Commit Graph

71 Commits

Author SHA1 Message Date
Tom Rini
052170c6a0 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-01-22 13:38:00 -05:00
Baruch Siach
cdb494962d ARM: mvebu: clearfog: add support for EEPROM TLV info
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
2020-01-21 15:56:15 +01:00
Baruch Siach
14f14911f4 arm: mvebu: clearfog: set uboot image SD card offset
Armada 38x ROM skips the first SD card offset when loading SPL. This
affects the location of the main U-Boot image. SPL MMC code now supports
U-Boot image offset based on run-time detection of the boot partition.
Use this feature to make the same generated image support both SD card
and eMMC boot partition.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2020-01-16 10:59:07 +01:00
Baruch Siach
c853fa721d configs: clearfog: enable SPL_DM_GPIO to fix boot from SD
SPL needs DM GPIO to read the SD card-detect signal. This complements
the fix in commit 70bae02f71 ("arm: mvebu: clearfog: fix boot from SD
card").

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2020-01-16 10:58:46 +01:00
Tom Rini
0cfccb5401 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-04 17:18:38 -05:00
Miquel Raynal
63ea317245 mtd: ensure MTD is compiled when there is a SPI NOR flash using MTD
MTD must be enabled when there is a SPI NOR flash using the
SPI_FLASH_MTD config entry.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-12-04 13:26:17 -05:00
Tom Rini
a09fea1d28 env: Finish migration of common ENV options
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00
Tom Rini
0be2ecd486 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-07 17:58:06 -05:00
Tom Rini
665c35a764 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-09-23 11:47:37 -04:00
Adam Ford
1bf330150c Convert CONFIG_ARCH_CPU_INIT to Kconfig
This converts the following to Kconfig:
   CONFIG_ARCH_CPU_INIT

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Felix Brack <fb@ltec.ch>
2019-08-25 19:32:55 -04:00
Simon Glass
37304aaf60 Convert CONFIG_USE_PREBOOT and CONFIG_PREBOOT to Kconfig
This converts the following to Kconfig:
   CONFIG_USE_PREBOOT
   CONFIG_PREBOOT

Both are together in one commit, since otherwise the former causes kconfig
to define the latter, which gives duplicate symbol errors.

Includes a manual fixup for CONFIG_PREBOOT in ids8313_defconfig since the
backslash lands in the wrong place. Similarly with socfpga_vining_fpga.

Signed-off-by: Simon Glass <sjg@chromium.org>
2019-08-02 11:19:14 -04:00
Tom Rini
344a0e4367 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-05-26 14:45:25 -04:00
Stefan Roese
170aca2030 arm: mvebu: clearfog: Enable BLK and DM support
This patch enables CONFIG_BLK and some DM enabled drivers on clearfog
to remove these compile warnings:

===================== WARNING ======================
This board does not use CONFIG_DM_MMC. Please update
the board to use CONFIG_DM_MMC before the v2019.04 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ======================
This board does use CONFIG_LIBATA but has CONFIG_AHCI not
enabled. Please update the storage controller driver to use
CONFIG_AHCI before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================

Signed-off-by: Stefan Roese <sr@denx.de>
2019-05-09 07:34:38 +02:00
Alex Kiernan
623de3f086 Convert CONFIG_SUPPORT_EMMC_BOOT to Kconfig
This converts the following to Kconfig:
   CONFIG_SUPPORT_EMMC_BOOT

As requested by Michal Simek <michal.simek@xilinx.com>, these boards
have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated:

  xilinx_zynqmp_zc1275_revB
  xilinx_zynqmp_zc1751_xm018_dc4
  xilinx_zynqmp_zc1751_xm019_dc5
  xilinx_zynqmp_zcu100_revC
  xilinx_zynqmp_zcu102_rev1_0
  xilinx_zynqmp_zcu102_revA
  xilinx_zynqmp_zcu102_revB
  xilinx_zynqmp_zcu104_revA
  xilinx_zynqmp_zcu104_revC
  xilinx_zynqmp_zcu106_revA
  xilinx_zynqmp_zcu111_revA

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2019-05-04 13:04:12 -04:00
Simon Goldschmidt
f89d6133ee configs: move CONFIG_SPL_TEXT_BASE to Kconfig
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-29 21:41:40 -04:00
Tom Rini
d168bcb6fe configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-29 21:41:40 -04:00
Patrick Delaunay
14453fbfad Convert CONFIG_SF_DEFAULT_* to Kconfig
This converts the following to Kconfig:
  CONFIG_SF_DEFAULT_BUS
  CONFIG_SF_DEFAULT_CS
  CONFIG_SF_DEFAULT_MODE
  CONFIG_SF_DEFAULT_SPEED

I use moveconfig script and then manual check on generated u-boot.cfg
to solve the remaining issue.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-03-25 17:36:53 -04:00
Tom Rini
50e24381c0 Merge branch 'master' of git://git.denx.de/u-boot-spi
- SPI-NOR support
2019-02-07 14:48:56 -05:00
Vignesh R
6d82517836 configs: Don't use SPI_FLASH_BAR as default
Now that new SPI NOR layer uses stateless 4 byte opcodes by default,
don't enable SPI_FLASH_BAR. For SPI controllers that cannot support
4-byte addressing, (stm32_qspi.c, fsl_qspi.c, mtk_qspi.c, ich.c,
renesas_rpc_spi.c) add an imply clause to enable SPI_FLASH_BAR so as to
not break functionality.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07 15:33:22 +05:30
Stefan Roese
94f453ea38 pci: pci_mvebu: Add DM_PCI support and move CONFIG_PCI_MVEBU to defconfig
This patch adds DM_PCI support to the MVEBU PCIe driver. This is
necessary, since all PCI drivers have to be moved to DM (driver model)
until the v2019.07 release.

To not break git bisect'ablility, this patch also moves CONFIG_PCI_MVEBU
from config headers to the defconfig files.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: VlaoMao <vlaomao@gmail.com>
2019-02-05 14:22:38 +01:00
Tom Rini
1bac199e8c configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-01-07 18:11:00 -05:00
Tom Rini
f1cd696160 configs: Enable THUMB2 on various ARM boards
The clearfog, corvus, wb45n and picosam9g45 configs are close to
exceeding their size limits, so enable THUMB2 builds on them to reclaim
space.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-11-16 13:34:33 -05:00
Tom Rini
8c5cad05c9 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-09-03 15:26:12 -04:00
Adam Ford
d7869b2183 Convert CONFIG_MII et al to Kconfig
This converts the following to Kconfig:
   CONFIG_MII
   CONFIG_DRIVER_TI_EMAC

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-08-17 13:03:54 -04:00
Tom Rini
86cf1c8285 configs: Migrate CONFIG_NR_DRAM_BANKS
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
  CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
  2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-16 16:45:02 -04:00
Baruch Siach
ca1a4c8632 mvebu: select boot device at SoC level
Move the gdsys Controlcenter DC specific build time kwbimage.cfg
generation code into the mach-mvebu/ directory to be shared by all 32bit
mvebu platforms.

Remove board specific kwbimage.cfg files, and use the generated one
instead. These files are all identical, with two exceptions. Clearfog
and Helios4 use the sdio boot device, whereas all others use spi. Update
the defconfigs for the exceptional boards to generate the same
kwbimage.cfg as before.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-08-06 14:07:23 +02:00
Jon Nettleton
4ea813d333 arm: mvebu: switch clearfog to use device-tree i2c and gpio
This switches the clearfog boards to use DM based gpio and i2c
drivers.  The io expanders are configured via their device-tree
entries.

Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: add DT i2c aliases]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-06-05 07:29:09 +02:00
Jon Nettleton
d6db446f70 arm: mvebu: enable sata support for clearfog
The a38x sata interfaces run in ahci mode and can
be accessed via the scsi command.

Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: rebase on current upstream]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-06-05 07:29:08 +02:00
Tom Rini
358b6a20e4 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-06-04 11:57:37 -04:00
Mario Six
a8ca5c8adb treewide: Move CONFIG_PHY_MARVELL to Kconfig
The CONFIG_PHY_MARVELL has already been migrated to Kconfig (some boards
already had it in their Kconfig), but had not been moved for older
boards.

Move it to the defconfigs for all boards.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-05-14 21:28:38 -04:00
Mario Six
78eba69d98 treewide: Migrate CONFIG_DISPLAY_BOARDINFO_LATE to Kconfig
Migrate the CONFIG_DISPLAY_BOARDINFO_LATE option to Kconfig.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-08 15:12:09 -04:00
Tom Rini
c9542eae0b configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-07 20:37:13 -04:00
Baruch Siach
bc8cb152d8 configs: clearfog: enable random random MAC address
This makes the network devices usable when booting a blank board over
UART, with no pre-configured MAC address stored in the environment area.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-03-30 12:52:48 +02:00
Tuomas Tynkkynen
4a942f49b8 spi: Migrate CONFIG_KIRKWOOD_SPI to Kconfig
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-02-13 23:01:44 -05:00
Tom Rini
278b90ce78 configs: Migrate CONFIG_SYS_TEXT_BASE
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set.  This is a strict migration of the current
values into the defconfig and removing them from the headers.

I did not attempt to add more default values in and for now will leave
that to maintainers.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-11 09:30:09 -05:00
Tom Rini
7af2e3648f configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-12-18 20:19:09 -05:00
Jon Nettleton
962b8fef91 arm: mvebu: clearfog: Fix SPI-NOR flash access
The production variant of the SPI flash used by the clearfog
devices are based on winbond chips.  Additionally enable
SPI_FLASH_BAR since some variants will have 16MB of flash
that requires this to be enabled.

Remove the default speed and mode; these values are taken from the
device tree when CONFIG_DM_SPI_FLASH is enabled.

Add default bus, so that 'sf' detects the SPI flash by default.

Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: remove speed/mode; add bus; move winbond to defconfig]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
2017-11-16 11:45:20 +01:00
Jon Nettleton
b4b06ac6f7 arm: mvebu: clearfog: enable XHCI USB
Enable the driver by default for the clearfog boards since the external
port is configured for XHCI.

Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: split from the SoC setup patch]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
2017-11-16 11:45:20 +01:00
Tuomas Tynkkynen
ad12dc1844 cmd: Toggle the default value of CONFIG_CMD_IMLS
Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:

../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
   i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {

Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-10-10 17:51:04 -04:00
Chris Packham
7654f62f4e ARM: mvebu: Convert CONFIG_MVNETA to Kconfig
This converts the following to Kconfig:
   CONFIG_MVNETA

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2017-09-26 06:51:30 +02:00
Tom Rini
5dc4dfd2a9 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-28 07:16:32 -04:00
Tom Rini
88663126a0 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-14 20:00:40 -04:00
Simon Glass
6500ec7a5a Convert CONFIG_CMD_PCI to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_PCI

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-08-11 15:41:50 -04:00
Tom Rini
1989374b21 configs: Finish migration of PHY_GIGE
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-08 17:02:31 -04:00
Alexandru Gagniuc
3146f0c017 Move PHYLIB to Kconfig
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-08-07 15:22:28 -05:00
Simon Glass
2be296538e Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to Kconfig
This converts the following to Kconfig:
   CONFIG_ENV_IS_IN_MMC
   CONFIG_ENV_IS_IN_NAND
   CONFIG_ENV_IS_IN_UBI
   CONFIG_ENV_IS_NOWHERE

In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.

In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.

There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with

   ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC

And then manual updates.  This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-07-25 21:08:01 -04:00
Tom Rini
fb82fe3851 configs: Resync defconfigs
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-19 09:47:40 -04:00
Patrick Wildt
f3d9ec2a69 arm: mvebu: clearfog: generic distro bootcmd
Switch Clearfog to the generic distro defaults.  This has been taken
from a Debian mailing list thread:

https://lists.debian.org/debian-boot/2016/10/msg00026.html

Signed-off-by: Patrick Wildt <patrick@blueri.se>
Signed-off-by: Stefan Roese <sr@denx.de>
2017-05-31 07:42:52 +02:00
Tom Rini
8728c97eff configs: Re-sync
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-13 13:52:33 -04:00
Patrick Delaunay
b331cd6204 cmd, disk: convert CONFIG_PARTITION_UUIDS, CMD_PART and CMD_GPT
We convert CONFIG_PARTITION_UUIDS to Kconfig first.  But in order to cleanly
update all of the config files we must also update CMD_PART and CMD_GPT to also
be in Kconfig in order to avoid complex logic elsewhere to update all of the
config files.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-01-28 08:48:03 -05:00