This rearrange and remove duplicate defines to make the code cleaner.
There is no need to read vendor area1 and use an offset each time, it is
easier and clearer to just use the reg offset defined in TRM, same as
the other vendor regs.
This also removes use of the misspelled const for the RK3588 CMDOUT reg,
it will be re-added when support for RK3588 is introduced.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove empty implementations of get_phy and set_enhanced_strobe ops.
Change driver set_enhanced_strobe to return 0 in order to allow missing
implementation of the ops.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Refactor set_ios_post ops to correctly set UHS Speed Select field values
according to TRM. Also set or unset Enhanced Strobe Enable bit and
eMMC Card present bit in set_ios_post, the Enhanced Strobe Enable bit
was never unset after switching to HS400ES mode.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Check return value from mmc_send_cmd and clear HOST_CONTROL2 when there
is an error. Also skip enable of interrupt signaling and remove a delay,
a delay is already happening in sdhci_send_command.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Change to configure clock and DLL in set_clock and config_dll ops
instead of in the set_ios_post ops.
With this change the output clock is turned off while configuring DLL
parameters, according to the design recommendations.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for the set_clock and config_dll sdhci_ops. Use of these ops
will allow configuration of DLL while the output clock is disabled.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove the unneeded emmc_phy_init now that the no-inverter flag is
handled correctly after commit 2321a991bb ("rockchip: sdhci: rk3568:
bypass DLL when clk <= 52 MHz").
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The device private data is misused in rockchip_sdhci_of_to_plat and
rockchip_sdhci_execute_tuning.
In these functions dev_get_priv is assigned to struct sdhci_host:
struct sdhci_host *host = dev_get_priv(dev);
Instead, the sdhci host should refer to host in struct rockchip_sdhc:
struct rockchip_sdhc *priv = dev_get_priv(dev);
struct sdhci_host *host = &priv->host;
Because host is the first member in struct rockchip_sdhc this is not a
real problem, lets fix it anyway and also use priv name consistently.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Set correct UHS Mode Select field value for UHS SDR25 (50MHz) mode.
Fixes: d1c0a2200a ("mmc: sdhci: Add support for HOST_CONTROL2 and setting UHS timings")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Set High Speed Enable bit for MMC High Speed (52MHz) mode.
Fixes: f12341a952 ("mmc: sdhci: Fix HISPD bit handling")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This adds support for the TRNG found in the RK3588 SoC to the
rockchip_rng driver so that it can be used for things such as
seeding randomness to Linux.
Changes in V3:
- Moved notes from commit to cover letter.
- Added Reviewed-By tag.
Changes in V2:
- Modified Kconfig to note that the Rockchip RNG driver supports all
versions of the hardware (v1, v2, and the trng in the rk3588).
Signed-off-by: Lin Jinhan <troy.lin@rock-chips.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
A RK3568 device tree pmic node can reference the I2S1_MCLKOUT_TX clock
in assigned-clocks, add dummy support to set parent of this clock to the
rk3568 cru driver.
Fixes probe of pmic driver and missing regulators on affected boards,
rk3568-evb and rk3568-rock-3a.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
IO mux selection is not working correctly for all pins. Sync mux route
data from linux to add any missing and update wrong trigger pins to fix
this. Also apply the pull-up fix needed for GPIO0 D3-D6.
Fixes: 1977d746aa ("rockchip: rk3568: add rk3568 pinctrl driver")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Booting from sdmmc on RK3588 currently works because of a workaround in
the device tree, clocks are reordered so that the driver use ciu-sample
instead of ciu, and the BootRom initializes sdmmc clocks before SPL is
loaded into DRAM.
The sdmmc clocks are normally controlled by TF-A using SCMI. However,
there is a need to control these clocks in SPL, before TF-A has started.
This adds a rk3588_scru driver to control the sdmmc clocks in SPL before
TF-A has started, using scru regs. It also adds a small glue driver to
bind the scmi clock node to the rk3588_scru driver in SPL.
Fixes: 7a474df740 ("clk: rockchip: Add rk3588 clk support")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Building U-Boot SPL with CLK_SCMI and SCMI_FIRMWARE Kconfig options
enabled and SPL_FIRMWARE disabled result in the following error.
drivers/clk/clk_scmi.o: in function `scmi_clk_gate':
drivers/clk/clk_scmi.c:84: undefined reference to `devm_scmi_process_msg'
drivers/clk/clk_scmi.c:88: undefined reference to `scmi_to_linux_errno'
drivers/clk/clk_scmi.o: in function `scmi_clk_get_rate':
drivers/clk/clk_scmi.c:113: undefined reference to `devm_scmi_process_msg'
drivers/clk/clk_scmi.c:117: undefined reference to `scmi_to_linux_errno'
drivers/clk/clk_scmi.o: in function `scmi_clk_set_rate':
drivers/clk/clk_scmi.c:139: undefined reference to `devm_scmi_process_msg'
drivers/clk/clk_scmi.c:143: undefined reference to `scmi_to_linux_errno'
drivers/clk/clk_scmi.o: in function `scmi_clk_probe':
drivers/clk/clk_scmi.c:157: undefined reference to `devm_scmi_of_get_channel'
make[1]: *** [scripts/Makefile.spl:527: spl/u-boot-spl] Error 1
make: *** [Makefile:2043: spl/u-boot-spl] Error 2
Add Kconfig option so that CLK_SCMI can be disabled in SPL to fix this.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The documentation for misc_read() says:
Return: number of bytes read if OK (may be 0 if EOF), -ve on error
The Rockchip efuse driver implements this so it should return the number
of bytes read rather than zero on success. Fix this so that the driver
follows the usual contract for read operations.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The documentation for misc_read() says:
Return: number of bytes read if OK (may be 0 if EOF), -ve on error
The Rockchip efuse driver implements this so it should return the number
of bytes read rather than zero on success. Fix this so that the driver
follows the usual contract for read operations.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for DSI Host controller on Rockchip RK3568. This driver
is heavily based on the Rockchip dw_mipi_dsi_rockchip.c driver in
Linux and the stm32_dsi.c driver in U-Boot. It should be easy to add
support for other SoCs as the only missing component from the mainline
driver is setting the VOP big or VOP little (which the rk3568 does
not have).
Driver was tested for use in sending commands to a DSI panel in order
to obtain the panel ID.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for the Innosilicon DSI-DPHY driver for Rockchip SOCs.
The driver was ported from Linux and tested on a Rockchip RK3566
based device to query the panel ID via a DSI command.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
For 2 GB LPDDR4 single-rank RAM with 16 rows, the Rockchip ddr init bin
prints:
"Bus Width=32 Col=10 Bank=8 Row=16 CS=1 Die Bus-Width=16 Size=2048MB"
U-Boot TPL prints:
"BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB"
Add missing high row detection so that U-Boot TPL prints Row=16, same as
the Rockchip ddr init bin:
"BW=32 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=2048MB"
Signed-off-by: Jonathan Liu <net147@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The GPIO V2 controller on RK3568 and RK3588 works very similar to
prior generation, main difference is the use of a write mask in the
upper 16 bits and register address offset have changed.
GPIO_VER_ID is a new register at 0x0078 that is used to determine when
the driver should use new or old register offsets and values. Earlier
generation return 0x0 from this offset.
Refactor code and add support for the GPIO V2 controller used in RK3568
and RK3588.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The current divider to calculate the bank ID can change.
Given the Rockchip TRM not all gpio-banks have 32 pins per bank.
The "gpio-ranges" syntax allows multiple items with variable number
of pins. Use a constant ROCKCHIP_GPIOS_PER_BANK as fixed divider.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The rk3288 pwm nodes synced from Linux make use of PCLK_RKPWM
instead of PCLK_PWM. They have the same pclk_cpu parent,
so add PCLK_RKPWM to rk3288_clk_get_rate().
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # chromebook-jerry
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In the current rk3288.dtsi file the compatible string for
the DisplayPort(DP) node ends with "edp". The string in the
binding ends with "dp" which conflicts with "cdn-dp" as a
search term. Add "rk3288-dp" as compare string to select
vop_id.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # chromebook-jerry
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for Rockchip rk3588 variant of pinctrl.
The driver is adapted from the Linux driver.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
[eugen.hristev@collabora.com:
port to latest U-boot, bring more changes from Linux
use translated pull values table]
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
mmc->tran_speed is max clock, but currently rk3568_sdhci_set_ios_post
uses it if its != 0, regardless of mmc->clock value, and it breaks
eMMC controller.
Without this patch 'mmc dev 0; mmc dev 1; mmc dev 0' is enough for
breaking eMMC, since first initialization sets mmc->mmc_tran speed
to non-zero value (26MHz in my case), and on subsequent re-init when
mmc layer asks for 400KHz it sets 26MHz instead.
Fix it by using MAX(mmc->tran_speed, mmc->clock)
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add driver for StarFive JH7110 to support ddr initialization in SPL.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Add a DM reset driver for StarFive JH7110 SoC.
Note that the register base address of reset controller is the
same with the clock controller. Therefore, there is no device
tree node alone for reset driver.It binds device node in
the clock driver
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
This adds support for the StarFive JH7110 SoC which also
feature this SiFive cache controller.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
In all these cases, the index on the LHS is immediately afterwards
used to access the array appearing in the ARRAY_SIZE() on the RHS - so
if that index is equal to the array size, we'll access
one-past-the-end of the array.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Remove the EDO mode support from as the FMC2 controller does not
support the feature.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Currently, in stm32_qspi_claim_bus(), QSPI_CR and QSPI_DCR registers
are saved in stm32_ospi_flash struct on first flash memory initialization
and restored on each flash accesses.
As the logic of spi-uclass.c changed since 'commit 741280e9ac
("spi: spi-uclass: Fix spi_claim_bus() speed/mode setup logic")'
set_speed() and set_mode() callbacks are called systematically when bus
speed or bus mode need to be updated, QSPI_CR and QSPI_DCR registers are
set accordingly.
So stm32_qspi_claim_bus() can be updated by removing QSPI_CR and QSPI_DCR
save/restore code and struct stm32_ospi_flash can be removed as well.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
For debug purpose, it should be useful to indicate the slew rate for
each pins.
Add ospeed register information for pins which are configured in
either alternate function or gpio output.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Implement a ARM SMCCC based driver that allow to use
a secure watchdog on the platform.
Signed-off-by: Lionel Debieve <lionel.debieve@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The ftwdt010 watchdog driver was deleted by
commit 11232139e3 ("nds32: Remove the architecture")
Return it to the codebase in a DM compatible form. Enable it in
sandbox_defconfig to test compilability.
Another platform using ftwdt010 will be submitted later.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This driver supports the bcm2835 watchdog found on
Raspberry Pi boards.
It is derived from the Linux driver and was tested
on two Raspberry Pi board versions (B+ and 3B+).
Signed-off-by: Etienne Dublé <etienne.duble@imag.fr>
Reviewed-by: Stefan Roese <sr@denx.de>
The first two patches are by Frieder Schrempf who joins as a reviewer for
the SPI NAND framework and drivers.
The following 2 patches are by Linus Walleij and are taken by the series
"Add Broadcom Northstar basic support".
Bin Meng makes static a list for octeontx.
Francesco Dolcini specifies MTD partitions on command line for
colibri-{imx6ull,imx7}.
-----BEGIN PGP SIGNATURE-----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=1lGu
-----END PGP SIGNATURE-----
Merge tag 'u-boot-nand-20230417' of https://source.denx.de/u-boot/custodians/u-boot-nand-flash
Pull request for u-boot-nand-20230417
The first two patches are by Frieder Schrempf who joins as a reviewer for
the SPI NAND framework and drivers.
The following 2 patches are by Linus Walleij and are taken by the series
"Add Broadcom Northstar basic support".
Bin Meng makes static a list for octeontx.
Francesco Dolcini specifies MTD partitions on command line for
colibri-{imx6ull,imx7}.
This patch adds Ethernet Switch support that found on R-Car S4
(r8a779f0) SoC. This is extracted from multiple patches from
downstream BSP, with additional rework of the network device
registration.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Phong Hoang <phong.hoang.wz@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[Marek: Rework the driver to support all ports via subdrivers.
Split the driver up, add generic PHY framework support.
Generic code clean ups.]
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add Renesas Ethernet SERDES driver for R-Car S4-8 (r8a779f0).
The datasheet describes initialization procedure without any information
about registers' name/bits. So, this is all black magic to initialize
the hardware. Especially, all channels should be initialized at once.
This driver is imported and adjusted from Linux 6.3-rc1 commit:
50133cd3e8dd1 ("phy: renesas: r8a779f0-eth-serdes: Remove retry code in .init()")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Use IS_ENABLED() instead of CONFIG_IS_ENABLED() to check for CONFIG_
option which is identical across all of U-Boot and xPL builds.
Fixes: 2769ddc99f ("mmc: tmio: Replace ifdeffery with IS_ENABLED/CONFIG_IS_ENABLED macros")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
octeontx_bch_devices and octeontx_pci_nand_deferred_devices are only
referenced in the files where they are defined. Make them static.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
Link: https://lore.kernel.org/all/20230405143837.785082-1-bmeng@tinylab.org/
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Add support for the iproc Broadcom NAND controller,
used in Northstar SoCs for example. Based on the Linux
driver.
Cc: Philippe Reynes <philippe.reynes@softathome.com>
Cc: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/all/20230308214231.378013-1-linus.walleij@linaro.org/
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
For BRCMNAND with 1-bit BCH ECC (BCH-1) such as used on the
D-Link DIR-885L and DIR-890L routers, we need to explicitly
select the ECC like this in the device tree:
nand-ecc-algo = "bch";
nand-ecc-strength = <1>;
nand-ecc-step-size = <512>;
This is handled by the Linux kernel but U-Boot core does
not respect this. Fix it up by parsing the algorithm and
preserve the behaviour using this property to select
software BCH as far as possible.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/all/20230308212851.370939-1-linus.walleij@linaro.org/
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
- DDR Training sequence happens very fast. The speedup in boot time is
negligible by skipping the training sequence during 2nd boot or after.
So remove the check and skip.
- This change improves the robustness of DDR training. If u-boot crashed
during DDR training, the training could be left in a limbo state, where
the BootROM has recorded that it is already in a 2nd boot. The training
must be repeated in this scenario to get out of this limbo state, but due
to the check it cannot be performed.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Now that all differences in functionality are covered by individual
flags, remove the enumeration of SoC variants.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
While R40 puts the EMAC syscon register at a different address from
other variants, the relevant portion of the register's layout is the
same. Factor out the register offset so the same code can be shared
by all variants. This matches what the Linux driver does.
This change provides two benefits beyond the simplification:
- R40 boards now respect the RX delays from the devicetree
- This resolves a warning on architectures where readl/writel
expect the address to have a pointer type, not phys_addr_t.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Describe this feature instead of using the SoC ID.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Describe this feature instead of using the SoC ID.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Currently, EMAC variants are distinguished by their identity, but this
gets unwieldy as more overlapping variants are added. Add a structure so
we can describe the individual feature differences between the variants.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The HDMI PHY depends on the HVCC supply being enabled. So far we have
relied on it being enabled by an earlier firmware stage (SPL or TF-A).
Attempt to enable the regulator here, so we can remove that dependency.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
This abstracts away the CCU register layout, which is necessary for
supporting new SoCs like H6 with a reorganized CCU. One of the resets is
referenced from the PHY node instead of the controller node, so it will
have to wait until the PHY code is factored out to a separate driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
This driver is actually used for powerpc and m68k/ColdFire.
On ColdFire SoC's, interrupt flag get not set if IIEN flag (mbcr bit6,
interrupt enabled) is not set appropriately before each transfert.
As a result, the transfert hangs forever waiting for IIEN.
This patch set IIEN before each transfert, while considering this fix
as not harming powerpc arch.
Signed-off-by: Angelo Dureghello <angelo@kernel-space.org>
The IS_ENABLED, which does not consider SPL build, should be replaced
by CONFIG_IS_ENABLED.
For the case that we only enable DM CLK for u-boot but not in SPL, the
IS_ENABLED(CONFIG_CLK) still returns true, then cause clock failure.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Current code use dm_gpio_get_value() to get SDA and SCL value, and the
value depends on whether DTS file config the GPIO_ACTIVE_LOW. In ususal
case for i2c GPIO, DTS need to set GPIO_ACTIVE_LOW for SCL/SDA pins. So
here the logic is not correct.
And we must not use GPIOD_ACTIVE_LOW in client code include the
dm_gpio_set_dir_flags(), it is DTS's responsibility for this flag. So
remove GPIOD_ACTIVE_LOW here.
Fixes: aa54192d4a ("dm: i2c: implement gpio-based I2C deblock")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Alexander Kochetkov <al.kochet@gmail.com <mailto:al.kochet@gmail.com>>
This code first figures out if there is an i2c,speeds property, if so
its size in u32s, and then reads the value into the local speeds[]
array. Both 'size' and 'speeds' are completely unused thereafter.
It's not at all clear what this is supposed to do. Of course, it could
be seen as a sanity check that the DT node does have an i2c,speeds
property with an appropriate number of elements, but for that one
wouldn't actually need to read it into speeds[]. Also, I can't find
anywhere else in the U-Boot code which makes use of values from that
property (this is is the only C code referencing "i2c,speeds"), so it
seems pointless to insist that it's there.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
All build targets using this driver already use DM_MMC. So let's depend
this driver on this Kconfig symbol and remove the non-DM driver part.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
CONFIG_MMC_SDHCI_IO_ACCESSORS is not supported and/or used by this
driver so let's remove these unused parts completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This driver already depends on CONFIG_ARCH_MVEBU, so there is no need
to have some checks for this Kconfig symbol in the driver itself. Let's
remove these superfluous checks.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The default erase command applies on erase group unit, and
simply round down to erase group size. When the start block
is not aligned to erase group size (e.g. erasing partition)
it causes unwanted erasing of the previous blocks, part of
the same erase group (e.g. owned by other logical partition,
or by the partition table itself).
To prevent this issue, a simple solution is to use TRIM as
argument of the Erase command, which is usually supported
with eMMC > 4.0, and allow to apply erase operation to write
blocks instead of erase group
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
When secure/insecure TRIM operations are supported.
When used as erase command argument it applies the
erase operation to write blocks instead of erase
groups.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
- improve tegra DC driver to work with panel ops and implement
native 180 degree panel rotation support
- add T30 support to tegra DC driver
- add DSI driver (based on mainline Linux one with minor
adjustments, only T30 tested)
- add get_display_timing ops to simple panel driver
- extend simple panel driver to use it for MIPI DSI panels
which do not require additional DSI commands for setup
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCZDBwUw4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXL3+AJ9EkQKAWXZtlYdAOVl4/nzJnuTCAQCfY58zkDsw
TnAlwmMGWFl3RF6yGXY=
=uYUp
-----END PGP SIGNATURE-----
Merge tag 'video-20230407' of https://source.denx.de/u-boot/custodians/u-boot-video
- fix building sandbox without SDL
- improve tegra DC driver to work with panel ops and implement
native 180 degree panel rotation support
- add T30 support to tegra DC driver
- add DSI driver (based on mainline Linux one with minor
adjustments, only T30 tested)
- add get_display_timing ops to simple panel driver
- extend simple panel driver to use it for MIPI DSI panels
which do not require additional DSI commands for setup
The DM_REGULATOR symbol has SPL counterpart in:
drivers/power/regulator/Kconfig:config SPL_DM_REGULATOR
Use CONFIG_IS_ENABLED() macro to match on the correct
variant depending on the build stage.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The DM_REGULATOR symbol has SPL counterpart in:
drivers/power/regulator/Kconfig:config SPL_DM_REGULATOR
Use CONFIG_IS_ENABLED() macro to match on the correct
variant depending on the build stage.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The DM_REGULATOR symbol has SPL counterpart in:
drivers/power/regulator/Kconfig:config SPL_DM_REGULATOR
Use CONFIG_IS_ENABLED() macro to match on the correct
variant depending on the build stage.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The DM_REGULATOR symbol has SPL counterpart in:
drivers/power/regulator/Kconfig:config SPL_DM_REGULATOR
Use CONFIG_IS_ENABLED() macro to match on the correct
variant depending on the build stage.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The DM_REGULATOR symbol has SPL counterpart in:
drivers/power/regulator/Kconfig:config SPL_DM_REGULATOR
Use CONFIG_IS_ENABLED() macro to match on the correct
variant depending on the build stage.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The DM_REGULATOR symbol has SPL counterpart in:
drivers/power/regulator/Kconfig:config SPL_DM_REGULATOR
Use CONFIG_IS_ENABLED() macro to match on the correct
variant depending on the build stage.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Re-use simple panel driver for MIPI DSI panels
which do not require additional DSI commands
for setup.
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101 T20
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # Paz00
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF700T T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Some cases may require passing display timings from
panel driver. To handle such cases support parsing
device tree panel node for timing subnode.
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101 T20
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # Paz00
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Google Nexus 7 2012
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Adds support for both DSI outputs found on Tegra. Only very
minimal functionality is implemented, so advanced features
like ganged mode won't work. Driver is heavily based on
mainline Tegra DSI and re-uses much of its features.
Only T30 is supported for now but T20 support can be added
if any supported devices will be found.
Driver is wrapped as panel driver since Tegra DC driver supports
only panel drivers calls.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF600T T30
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # HTC One X T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Internal video devices like DSI and HDMI controllers
require sending commands into DC register field.
To make this available, lets create platform data,
which is restricted to pass DC regmap only to
pre-defined devices.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF T30
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # Paz00
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101 T20
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # HTC One X T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Tegra DC driver does not call panel_set_backlight, which can
result in absence of backlight on device. Fix this by calling
panel_set_backlight with BACKLIGHT_DEFAULT just after
panel_enable_backlight.
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101 T20
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # Paz00
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF T30
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # LG P895 T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Unlike 90 and 270 degree rotation, 180 degree rotation is more
common and does not require scaling. Implement it for correct
grouper support.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # Google Nexus 7 2012
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Google Nexus 7 2012
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Check if panel driver has display timings and get those.
If panel driver does not pass timing, try to find timing
under rgb node for backwards compatibility.
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101 T20
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # Paz00
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF T30
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # LG P895 T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
DISP1 clock may use PLLP, PLLC and PLLD as parents.
Instead of hardcoding, lets pass clock and its
parent from device tree. Default parent is PLLP.
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101 T20
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # Paz00
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF T30
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # HTC One X T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Move tegra dc driver to tegra20 directory and also mention
T30 in description of the driver's config option.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
[agust: add commit description]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
On popular request make the display driver from T20 work on T30 as
well. Turned out to be quite straight forward. However a few notes
about some things encountered during porting: Of course the T30 device
tree was completely missing host1x as well as PWM support but it turns
out this can simply be copied from T20. The only trouble compiling the
Tegra video driver for T30 had to do with some hard-coded PWM pin
muxing for T20 which is quite ugly anyway. On T30 this gets handled by
a board specific complete pin muxing table. The older Chromium U-Boot
2011.06 which to my knowledge was the only prior attempt at enabling a
display driver for T30 for whatever reason got some clocking stuff
mixed up. Turns out at least for a single display controller T20 and
T30 can be clocked quite similar. Enjoy.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF T30
Tested-by: Jonas Schwöbel <jonasschwoebel@yahoo.de> # Surface RT T30
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # LG P895 T30
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Add pinctrl tables for R8A779G0 V4H SoC.
Based on Linux next 20230228 PFC tables tables up to
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: LUU HOAI <hoai.luu.ub@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Phong Hoang <phong.hoang.wz@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync with Linux next 20230228, sort sh_pfc_pinconf_set voltage args]
Add clock tables for R8A779G0 V4H SoC from Linux next
commit 058f4df42121 ("Add linux-next specific files for 20230228")
There is an adjustment to the clock tables to make them easier suitable
for U-Boot, PLL2 is not treated as GEN4 PLL type PLL2_VAR, but rather a
plain PLL2. This should be sufficient until PLL2_VAR is implemented in
the clock core.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync with Linux next 20230228 . Update from CLK to CPG core driver
Treat PLL2 as non-PLL2_VAR for now]
Add pinctrl tables for R8A779F0 S4 SoC.
Based on Linux next 20230228 PFC tables tables up to
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: LUU HOAI <hoai.luu.ub@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Use RCAR_64 Kconfig, sync with Linux next 20230228]
Add clock tables for R8A779F0 S4 SoC
Based on Linux commit 24aaff6a6ce4 ("clk: renesas: cpg-mssr: Add support
for R-Car S4-8") by Yoshihiro Shimoda and sync the tables up to Linux next
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync with Linux next 20230228 . Update from CLK to CPG core driver]
Update R-Car Gen4 support in Gen3 clock driver. This patch renames the
V3U clock parts to Gen4 and extends them by new PLL2, PLL3, PLL4, PLL6
as well as SDSRC clock which use undocumented bits so far, and RPCSRC
clock which uses its own more capable divider table. The Gen4 module
standby and reset tables are also updated.
This patch makes use of union to alias Gen3 and more extensive Gen4
PLL tables, as the driver cannot ever be instantiated on hardware
that would identify itself as both Gen3 and Gen4.
The V3U clock driver is updated to match Gen4 clock driver behavior,
it is augmented with a more extensive PLL table and a valid MODEMR
register offset.
This supersedes "clk: renesas: Introduce R-Car Gen4 CPG driver"
from Hai Pham as the R-Car Gen3 and Gen4 clock core drivers are
extremely similar. That implementation was in turn based on Linux
commit 470e3f0d0b15 ("clk: renesas: rcar-gen4: Introduce R-Car Gen4 CPG driver")
by Yoshihiro Shimoda .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Use CONFIG_RCAR_64 to make the driver available on both
R-Car Gen3 and R-Car Gen4.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Provide the basic HSCIF support for R-Car SoC.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Fill in HSSRR offset for Gen2 and SCBRR calculation for Gen2 and Gen3]
Reviewed-by: Simon Glass <sjg@chromium.org>
Add R-Car Gen4 family support. The basic function is as same as previous
R-Car Generation.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Swap RZ/A1 and Gen4 to keep the GenN sequence, use RCAR_64]
Add support for R-Car Gen4 SoCs and a matching DT compatible.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Drop SoC specific compatible, use RCAR_64 Kconfig symbol, update commit message]
Support R-Car Gen4 family. The default quirk is similar to previous
generation.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # Use RCAR_64 Kconfig
Instead of #if and #ifdef, use IS_ENABLED and CONFIG_IS_ENABLED macros.
This improves build test coverage. The CONFIG_SPL_BUILD must remain an
ifdef, as CONFIG_SPL_STACK may not always be defined, e.g. in U-Boot
proper build. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The 64bit limitation check is compiled and optimized out on 32bit
platforms, but generates a type width warning:
drivers/mmc/tmio-common.c: In function ‘tmio_sd_addr_is_dmaable’:
drivers/mmc/tmio-common.c:376:26: warning: right shift count >= width of type [-Wshift-count-overflow]
376 | if (addr >> 32)
| ^~
Fix the warning by checking the addr type width to see whether the
shift even makes sense in the first place. The width check is also
optimized out at compile time.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add support for R-Car Gen4 SoCs into the driver.
While I2C on R-Car Gen4 does support some extra features (Slave Clock
Stretch Select), for now it is treated the same as I2C on R-Car Gen3,
which let us share the same driver.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # Use RCAR_64 Kconfig
Reviewed-by: Heiko Schocher <hs@denx.de>
Add support for the GPIO controller block in the R-Car Gen4 family.
It has a General Input Enable Register (INEN), whose reset state is to
have all inputs disabled.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add two new callbacks matching the Linux ones. The .set_mode is used to set
PHY mode and submode, where mode is either USB, Ethernet, and so on, while
submode is e.g. for Ethernet case RGMII, RMII, and so on. The .set_speed is
used to configure link speed into the PHY. Unlike the existing configure
callback, which is used to pass arbitrary custom information to the PHY,
these two callbacks are used to pass standardized set of information to
the PHY.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Pull Marvell 10G PHY driver from Linux 6.1.y as of commit
d6d29292640d3 ("net: phy: marvell10g: select host interface configuration")
and heavily adapt to match U-Boot PHY framework. Support for
hwmon is removed as is much other functionality which could
not be tested, this results in much simpler driver which can
only bring the PHY up and set MAC type.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add phy_modify_mmd()/phy_modify_mmd_changed() from Linux 5.1.y as of commit
b8554d4f7288f ("net: phy: add register modifying helpers returning 1 on change")
This is used by the upcoming Marvell 10G PHY driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Import marvell_phy.h from Linux 5.14.y as of commit
a5de4be0aaaa6 ("net: phy: marvell10g: fix differentiation of 88X3310 from 88X3340")
and use it in marvell PHY driver instead of current ad-hoc macros.
Two of the PHY IDs are unknown to Linux, 88E1149S and 88E1680, for
those two, only sync the length of the hexadecimal number to 8 digits.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Synchronize PHY interface modes with Linux next 6.2.y commit:
0194b64578e90 ("net: phy: improve phy_read_poll_timeout")
Retain LX2160A/LX2162A PHY modes as those are not yet supported
by the Linux kernel, but isolate those with ifdeffery.
Isolate NCSI which are also not supported by Linux kernel. Note
that the ifdeffery cannot be avoided with IS_ENABLED() here due
to compilation of the entire conditional, which would fail in
case NCSI symbols are not available.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Replace PHY_INTERFACE_MODE_SFI with PHY_INTERFACE_MODE_5GBASER,
PHY_INTERFACE_MODE_10GBASER and PHY_INTERFACE_MODE_XAUI to match
Linux PHY interface modes.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This mode does not seem to be well defined and used anywhere, remove support for it.
Based on discussion:
- 1000baseX does c37 AN of duplex+pause
- SGMII does AN of duplex+pause+speed, at lower speed bytes are repeated 10x/100x
- 2500baseX does not do AN, or does very different c73 AN
- SGMII 2500 behavior is unclear
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The phy_init() is now used only to perform manual relocation of PHY
driver callbacks. Wrap it in ifdeffery and only call it on systems
which still require manual relocation, i.e. m68k .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Wrap phy_drv_reloc() back into phy_init() to reduce ifdeffery,
since phy_drv_reloc() is now called only from one call site.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
This function is no longer used, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
The static phy_drivers list is superseded by linker list of struct phy_drivers
now that all drivers have been converted to the later. Drop the phy_drivers
list as well as list_head from struct phy_driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
This particular PHY driver is slightly more spread out across additional
source files. Since the phy_register() calls are no longer necessary, all
the registration calls across those source files is dropped. Furthermore,
the Makefile can now be updated to only compile generic TI PHY support if
matching Kconfig symbol is enabled and the ifdeffery in the generic TI PHY
driver can be dropped.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.
Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Introduce U_BOOT_PHY_DRIVER() macro which is used to add struct phy_driver
into a new linker list section containing all compiled in struct phy_driver
drivers. This is so far empty until PHY drivers are converted over to this
macro.
Iterate over both drivers registered using soon to be legacy phy_register()
as well as drivers in the new linker list when looking up a suitable PHY
driver. This way, PHY drivers can be converted over to the new macro one
driver at a time.
The relocation of callbacks for linker list based drivers now happens in
phy_init() call as the drivers are available at that point in time, and
phy_register() is not called for those drivers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Create separate function to implement manual relocation of PHY driver
functions and make use of that function. This is a preparatory patch
for introduction of PHY driver definition using linker lists.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
These struct phy_driver ... instances are local to this source code
file, staticize them. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
These struct phy_driver ... instances are local to this source code
file, staticize them. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
These struct phy_driver ... instances are local to this source code
file, staticize them. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
These struct phy_driver ... instances are local to this source code
file, staticize them. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
CONFIG_SYS_SCSI_MAX_SCSI_ID is not defined if CONFIG_SCSI=n.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Building with CONFIG_AHCI_PCI=y and CONFIG_SCSI_AHCI=n leads to
drivers/ata/ahci-pci.o: in function `ahci_pci_probe':
drivers/ata/ahci-pci.c:21: undefined reference to `ahci_probe_scsi_pci'
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Freescale ESPI driver (CONFIG_FSL_ESPI) relies to the MPC85xx platform
(PowerPC) through arch/powerpc/include/asm/immap_85xx.h. The driver can't
compile on another architecture/platform.
Signed-off-by: Corentin Guillevic <corentin.guillevic@smile.fr>
On mpc832x, SPI can be either handled by CPU or QE.
In order to work in CPU mode, bit 17 of SPMODE has to
be set to 1, that bit is called OP.
Also, data is located at a different place than the one expected
by the driver today. In 8 bits mode with REV set, data to be
transmitted is located in the most significant byte while
received data is located in second byte. So perform the
necessary shifts.
In order to differentiate with other CPUs, a new compatible is
added for mpc832x: fsl,mpc832x-spi
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
The mpc832x has GPIOs handled by the QUICC Engine.
The registers are different from the one for the
non QE mpc83xx GPIOs.
Implement a GPIO driver for those.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
gd->arch.sdhc_clk only exists when CONFIG_FSL_ESDHC is set,
so enclose it inside ifdefs.
gd->arch.qe_clk and gd->arch.brg_clk must be populated when
CONFIG_QE is set.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Introduce a new compatible "fsl,pq2pro-wdt"
On mpc83xx, the prescaling factor is 0x10000.
Don't write the watchdog configuration register in
start.S as it can be written only once.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
mpc8xx, mpc83xx and mpc86xx have similar watchdog with almost same
memory registers.
Refactor the driver to get the register addresses from the
device tree and use the compatible to know the prescale factor.
Calculate the watchdog setup value from the provided timeout.
Don't declare it anymore as an HW_WATCHDOG, u-boot will start
servicing the watchdog early enough.
On mpc8xx the watchdog configuration register is also used for
configuring the bus monitor. So add it as an option to the watchdog
when it is mpc8xx. When watchdog is not selected, leave the
configuration of the initial SYPCR from Kconfig.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
mpc8xx, mpc83xx and mpc86xx have similar watchdog with almost same
memory registers.
Rename it mpc8xxx which is the generic name used for drivers supporting
several mpc families.
The driver will be made more generic in following patch.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Allow a slice of an existing block device to be mapped to a
blkmap. This means that filesystems that are not stored at exact
partition boundaries can be accessed by remapping a slice of the
existing device to a blkmap device.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Allow a slice of RAM to be mapped to a blkmap. This means that RAM can
now be accessed as if it was a block device, meaning that existing
filesystem drivers can now be used to access ramdisks.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
blkmaps are loosely modeled on Linux's device mapper subsystem. The
basic idea is that you can create virtual block devices whose blocks
can be backed by a plethora of sources that are user configurable.
This change just adds the basic infrastructure for creating and
removing blkmap devices. Subsequent changes will extend this to add
support for actual mappings.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With vendor boot image introduced in version 3 and 4 of boot
image header, boot information is located in both boot image
and vendor boot image.
Flashing zImage is not supported for version 3 and 4 since this
requires updating vendor boot image and/or generating a new image.
Print an error message when the boot image header version is
greater than 2.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
With the new vendor boot image introduced in versions 3 and 4
of boot image header, the header check must be done for both boot
image and vendor boot image. Thus, replace android_image_check_header()
by is_android_boot_image_header() to only refer to boot image header check.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Android introduced boot header version 3 or 4.
The header structure change with version 3 and 4 to support
the new updates such as:
- Introducing Vendor boot image: with a vendor ramdisk
- Bootconfig feature (v4)
Change andr_img_hdr struct name to maintain support for version v0,
v1 and v2 while introducing version 3 and 4.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
The spl_board_prepare_for_boot() should be called before jump_to_image_no_args()
to perform board-specific deinitialization before jumping to the next stage.
This board-specific deinitialization can be very much anything, e.g. disable
dcache in case it was enabled, or such.
Add the missing spl_board_prepare_for_boot() call into f_sdp .
Signed-off-by: Marek Vasut <marex@denx.de>
Sometimes a multi-element array is used for "gpio-ranges" property in
dts file:
qe_pio_e: gpio-controller@1460 {
......
gpio-ranges = <&pinctrl1 0 20 10>, <&pinctrl2 10 50 20>;
......
};
But the function pinctrl_gpio_get_pinctrl_and_offset can't handle this
case because the "index" argument passed to dev_read_phandle_with_args
is fixed to be "0". Use a loop to traverse the array to fix it.
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
A condition in the rk3399 RAM initialization code used the old
CONFIG_RAM_RK3399_LPDDR4 constant name. This commit changes the
condition to use the correct CONFIG_RAM_ROCKCHIP_LPDDR4 constant.
Reviewed-by: Simon Glass <sjg@chromium.org>
%s/supporedt/supported/
Fixes: edca8cf721 ("Convert CONFIG_SCSI_AHCI_PLAT et al to Kconfig")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
---------------------------------
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/15819
i.MX patches queued for next:
- Conversions to DM_SERIAL
- Fixes for Toradex boards
- Gateworks Boards
- i.MX8ULP
- EQoS support / fixes, changes in boards
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCZCaU0Q8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76YCKgCgk4OueoIggmes+Ccj8bu1BcQbrfYAoJAgMeKE
It0hrVAifD62TPb2rmHt
=hFVG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-next-20230331' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx into next
u-boot-imx-next-20230331 for next
---------------------------------
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/15819
i.MX patches queued for next:
- Conversions to DM_SERIAL
- Fixes for Toradex boards
- Gateworks Boards
- i.MX8ULP
- EQoS support / fixes, changes in boards
It should return -EINPROGRESS if successful otherwise sysreset-uclass
will continue to the next sysreset device.
Signed-off-by: Jonathan Liu <net147@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove need of dts binding for button keyboard since it reuses
gpio-keys binding. Select gpio-keys driver if button keyboard
is selected since button keyboard can not operate on its own.
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # HTC One X T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adding support for Analog Devices MAX313XX series RTCs.
This is ported from the Linux driver and adapted for use in u-boot.
Notable differences are
- handling of tm_year and tm_mon differ
- clock source support is omitted
- hwmon support for the MAX31328 and MAX31343 is omitted
- rtc_ops->reset is added
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The API is more convenient to use if one doesn't have to know upfront
which gpio controller has a line with the name one is searching for,
and arrange to look that device up somehow. Or implement this loop
oneself.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
These operations are required by dm_rtc_read and
dm_bootcount_get helpers.
Signed-off-by: Thomas Perrot <thomas.perrot@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reports the sandbox swapcase PCI Express device to support a 256 byte
Maximum Payload Size for MPS tuning tests.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There can certainly be a lot more elements in the "revisions" (and
"names") arrays than there are gpios used to form the trinary number
we're searching for; we simply don't know the array size up-front.
Nor do we need to, because the loop body already knows to recognize
-EOVERFLOW as "not that many elements present" (and we have a test
that specifically ensures that dev_read_u32_index() returns exactly
that). So just drop the i < priv->gpio_num condition.
While in here, fix the weird placement of the default: keyword.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Implement common board_interface_eth_init() and call it from the FEC
driver to configure IOMUXC GPR[1] register according to the PHY mode
obtained from DT. This supports all three interface modes supported by
the i.MX8M Mini/Nano/Plus FEC and supersedes the current board-side
configuration of the same IOMUX GPR[1] duplicated in the board files.
Signed-off-by: Marek Vasut <marex@denx.de>
The FEC ref clock frequency on i.MX8M Mini/Nano/Plus was so far configured
via ad-hoc board code. Replace that with DM clock clk_set_rate() instead.
This way, the driver claims all its required clock and sets the ref clock
rate, without any need of architecture specific register fiddling.
Signed-off-by: Marek Vasut <marex@denx.de>
Implement common board_interface_eth_init() and call it from the DWMAC
driver to configure IOMUXC GPR[1] register according to the PHY mode
obtained from DT. This supports all three interface modes supported by
the i.MX8M Plus DWMAC and supersedes current board-side configuration
of the same IOMUX GPR[1] duplicated in the board files.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
With DM clock support in place, it is easy to add RMII support into the
MAC driver. The RMII cannot operate at 1000 Mbps and at 100 and 10 Mbps
the clock frequency is 50 MHz and 5 MHz instead of 25 MHz and 2.5 MHz.
The board DT requires the following adjustments to EQoS node:
phy-mode = "rmii";
assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_266M>,
<&clk IMX8MP_SYS_PLL2_100M>,
<&clk IMX8MP_SYS_PLL2_50M>;
assigned-clock-rates = <0>, <100000000>, <50000000>;
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
The DWMAC clock in i.MX8M Plus were so far configured via ad-hoc
architecture code. Replace that with DM clock instead. This way,
the driver claims all its required clock, enables and disables
them, and even gets the CSR clock rate and sets the TX clock rate,
without any need of architecture specific register fiddling. Drop
the architecture specific code while at it too.
The adjustment here is modeled after STM32MP15xx clock handling
in this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver currently only waits for DMA_MODE SWR bit to clear itself.
This is insufficient e.g. on i.MX8M Plus, where the MAC must be reset
before IOMUX GPR[1] content is latched into the MAC and used. Without
the proper reset, the i.MX8M Plus MAC variant does not take the value
in IOMUX GPR[1] into account, which makes it impossible e.g. to switch
interface mode from RGMII to any other.
Since proper reset is desired in general to put the block into defined
state, always assert the DMA_MODE SWR bit before waiting for the bit
to clear itself.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
This function is only used within the driver, staticize it.
Fixes: 149e80f74b ("net: dwc_eth_qos: public some functions")
Signed-off-by: Marek Vasut <marex@denx.de>
The dm_gpio_free() is never called, because for stm32, the phy_reset_gpio
pointer is never valid. This is because only tegra186 ever claims the
phy_reset_gpio, all other platforms use the PHY framework to reset the
PHY instead. Drop the dm_gpio_free() and dm_gpio_is_valid().
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
The return is never triggered due to the goto just above it.
Drop it. No functional change.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Move the board_interface_eth_init() into common ethernet uclass code,
since this function could be shared by multiple drivers.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Add clock for the DWMAC EQoS block. This is used among other things
to configure the MII clock via DM CLK.
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Marek Vasut <marex@denx.de>
The ocotp driver is available for regular and SPL builds using the
(SPL_)MXC_OCOTP configuration. Also, the ocotp driver does not support
the driver model (DM) configuration.
But, for SPL builds, the SPL_MXC_OCOTP configuration depends on
SPL_MISC which implies on SPL_DM.
This commit replaces the dependency on SPL_MISC with SPL_DRIVERS_MISC.
So the only requirement is to have enabled miscellaneous drivers for
the SPL.
Signed-off-by: Jean-Marie Lemetayer <j.lemetayer@kerlink.fr>
PCA9451A uses similar BUCKs and LDO regulators as PCA9450B/C but
has LDO2 and LDO3 removed. So reuse pca9450 PMIC and regulator driver
and add new type for PCA9451A.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Remove legacy command definitions, change to use new ELE_xxx command
request.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add get_events API to retrieve any singular events that has occurred
since the FW has started from sentinel
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The ECC fuse on 8ULP can't be written twice. If any user did it, the
ECC value would be wrong then cause accessing problem to the fuse.
The patch will lock the ECC fuse word to avoid this problem.
For iMX9, the OTP controller automatically prevents an ECC fuse word to
be written twice. So it does not need the setting.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Since new 8ULP A1 S400 FW (v0.0.8-e329b760) can support to read
more fuses: like PMU trim, Test flow/USB, GP1-5, GP8-10. Update
the u-boot driver for the new mapping.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Alice Guo <alice.guo@nxp.com>
To align with ARM trusted firmware's change, adjust DRAM timing
save area to new position 0x20055000. So we can release the space
since 0x2006c000 for the NOBITS region of ARM trusted firmware
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
The Linux devicetrees for Apple silicon devices are after review
feedback switching from deleting unused PCIe ports to disabling them.
Link: https://lore.kernel.org/asahi/1ea2107a-bb86-8c22-0bbc-82c453ab08ce@linaro.org/
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
The WIZ acts as a wrapper for SerDes and has Lanes 0 and 2 reserved
for USB for type-C lane swap if Lane 1 and Lane 3 are linked to the
USB PHY that is integrated into the SerDes IP. The WIZ control register
has to be configured to support this lane swap feature.
The support for swapping lanes 2 and 3 is missing and therefore
add support to configure the control register to swap between
lanes 2 and 3 if PHY type is USB.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
