Add script to automate NAND flash process. As for now the board has
two burn scripts - burn to boot from SPI NOR flash and burn to boot
from AEMIF NAND flash, rename burn_uboot script to burn_uboot_spi.
Also update README to contain NAND burn U-boot process description.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
The Keystone SoCs use the same NAND driver as Davinci.
This patch adds opportunity to write Keystone U-boot image to NAND
device using appropriate RBL ECC layout. This is needed only if RBL
boots U-boot from NAND device and that's supposed that raw u-boot
partition is used only for writing image.
The main problem is that default Davinci ECC layout is different from
Keystone RBL layout. To read U-boot image the RBL needs that image was
written using RBL ECC layout.
The BBT table is written using default Davinci layout and has to
be updated using one. The BBT can be updated only while erasing
chip or by forced bad block assigning, so erase function has to
use native ecc layout in order to be able to write BBT correctly.
So if we're writing to NAND U-boot address we use RBL layout for
others we use default ECC layout.
Also remove definition for CONFIG_CMD_NAND_ECCLAYOUT as there is no
reasons to use ECC layout commands. It was added by mistake.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Move AEMIF driver to drivers/memory/ti-aemif.c along with AEMIF
definitions collected in arch/arm/include/asm/ti-common/ti-aemif.h
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The definitions inside emif_defs.h concern davinci nand driver and
should be in it's header. So create header file for davinci nand
driver and move definitions from emif_defs.h and nand_defs.h to it.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
[trini: Fixup more davinci breakage]
Signed-off-by: Tom Rini <trini@ti.com>
Currently PWREMU_MGMT is not configured in the Linux generic UART
driver as this register seems to be specific TI UART IP. So this
needs to be enabled in u-boot to use UART1 from kernel space.
Acked-By: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Ethernet driver configures the CPSW, SGMI and Phy and uses
the the Navigator APIs. The driver supports 4 Ethernet ports and
can work with only one port at a time.
Port configurations are defined in board.c.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
currently only spi0 is enabled on k2hk evm. This
configuration update is needed to enable spi1 and spi2.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Tom Rini <trini@ti.com>
k2hk EVM is based on Texas Instruments Keystone2 Hawking/Kepler
SoC. Keystone2 SoC has ARM v7 Cortex-A15 MPCore processor. Please
refer the ti/k2hk_evm/README for details on the board, build and other
information.
This patch add support for keystone architecture and k2hk evm.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Sandeep Nair <sandeep_n@ti.com>
