This header file should not be included in other header files. Remove it
and use other headers and C inclusions instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.
Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.
This requires quite a few header-file additions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Calling 'mdio read ...' currently leads to a data abort when no mdio
bus is found.
To fix this, check if 'bus' is a valid pointer before accessing it.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adds UCLASS_MDIO DM class supporting MDIO buses that are probed as
stand-alone devices. Useful in particular for systems that support
DM_ETH and have a stand-alone MDIO hardware block shared by multiple
Ethernet interfaces.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Alex reported the following:
"
I'm doing some MDIO work on a freescale/NXP platform and I bumped into
errors with this command:
=> mdio r emdio#3 5 3
Reading from bus emdio#3
"Synchronous Abort" handler, esr 0x8600000e
elr: ffffffff862b8000 lr : 000000008200cce4 (reloc)
...
mdio list does not list any PHYs currently because ethernet is using DM
and the interfaces are not probed at this time. The PHY does exist
on the bus though.
The above scenario works with this commit reverted:
e55047ec51 cmd: mdio: Switch to generic
helpers when accessing the registers
The current code using generic helpers only works for PHYs that have
been registered and show up in bus->phymap and crashes for arbitrary
IDs. I find it useful to allow reading from other addresses over MDIO
too, certainly helpful for people debugging MDIO on various boards.
"
Fix this by reverting to use the raw MDIO bus operations in case there
is no PHY probed based on DT at the specified address.
This restores the old behavior for these PHYs, which means that the
newly introduced MMD-over-C22 helpers won't be available for them, but
at least they will be accessible again without crashing the system.
Fixes: commit e55047ec51 ("cmd: mdio: Switch to generic helpers when accessing the registers")
Reported-by: Alex Marginean <alexm.osslist@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Switch to use the generic helpers to access the MMD registers so that we
can used the same command also for C45 PHYs, C22 PHYs with direct and
indirect access and PHYs implementing a custom way to access the
registers.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
It is confusing that mdio commands work and report phy id as
decimal value when mii is working with hex values.
For example:
ZynqMP> mdio list
gem:
21 - TI DP83867 <--> ethernet@ff0e0000
ZynqMP> mdio read ethernet@ff0e0000 0
Reading from bus gem
PHY at address 21:
0 - 0x1140
ZynqMP> mii dump 21 0
Incorrect PHY address. Range should be 0-31
...
ZynqMP> mii dump 15
0. (1140) -- PHY control register --
(8000:0000) 0.15 = 0 reset
U-Boot normally takes hex values that's why this patch is changing mdio
command to handle hex instead of changing mii command to handle decimal
values.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Now that they are in their own directory, we can remove this prefix.
This makes it easier to find a file since the prefix does not get in the
way.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
