate
Warning: Unexpected devicetree source (not from a prior stage)
Warning: U-Boot may not function properly
Flash: 64 MiB
...
These warnings should only appear if the board config has been changed, or
the prior stage is broken.
Signed-off-by: Simon Glass <sjg@chromium.org>
It can be confusing to figure out where the devicetree came from. It seems
important enough to warrant a message during boot. Add information about
the number of devices and uclasses too since it is helpful to have some
idea what is going on with driver model.
Report the devicetree source in bdinfo too.
This looks something like this, with > marking the new line.
U-Boot 2021.10-00190 (Oct 30 2021 - 09:01:29 -0600)
DRAM: 128 MiB
> Core: 42 devices, 11 uclasses, devicetree: passage
Flash: 64 MiB
Signed-off-by: Simon Glass <sjg@chromium.org>
Move Turris MOX specific remove_disabled_nodes() to fdt_support with
name fdt_delete_disabled_nodes(), so that others can potentially use it.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add functions
fdt_node_offset_by_pathf(),
fdt_create_phandle_by_pathf(),
fdt_set_status_by_pathf()
to get node offset, get/create node phandle and set status for node
given by path/alias formatted with sprintf.
Add functions
fdt_create_phandle_by_compatible(),
fdt_set_status_by_compatible()
to get/create node phandle and set status for first node given by
compatible.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
This function does not necessarily create a new phandle. If a phandle
exists, no new phandle is created.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Since no one uses this feature and I am not aware of any parsers of this
in Linux, remove it.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit f0921f5098 ("fdt: Sync up to the latest libfdt") introduced
fdt_generate_phandle() in libfdt, making fdt_alloc_phandle() obsolete in
fdt_support.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: "hui.song" <hui.song_1@nxp.com>
Cc: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Typically the bloblist is positioned at a fixed address in memory until
relocation. This is convenient when it is set up in SPL or before
relocation.
But for EFI we want to set it up only when U-Boot proper is running. Add
a way to allocate it using malloc() and update the documentation to cover
this aspect of bloblist.
Note there are no tests of this feature at present, nor any direct testing
of bloblist_init().
This can be added, e.g. by making this option controllable at runtime.
Signed-off-by: Simon Glass <sjg@chromium.org>
When, for various reasons, a bad FIT image is used where a loadable
image is marked as 0 length, attempt is made for a 0 length allocation and
read of 0 byte read operation.
Instead provide warning in log and skip attempting to do such a load.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Add a new function to activate an existing simple frame buffer node
and add the associated reserved memory, with no-map properties.
This device tree update is only done when the video device is active
and the video buffer is used.
This patch uses '#if CONFIG_IS_ENABLED(DM_VIDEO)' because
gd->video_bottom and gd->video_top are only defined when CONFIG_DM_VIDEO
is activated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Rename the function named lcd_dt_simplefb* to fdt_simplefb* to be aligned
with the associated file name fdt_simplefb.h/fdt_simplefb.c
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Rename the file lcd_simplefb.c to fdt_simplefb.c to be aligned
with the configuration name and with the associated include file
./include/fdt_simplefb.h
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This converts the following to Kconfig:
CONFIG_LCD_DT_SIMPLEFB
This patch also renames this config to CONFIG_FDT_SIMPLEFB as the code in
common/lcd_simplefb.c support CONFIG_LCD and CONFIG_VIDEO.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Before relocation there is generally not as much available memory and not
that much console output. At present the console-output buffer is the same
side before and after relocation. Add a separate Kconfig option to remove
this limitation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Even if U-Boot has relocation disabled via GD_FLG_SKIP_RELOC , the
relocated stage of U-Boot still picks GD from new_gd location. The
U-Boot itself is not relocated, but GD might be, so copy the GD to
new GD location even if relocation is disabled.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Peng Fan <peng.fan@oss.nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
The last board that used to set CONFIG_LYNXKDI has been removed in
commit 242836a893 ("powerpc: ppc4xx: remove pcs440ep support"),
doc/README.lynxkdi only talks about a MPC8260 board being supported,
and the mpc8260 support has been removed four years ago in commit
2eb48ff7a2 ("powerpc, 8260: remove support for mpc8260") already,
and common/lynxkdi.c only consists of an "#error" statement these
days, so it seems like the LYNX KDI code is dead code nowadays.
Let's remove it now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Quite a lot of the code in common/relates to booting and images. Before
adding more it seems like a good time to move the code into its own
directory.
Most files with 'boot' or 'image' in them are moved, except:
- autoboot.c which relates to U-Boot automatically running a script
- bootstage.c which relates to U-Boot timing
Drop the removal of boot* files from the output directory, since this
interfers with the symlinks created by tools and there does not appear
to be any such file from my brief testing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Artem Lapkin <email2tema@gmail.com>
Tested-by: Artem Lapkin <email2tema@gmail.com>
This statement has an unmatched parentheses, fix it.
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When building a system that has both TPL and SPL_OS_BOOT, code which
tests for CONFIG_SPL_OS_BOOT will be built and enabled in TPL, which is
not correct. While there is no CONFIG_TPL_OS_BOOT symbol at this time
(and likely will not ever be) we can use CONFIG_IS_ENABLED(OS_BOOT) in
these common paths to ensure we only compile these parts in the SPL
case.
Signed-off-by: Tom Rini <trini@konsulko.com>
Allow usage of the bootstage facilities in SPL.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The data blob apparently does not need to be modified through the fit
field of the image_sign_info struct so make it point to const to avoid
the need to cast away constness in functions that assign a pointer to
const data to the field.
fit_image_setup_verify already had to cast away constness as it assigned
a const void * argument to the field. The cast can now be removed.
Signed-off-by: Hannu Lounento <hannu.lounento@vaisala.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The padding pss is only supported on u-boot and tools since
commit 2bbed3ff8c ("image: Use Kconfig to enable FIT_RSASSA_PSS on host")
This commit adds the config SPL_FIT_RSASSA_PSS to support
the padding pss in the SPL.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make sure to (if applicable) flush the D-cache, invalidate I-cache,
and disable MMU and caches before jumping to OPTEE.
This fixes the SDP->SPL->OPTEE boot flow on iMX6Q and most likely on
some other ARM SoCs.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
After DM_VIDEO conversion the 'vidconsole' is the correct name
for the frame buffer console. 'video' will not work, so update
the description of the config option.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
At present U-Boot has a header file called lz4.h for its own use. If the
host has its own lz4 header file installed (e.g. from the 'liblz4-dev'
package) then host builds will use that instead.
Move the U-Boot file into its own directory, as is done with various
other headers with the same problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is far too long. Before trying to remove #ifdefs, split out
the code that deals with selecting the FDT into a separate function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use boolean variables to deal with the strange #ifdef logic of this
function, so we can remove the #ifdefs.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is far too long. Before trying to remove #ifdefs, split out
the code that deals with selecting the ramdisk into a separate function.
Leave the code indented as it was for easier review. The next patch cleans
this up along with checkpatch violations.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is only used in one place and does not need to use the
preprocessor. Move it to the C file and convert it to a normal function.
Drop fit_unsupported() since it is not used.
Signed-off-by: Simon Glass <sjg@chromium.org>
We can use the new host_build() function for this, so drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This is not needed with Kconfig, since we can use IS_ENABLED() easily
enough. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This is not needed with Kconfig, since we can use IS_ENABLED() easily
enough. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This is not needed with Kconfig, since we can use IS_ENABLED() easily
enough and the board code is now in a separate file. Update the only place
where this is used and drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Add a host Kconfig for CRC32. With this we can use CONFIG_IS_ENABLED(CRC32)
directly in the host build, so drop the unnecessary indirection.
Add a few more conditions to SPL_CRC32 to avoid build failures as well as
TPL_CRC32. Also update hash.c to make crc32 optional and to actually take
notice of SPL_CRC32.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Add a host Kconfig for OF_LIBFDT. With this we can use
CONFIG_IS_ENABLED(OF_LIBFDT) directly in the tools build, so drop the
unnecessary indirection.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Make use of the host Kconfig for FIT. With this we can use
CONFIG_IS_ENABLED(FIT) directly in the host build, so drop the unnecessary
indirection.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
We can use the __maybe_unused attribute to avoid some of the #ifdefs in
this file. Update the functions accordingly.
Note: The actual hashing interface is still a mess, with four separate
combinations and lots of #ifdefs. This should really use a driver
approach, e.g. as is done with partition drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
At present when building host tools, we force CONFIG_SHAxxx to be enabled
regardless of the board Kconfig setting. This is done in the image.h
header file.
For SPL we currently just assume the algorithm is desired if U-Boot proper
enables it.
Clean this up by adding new Kconfig options to enable hashing on the host,
relying on CONFIG_IS_ENABLED() to deal with the different builds.
Add new SPL Kconfigs for hardware-accelerated hashing, to maintain the
current settings.
This allows us to drop the image.h code and the I_WANT_MD5 hack.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
In preparation for enabling CONFIG_IS_ENABLED() on the host build, add
some options to enable the various FIT options expected in these tools.
This will ensure that the code builds correctly when CONFIG_TOOLS_xxx
is distinct from CONFIG_xxx.
Drop some #ifdefs which are immediately unnecessary (many more are in
later patches).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
With the new TOOLS_LIBCRYPTO and some other changes, it seems that we are
heading towards calling this a tools build rather than a host build,
although of course it does happen on the host.
I cannot think of anything built by the host which cannot be described as
a tool, so rename this function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Add a macro to handle manually relocating a pointer. Update the iamge code
to use this to avoid needing #ifdefs.
This also fixes a bug where the 'done' flag was not set.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than adding an #ifdef and open-coding this calculation, add a
helper function to handle it. Use this in the image code.
Signed-off-by: Simon Glass <sjg@chromium.org>
To avoid having #ifdefs in a few functions which are completely different
in the board and host code, create a new image-host.c file.
Signed-off-by: Simon Glass <sjg@chromium.org>
To avoid a large #ifdef in the image.c file, move the affected code into
a separate file.
Avoid any style fix-ups for easier review. Those are in the next patch.
Signed-off-by: Simon Glass <sjg@chromium.org>
Adjust this function so that preprocessor macros are not needed. With
this, the host build uses more of the same header files as the target
build.
Rather than definining CONFIG_SYS_MALLOC_LEN, add a CONSERVE_MEMORY
define, since that is the purpose of the value.
This appears to have no impact on code size from a spot check of a few
boards (snow, firefly-rk3288, boston32r2el, m53menlo).
Signed-off-by: Simon Glass <sjg@chromium.org>
The zstd implementation prints the error in image_decomp() which is
incorrect and does not match other algorithms. Drop this and let the
caller report the error.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this function is full of preprocessor macros. Adjust it to
check for an unsupported algorithm after the switch(). This will allow
us to drop the macros.
Fix up the return-value path and an extra blank line while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
The existing zstd API requires the same sequence of calls to perform its
task. Create a helper for U-Boot, to avoid code duplication, as is done
with other compression algorithms. Make use of of this from the image
code.
Note that the zstd code lacks a test in test/compression.c and this should
be added by the maintainer.
Signed-off-by: Simon Glass <sjg@chromium.org>
cherry-picked from NXP code:
719d665a87c6: ("MLK-20467 imx8m: Fix issue for booting signed image through uuu")
which fixes secure boot on imx8m based boards. Problem was
that FIT header and so IVT header too, was loaded to
memallocated address. So the ivt header address coded
in IVT itself does not fit with the real position.
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Tim Harvey <tharvey@gateworks.com>
add hook function spl_load_simple_fit_fix_load()
which is called after fit image header is loaded.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
bootm_low is used as a base address is used to allocate space for the
FDT blob, initrd, cmdline, etc. when booting Linux. Set the default
value for RISC-V to the start of the first DRAM bank, so platforms can
get their DRAM layout from the device tree, and do not need to define
CONFIG_SYS_SDRAM_BASE.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The configuration CONFIG_OPTEE is defined 2 times:
1- in lib/optee/Kconfig for support of OPTEE images loaded by bootm command
2- in drivers/tee/optee/Kconfig for support of OP-TEE driver.
It is abnormal to have the same CONFIG define for 2 purpose;
and it is difficult to managed correctly their dependencies.
Moreover CONFIG_SPL_OPTEE is defined in common/spl/Kconfig
to manage OPTEE image load in SPL.
This definition causes an issue with the macro CONFIG_IS_ENABLED(OPTEE)
to test the availability of the OP-TEE driver.
This patch cleans the configuration dependency with:
- CONFIG_OPTEE_IMAGE (renamed) => support of OP-TEE image in U-Boot
- CONFIG_SPL_OPTEE_IMAGE (renamed) => support of OP-TEE image in SPL
- CONFIG_OPTEE (same) => support of OP-TEE driver in U-Boot
- CONFIG_OPTEE_LIB (new) => support of OP-TEE library
After this patch, the macro have the correct behavior:
- CONFIG_IS_ENABLED(OPTEE_IMAGE) => Load of OP-TEE image is supported
- CONFIG_IS_ENABLED(OPTEE) => OP-TEE driver is supported
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
We have individual SOC symbols for each keystone 2 platform. Use the
existing CONFIG_ARCH_KEYSTONE rather than CONFIG_SOC_KEYSTONE to
encompass all of the keystone families.
Signed-off-by: Tom Rini <trini@konsulko.com>
The current API is outdated as it requires a devicetree pointer.
Move these functions to use the ofnode API and update this globally. Add
some tests while we are here.
Correct the call in exynos_dsim_config_parse_dt() which is obviously
wrong.
Signed-off-by: Simon Glass <sjg@chromium.org>
Header file version.h does not use anything from timestamp.h. Including of
timestamp.h has side effect which cause recompiling object file at every
make run because timestamp.h changes at every run.
So remove timestamp.h from version.h and include timestamp.h in files
which needs it.
This change reduce recompilation time of final U-Boot binary when U-Boot
source files were not changed as less source files needs to be recompiled.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add in lib/acpi/acpi_table.c and test/dm/acpi.c, rework a few others]
Signed-off-by: Tom Rini <trini@konsulko.com>
More C files do not use compile time timestamp macros and do not have to be
recompiled every time when SOURCE_DATE_EPOCH changes.
This patch moves version_string[] from version.h to version_string.h and
updates other C files which only needs version_string[] string to include
version_string.h instead of version.h. After applying this patch these
files are not recompiled every time when SOURCE_DATE_EPOCH changes.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The hash algorithm selection was streamlined in commit 92055e138f
("image: Drop if/elseif hash selection in calculate_hash()"). Said
commit kept the call to cpu_to_uimage() to convert the CRC to big
endian format.
This would have been correct when calling crc32_wd(). However, the
->hash_func_ws member of crc32 points to crc32_wd_buf(), which already
converts the CRC to big endian. On a little endian host, doing both
conversions results in a little-endian CRC. This is incorrect.
To remedy this, simply drop the call to cpu_to_uimage(), thus only
doing the byte-order conversion once.
Fixes: 92055e138f ("image: Drop if/elseif hash selection in
calculate_hash()")
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
We are not guaranteed to have the padding_pkcs_15_verify symbol since
commit 92c960bc1d ("lib: rsa: Remove #ifdefs from rsa.h"), and
commit 61416fe9df ("Kconfig: FIT_SIGNATURE should not select RSA_VERIFY")
The padding_algos only make sense with RSA verification, which can now
be disabled in lieu of ECDSA. In fact this will lead to build failures
because of the missing symbol mentioned earlier.
To resolve this, move the padding_algos to a linker list, with
declarations moved to rsa_verify.c. This is consistent with commit
6909edb4ce ("image: rsa: Move verification algorithm to a linker list")
One could argue that the added #ifdef USE_HOSTCC is ugly, and should
be hidden within the U_BOOT_PADDING_ALGO() macro. However, this would
be inconsistent with the "cryptos" list. This logic for was not
previously explored:
Without knowledge of the U_BOOT_PADDING_ALGO() macro, its use is
similar to something being declared. However, should #ifndef
USE_HOSTCC be part of the macro, it would not be obvious that it
behaves differently on host code and target code. Having the #ifndef
outside the macro makes this obvious.
Also, the #ifdef is not always necessary. For example ecda-verify
makes use of U_BOOT_CRYPTO_ALGO() without any accompanying #ifdefs.
The fundamental issue is a lack of separation of host and target code
in rsa_verify. Therefore, the declaration of a padding algo with the
external #ifdef is more readable and consistent.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
calculate_hash() would try to select the appropriate hashing function
by a if/elseif contruct. But that is exactly why hash_lookup_algo()
exists, so use it instead.
This does mean that we now have to 'select HASH' to make sure we get
the hash_lookup_algo() symbol. However, the change makes sense because
even basic FITs will have to deal with "hash" nodes.
My only concern is that the 'select SPL_HASH' might cause some
platform to grow above its SPL size allowance
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[trini: Make FSL_CAAM be implied only on ARM && SPL]
Signed-off-by: Tom Rini <trini@konsulko.com>
MD5 is being called directly in some places, but it is not available
via hash_lookup_algo("md5"). This is inconsistent with other hasing
routines. To resolve this, add an "md5" entry to hash_algos[].
The #ifdef clause looks funnier than those for other entries. This is
because both MD5 and SPL_MD5 configs exist, whereas the other hashes
do not have "SPL_" entries. The long term plan is to get rid of the
ifdefs, so those should not be expected to survive much longer.
The md5 entry does not have .hash_init/update/finish members. That's
okay because hash_progressive_lookup_algo() will catch that, and
return -EPROTONOSUPPORT, while hash_lookup_algo() will return the
correct pointer.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[trini: Use CONFIG_IS_ENABLED not IS_ENABLED for MD5 check]
Signed-off-by: Tom Rini <trini@konsulko.com>
All of these configs exist. Stick to using CONFIG_[ST]PL_HASH, and drop all
references to CONFIG_[ST]PL_HASH_SUPPORT. This means we need for
CHAIN_OF_TRUST to select SPL_HASH now.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[trini: Add TPL case, fix CHAIN_OF_TRUST, other tweaks]
Signed-off-by: Tom Rini <trini@konsulko.com>
Originally CONFIG_FIT_SHAxxx enabled specific SHA algos for and only
for hash_calculate() in common/image-fit.c. However, since commit
14f061dcb1 ("image: Drop IMAGE_ENABLE_SHAxxx"),
the correct selector was changed to CONFIG_SHAxxx.
The extra "_FIT_" variants are neither used, nor needed. Remove them.
One defconfig disables FIT_SHA256, which is now changed to 'SHA256'.
CMD_MVEBU_BUBT needs to select select SHA256 to avoid undefined
references to "sha256_*()". bubt.c needs sha256, so this selection is
correct. It is not clear why this problem did not manifest before.
Note that SHA selection in SPL is broken for this exact reason. There
is no corresponding SPL_SHAxxx. Fixing this is is beyond the scope of
this change.
Also note that we make CONFIG_FIT now imply SHA256, to make up for
FIT_SHA256 previously being a default y option.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[trini: Add imply SHA256 to FIT]
Signed-off-by: Tom Rini <trini@konsulko.com>
The enable_caches is a generic hook for architecture-implemented, we
leverage this function to enable caches for RISC-V
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The code under drivers/net is related to ethernet networking drivers, in
some fashion or another. Drop these from the top-level Makefile and
also move the phy rule into drivers/net/Makefile which is where it
belongs. Make the new rule for drivers/net check for the build-stage
relevant ETH symbol.
Fix up some Kconfig dependencies while we're here to mirror how the
Makefile logic now works.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Introduce ETH, Kconfig dependency changes, am43xx fix]
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the power/ rules into drivers/power to avoid clutter in the Makefile
and drivers/Makefile files.
We must select SPL_POWER if SPL_POWER_DOMAIN is used, since the two are
currently independent and boards do not necessarily enable SPL_POWER.
Add a TPL_POWER as well, as that is used by one board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Rename this option so that CONFIG_IS_ENABLED can be used with it.
Oddly there is already an SPL_CACHE option. Drop it in favour of this one.
Drop the special SPL Makefile rule which is now superfluous.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Fixup some incorrect renames]
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently it is possible to cancel loadx and loady commands by pressing
CTRL+X (CAN character) at least 3 times quickly.
All other U-Boot commands, including loadb and loads can be cancelled by
CTRL+C. So allow it also in xyz-modem code used by loadx and loady
commands. Implement it by handling CTRL+C (ETX character) in the same way
as CTRL+X (CAN character).
Due to how x/y-modem protocol works, it is required to press
CTRL+C or CTRL+X at least 3 times quickly.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>